|
11-01-2016, 06:22 PM
|
#1 |
|
Registered User
Join Date: May 2016
Location: Houston texas
Posts: 51
|
Ls motor mounts
Anybody have any experience with LSX Innovations motor mounts for ls swap ?
|
|
|
|
11-01-2016, 07:16 PM
|
#2 |
|
Registered User
Join Date: Oct 2013
Location: Alabama
Posts: 1,234
|
Re: Ls motor mounts
stock towers with stock motor mounts on dirty dingo sliders. never understood why folks buy these high dollar "conversion" mounts when stock works fine. <shrug>
|
|
|
|
|
11-01-2016, 07:48 PM
|
#3 |
|
Registered User
Join Date: May 2016
Location: Houston texas
Posts: 51
|
Re: Ls motor mounts
These are very similar to the dirty dingo sliders except cheaper. Uses the stock stuff . THEY are bit cheaper then
DD sliders . |
|
|
|
|
11-01-2016, 09:50 PM
|
#4 | |
|
Senior Member
 
Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,237
|
Re: Ls motor mounts
Quote:
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
|
|
|
|
|
11-02-2016, 09:59 AM
|
#5 |
|
Registered User
Join Date: Aug 2016
Location: KC(ish)
Posts: 6
|
Re: Ls motor mounts
http://www.ebay.com/itm/LS-Swap-Kit-...-/201607117697
These are the ones I bought on recommendation in another post here. Can't comment on fitment yet but do appear well made. Not what I would consider high dollar. |
|
|
|
|
11-02-2016, 04:24 PM
|
#6 |
|
Registered User
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
|
Re: Ls motor mounts
Those are what I used on mine. Though the DD Sliders would have more infinite positioning options, the 3 position mounts work fine. I did have to move my stock engine stands to the 6 cylinder position to get the motor back as far as I wanted, plus drill a new hole for the lower engine stand bolt. That's an easy part of the swap though.
__________________
-Duane C/10 Club Texas member 1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project) 1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby) |
|
|
|
|
11-02-2016, 10:01 PM
|
#7 |
|
Registered User
Join Date: May 2016
Location: Houston texas
Posts: 51
|
Re: Ls motor mounts
Thanks guys for the replies. Those are the ones I was looking at. Was hoping not to change the bell housing position so I wouldn't have to chang driveshaft.
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
