wavetrac truetrac s trac ?

[tiddlar]

i bought the moser m 9 housing. Heard wavetrac is better than truetrac, and has lifetime warranty but people are breaking them. Midwest chassis, has a car running 9's on slicks and runs an s trac, has had it 4 years without a glitch. Can my moser housing accept the s trac? If not im stuck with wavetrac.... anyone have experiences with any of these? The truck is 89% street and the rest strip. I might put slicks on for the track. ill have mt s/r for street, t56 tranny, 1000 hp sbc twin turbo. Heavy 53 chevy truck. I dont think I will put it through too much abuse, but i would rather save myself the headaches. Thank you in advance gentlmen.

[BigDan3131]

Why aren't you just using the tried and true Detroit Locker? As long as its a 9" part any diff can be installed as long as the spline count is the same.

[tiddlar]

Originally Posted by BigDan3131

Why aren't you just using the tried and true Detroit Locker? As long as its a 9" part any diff can be installed as long as the spline count is the same.

I've been googling and googling and from what I understood the Detroit locker will be "clunking" around turns and waveyrac and strac are better for street/strip

[BigDan3131]

If your making 1000hp and your exhaust is noisy there is no way you can hear it and its not a clunk clunk noise, its more of a click click click noise since its disengaging the gears as you turn the corner. Since were in trucks and the cab will be insulated I doubt you will hear it over the exhaust. Better to have a little noise then to start breaking stuff isn't it?

[C10Greg]

I have a moser M9 fabricated housing. I am running moser 35 spline axles with a Strange S Trac and Strange HD Pro Aluminum Case. Can't tell you anything else about it yet because it is at the rear end shop getting built.

[tiddlar]

Originally Posted by C10Greg

I have a moser M9 fabricated housing. I am running moser 35 spline axles with a Strange S Trac and Strange HD Pro Aluminum Case. Can't tell you anything else about it yet because it is at the rear end shop getting built.

O man, that's what I am leaning towards. Midwest chassis has a car running 9's on slicks with s trac 0 problems. They as well suggested the pro hd aluminum. I already have the moser m9 housing with 35 spline axles. I guess we will test it out together.

[tiddlar]

Originally Posted by BigDan3131

If your making 1000hp and your exhaust is noisy there is no way you can hear it and its not a clunk clunk noise, its more of a click click click noise since its disengaging the gears as you turn the corner. Since were in trucks and the cab will be insulated I doubt you will hear it over the exhaust. Better to have a little noise then to start breaking stuff isn't it?

You do make a valid point ...

[tiddlar]

Originally Posted by C10Greg

I have a moser M9 fabricated housing. I am running moser 35 spline axles with a Strange S Trac and Strange HD Pro Aluminum Case. Can't tell you anything else about it yet because it is at the rear end shop getting built.

Where did you purchase your center section and how much?

[C10Greg]

Originally Posted by tiddlar

Where did you purchase your center section and how much?

I bought everything from Summit and I purchased it all individually. I think the HD Pro Aluminum Case was $785, the S Trac was $995 and the REM and EDM polished 3:89 Motive gears from C&R Racing but I don't remember what I paid for them.

[tiddlar]

Originally Posted by C10Greg

I bought everything from Summit and I purchased it all individually. I think the HD Pro Aluminum Case was $785, the S Trac was $995 and the REM and EDM polished 3:89 Motive gears from C&R Racing but I don't remember what I paid for them.

I'll check it out, appreciate the info