Bumper guard mounting question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BigRed76 · 01-15-2016, 12:26 AM

I've been thinking about getting a pair of front bumper guards for my GMC, the short style like pictured, but I'd like to know how they mount to the bumper. I would want to mount them using the inside bumper bolts, but I don't really want to drill any extra holes in the bumper if that's how they mount. Any input is appreciated, thanks

68panelman · 01-15-2016, 01:02 PM

I installed bumper guards this past spring using the existing lower frame bumper bolts. I too did not want to drill into my bumpers. There will be a small gap between the two, but I'm talking about 1/8". Be sure to not over tighten.

BigRed76 · 01-17-2016, 01:40 AM

Quote:

Originally Posted by 68panelman

I installed bumper guards this past spring using the existing lower frame bumper bolts. I too did not want to drill into my bumpers. There will be a small gap between the two, but I'm talking about 1/8". Be sure to not over tighten.

Thanks for the info. And just using the lower bolt was enough to sufficiently hold them on?

sboris · 01-17-2016, 07:28 AM

That along with a little bracket or clamp at the top. Goes over the top of the bumper.

BigRed76 · 01-17-2016, 08:13 PM

Quote:

Originally Posted by sboris

That along with a little bracket or clamp at the top. Goes over the top of the bumper.

I do remember seeing some hook type hardware shown with new bumper guards online, is that what you're referring to?

68panelman · 01-17-2016, 08:18 PM

The upper bolt on the guard uses a clip bracket and bolt. Along with the lower frame bolt, it's going nowhere.

BigRed76 · 01-17-2016, 08:25 PM

Quote:

Originally Posted by 68panelman

The upper bolt on the guard uses a clip bracket and bolt. Along with the lower frame bolt, it's going nowhere.

Good to know. I'll be keeping an eye out for some oem guards then. Thanks

01-15-2016, 12:26 AM	#1
BigRed76 Registered User Join Date: Jan 2010 Location: Loveland, CO Posts: 1,921	Bumper guard mounting question I've been thinking about getting a pair of front bumper guards for my GMC, the short style like pictured, but I'd like to know how they mount to the bumper. I would want to mount them using the inside bumper bolts, but I don't really want to drill any extra holes in the bumper if that's how they mount. Any input is appreciated, thanks Attached Images __________________ Zach 1970 Chevrolet Custom Camper K20 1971 GMC Super K2500, 12V/NV4500 swap in progress 1971 Chevrolet Custom C10 1972 Chevrolet Custom Deluxe C20, 5.3/4L60E 1972 Oldsmobile Cutlass Supreme, 455/TH400, 3.73 posi 2004 GMC Sierra 2500HD, LB7/Allison, CCSB 2005 GMC Sierra 1500, 5.3/4L60E, CCSB

01-15-2016, 01:02 PM	#2
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,458	Re: Bumper guard mounting question I installed bumper guards this past spring using the existing lower frame bumper bolts. I too did not want to drill into my bumpers. There will be a small gap between the two, but I'm talking about 1/8". Be sure to not over tighten.

01-17-2016, 07:28 AM	#4
sboris Registered User Join Date: Jun 2011 Location: Osceola, Ia Posts: 2,017	Re: Bumper guard mounting question That along with a little bracket or clamp at the top. Goes over the top of the bumper. __________________ Shawn 68 chevy K/20 05 chevy 3/4 4x4 71 short step-sold 71 chevy Beauville van My build. http://67-72chevytrucks.com/vboard/s...d.php?t=633039

01-17-2016, 08:18 PM	#6
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,458	Re: Bumper guard mounting question The upper bolt on the guard uses a clip bracket and bolt. Along with the lower frame bolt, it's going nowhere.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.