The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-25-2016, 07:32 PM   #1
dmjlambert
Senior Member
 
dmjlambert's Avatar
 
Join Date: Apr 2016
Location: Cypress, TX
Posts: 3,860
Electric connectors needed for 69 CST/10

Hi, I have a 69 CST/10 with 350 SBC, factory A/C (non-working now but I hope to get it working), and a gauge cluster.

I would like to ask if anybody has leftover parts from a wiring harness or access to a salvaged harness, and may be able to provide me some parts? My electric harness is in pretty good condition, except for these 2 parts:
AC Blower motor switch connector (mine is melted)
Connector to compressor (mine is duct-taped)

Also:

Pin 5 of my instrument cluster connector is not occupied. That is the way it was made because I have a gauge cluster. But I would like one of these terminals that has been removed from a cluster connector, or a whole cluster connector. That pin 5 goes to a working TEMP light and I would like make that light work on my truck, using an indicator-light-type temperature sensor installed on the passenger side of the engine.

I would like to ask if anybody knows about the part I am pointing to with the arrow on the AC compressor connector? It looks like perhaps it is a diode. I'm not sure if that was integrated with the old connector or added by somebody for some reason. I don't see it on the wiring diagram.

So, my want-to-buy list is:
AC Blower motor switch connector
Compressor connector
Cluster connector or a terminal removed from a cluster connector
Attached Images
   
dmjlambert is offline   Reply With Quote
Old 11-25-2016, 08:58 PM   #2
57taskforce
All about them K’s
 
57taskforce's Avatar
 
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,490
Re: Electric connectors needed for 69 CST/10

I most likely have what you need, may or may not have the compressor connector but I have the others.
__________________
Tyler
'57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888
'72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879
‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206
'98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s
57taskforce is offline   Reply With Quote
Old 11-25-2016, 09:26 PM   #3
FirstOwner69
Senior Member
 
FirstOwner69's Avatar
 
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,852
Re: Electric connectors needed for 69 CST/10

Quote:
Originally Posted by dmjlambert View Post
I would like to ask if anybody knows about the part I am pointing to with the arrow on the AC compressor connector? It looks like perhaps it is a diode. I'm not sure if that was integrated with the old connector or added by somebody for some reason. I don't see it on the wiring diagram.
That is correct. It came that way from GM. If I recall correctly mine was wrapped with electrical tape that started on the connector and went just far enough to cover whatever that is since the truck was new.
FirstOwner69 is offline   Reply With Quote
Old 11-26-2016, 12:09 AM   #4
dmjlambert
Senior Member
 
dmjlambert's Avatar
 
Join Date: Apr 2016
Location: Cypress, TX
Posts: 3,860
Re: Electric connectors needed for 69 CST/10

Quote:
Originally Posted by 57taskforce View Post
I most likely have what you need, may or may not have the compressor connector but I have the others.
Thanks very much, that sounds good. I'll PM you to discuss the details.

Quote:
Originally Posted by FirstOwner69 View Post
That is correct. It came that way from GM. If I recall correctly mine was wrapped with electrical tape that started on the connector and went just far enough to cover whatever that is since the truck was new.
Thanks for that info. I think I'll take the duct tape off and clean it up and see what I can do about wrapping it properly. I just got a role of that non-adhesive black vinyl tape. That must be a flyback diode to reduce EMF and reduce arcing on the compressor switch.
dmjlambert is offline   Reply With Quote
Old 11-26-2016, 01:05 AM   #5
57taskforce
All about them K’s
 
57taskforce's Avatar
 
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,490
Re: Electric connectors needed for 69 CST/10

Pm returned.
__________________
Tyler
'57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888
'72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879
‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206
'98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s
57taskforce is offline   Reply With Quote
Reply

Bookmarks

Tags
blower, compressor, connector, switch, want to buy


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:22 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com