Is this a '67 door handle? If so, WIW? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**nitrosport_5** · 06-11-2016, 11:48 PM

Hey guys, i have a NOS passenger door handle i purchased a while back. When going to install it on my truck, i noticed for one, the pushrod for the door opener is much too long, AND the bolts seem to go in straight instead of at an angle to match the door curve.

Here are some pics of the box, the handle, and the handle beside one i took off of a '70. I put those long bolts in them a couple turns to show the difference better. Handle on right is NOS, left is the '70. The box may or maynot be correct... i had purchased 2 different handles thinking they were driver and passwnger since numbers were close but not the same but they both ended up being passener side. I may have mixed them up comparing and picking the nicer chrome of the 2. Didnt even think to look at bolt holes or pushrod. Ill have to get the numbers and picture of the other handle when i get home tomorrow evening.

**nitrosport_5** · 06-11-2016, 11:54 PM

3927898 is the other handle box part number. Just looked it up from when i purchased it.

**michael bustamante** · 07-06-2016, 12:15 PM

isint that longer pin for the suburban door?

**nitrosport_5** · 07-06-2016, 02:43 PM

Quote:

Originally Posted by michael bustamante

isint that longer pin for the suburban door?

from what i can find, it is meant to be trimmed down when used on a regular truckndoor, left long for the burb rear door

06-11-2016, 11:48 PM	#1
nitrosport_5 Registered User Join Date: Jul 2012 Location: St. John, Washington Posts: 618	Is this a '67 door handle? If so, WIW? Hey guys, i have a NOS passenger door handle i purchased a while back. When going to install it on my truck, i noticed for one, the pushrod for the door opener is much too long, AND the bolts seem to go in straight instead of at an angle to match the door curve. Here are some pics of the box, the handle, and the handle beside one i took off of a '70. I put those long bolts in them a couple turns to show the difference better. Handle on right is NOS, left is the '70. The box may or maynot be correct... i had purchased 2 different handles thinking they were driver and passwnger since numbers were close but not the same but they both ended up being passener side. I may have mixed them up comparing and picking the nicer chrome of the 2. Didnt even think to look at bolt holes or pushrod. Ill have to get the numbers and picture of the other handle when i get home tomorrow evening. Attached Images __________________ "Rusty" 1972 K20 Cheyenne Super, 496, A/C, Tilt, Tach, Buckets, 4l80e/NP205, 4" Rancho Lift, 35" BFG AT "Ramp Truck" 1972 C30 Ramp Truck 350, Air Bags, Factory A/C. "1968" C10 Shortbed project

06-11-2016, 11:54 PM	#2
nitrosport_5 Registered User Join Date: Jul 2012 Location: St. John, Washington Posts: 618	Re: Is this a '67 door handle? If so, WIW? 3927898 is the other handle box part number. Just looked it up from when i purchased it. __________________ "Rusty" 1972 K20 Cheyenne Super, 496, A/C, Tilt, Tach, Buckets, 4l80e/NP205, 4" Rancho Lift, 35" BFG AT "Ramp Truck" 1972 C30 Ramp Truck 350, Air Bags, Factory A/C. "1968" C10 Shortbed project

07-06-2016, 12:15 PM	#3
michael bustamante Senior Member Join Date: Sep 2007 Location: Albuquerque NM Posts: 7,862	Re: Is this a '67 door handle? If so, WIW? isint that longer pin for the suburban door? __________________ 1967custom



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.