OT: WTB or suggestions - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72superBB · 03-02-2004, 09:17 PM

I need a reaplacement 2 piece oil pressure line from the block to the oil pressure gauge.

Or

I need to knowwhat I can use to replace it. I bought an Autometer line, but the fittings would not attach to the factory gauge fitting.

Thanks

Ron Webb

**JDL** · 03-02-2004, 09:26 PM

you should be abale to find every thing you need at the local hardware store

72superBB · 03-02-2004, 11:01 PM

ttt

*botboy* · 03-03-2004, 02:11 AM

I have one, still on truck tho. If small block and big block lines are interchangeable it should fit fine. $15 shipped assuming I don't break it pulling it off sound good?

gonebad2 · 03-03-2004, 03:14 AM

If it's 1/8" copper tubing, go to the hardware store and tell them you need 1/8" brass breakaway ferrules. If the hardware store doesn't have them, go to an appliance repair store. Those are a very common fitting on gas appliances. They use them for a sense line on gas valves. I buy them in bulk at work and pay less than .05 ea.

72superBB · 03-03-2004, 04:37 PM

I found one. Thanks everyone.

Ron

03-02-2004, 09:17 PM	#1
72superBB Registered User Join Date: Nov 2003 Location: Mandan, ND Posts: 422	OT: WTB or suggestions I need a reaplacement 2 piece oil pressure line from the block to the oil pressure gauge. Or I need to knowwhat I can use to replace it. I bought an Autometer line, but the fittings would not attach to the factory gauge fitting. Thanks Ron Webb __________________ Life is full of choices and a Chevy is the best choice. 1990 Chevy SWB

03-02-2004, 09:26 PM	#2
JDL Senior Member Join Date: Sep 2000 Location: Agency IA. Posts: 1,884	you should be abale to find every thing you need at the local hardware store __________________ 72 Chevy short step side with 454 air and tilt. 72 nova project car 63 chevy II drag car Agency Iowa

03-02-2004, 11:01 PM	#3
72superBB Registered User Join Date: Nov 2003 Location: Mandan, ND Posts: 422	ttt __________________ Life is full of choices and a Chevy is the best choice. 1990 Chevy SWB

03-03-2004, 03:14 AM	#5
gonebad2 Merciless Butcher Join Date: Oct 2003 Location: CC Nevada Posts: 1,447	If it's 1/8" copper tubing, go to the hardware store and tell them you need 1/8" brass breakaway ferrules. If the hardware store doesn't have them, go to an appliance repair store. Those are a very common fitting on gas appliances. They use them for a sense line on gas valves. I buy them in bulk at work and pay less than .05 ea. __________________ Your Bought And Sold....I Got Your Soul! Last edited by gonebad2; 03-03-2004 at 03:17 AM.

03-03-2004, 04:37 PM	#6
72superBB Registered User Join Date: Nov 2003 Location: Mandan, ND Posts: 422	I found one. Thanks everyone. Ron __________________ Life is full of choices and a Chevy is the best choice. 1990 Chevy SWB

03-03-2004, 02:11 AM	#4
botboy Account Suspended Join Date: Dec 2003 Location: Delano, MN Posts: 630	I have one, still on truck tho. If small block and big block lines are interchangeable it should fit fine. $15 shipped assuming I don't break it pulling it off sound good?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.