The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-27-2017, 03:51 PM   #1
II_Slow
Registered User
 
II_Slow's Avatar
 
Join Date: Jan 2012
Location: Celeste, Tx
Posts: 266
Tail Light Mounting, Chrome conduit

I bought new tail lights and the chrome conduit for my 2nd gen 55. The connector on the back of the tail light housing comes straight out the back, and the chrome conduit simply will not bent enough to stay off of the fenders.
I'm sure pleny of others have had this problem, so surely there is a simple solution. I saw a couple routed through the fender, but I don't to drill the fenders for that. I tried using the boot from the wiring kit which is only about 45 degrees - helped a little but not near enough?
Am I missing something here? I suppose I could raise the lights up in the stake pocket or space them forward. Any suggestions for a true 90 boot or other option?

If I slip the chrome conduit directly over the connector, I have to bend it so sharply it breaks.
__________________
1955 SB Stepside 3100 big window cab on a 99 Ram 2500 Frame w/ 12-V Cummins diesel power and
47RH AOD transmission
http://67-72chevytrucks.com/vboard/s...d.php?t=640042
II_Slow is offline   Reply With Quote
Old 01-27-2017, 04:31 PM   #2
Dan in Pasadena
Senior Member

 
Dan in Pasadena's Avatar
 
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,343
Re: Tail Light Mounting, Chrome conduit

Just spitballing here (because I am going to have the same problem soon!)

How about looking for a chrome 90* elbow that will replace these boots in the plumbing department of your local big box store? I would think exposed faucet plumbing would need a 90* sometimes.
__________________
'55 Big Window Shortbed,
Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's

Dan's '55 Big Window "Build" - Well, Kinda!
Dan in Pasadena is offline   Reply With Quote
Old 01-27-2017, 06:57 PM   #3
Russell Ashley
Registered User
 
Russell Ashley's Avatar
 
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,648
Re: Tail Light Mounting, Chrome conduit

I think most people route it horizontally and either go under the bed side or drill a hole and route it through the hole. Is that flexible metal cover specifically for that?
Russell Ashley is offline   Reply With Quote
Old 01-28-2017, 08:04 AM   #4
1project2many
Registered User
 
Join Date: Mar 2012
Location: Lakes Region NH
Posts: 3,200
Re: Tail Light Mounting, Chrome conduit

Quote:
Any suggestions for a true 90 boot or other option?
Spark plug wire boot? 90 degree vacuum fitting? PVC or ABS pipe fitting?

Drill hole in bottom of light and route wires vertically, use plug in hole in rear of light?

90 degree boot made for flexible conduit?
http://leinuoer.en.alibaba.com/produ...e_conduit.html
1project2many is offline   Reply With Quote
Old 01-28-2017, 12:53 PM   #5
my56chevytruck
Registered User
 
my56chevytruck's Avatar
 
Join Date: Feb 2016
Location: Hebron
Posts: 1,153
Re: Tail Light Mounting, Chrome conduit

Just a thought, do you have enough conduit to go over the top and come down to your light?? seems that there's more room topside??
__________________
RUBBER DOWN AND HIT THE ROAD!!!
1940 Ford Dlx Coupe
1969 Mach1
my56chevytruck is offline   Reply With Quote
Old 01-28-2017, 01:30 PM   #6
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,710
Re: Tail Light Mounting, Chrome conduit

I'd follow Dan's suggestion first and head to the local big box hardware or the local has everything plumbing store with the conduit and maybe even the taillight in hand.

This might let you sort out and figure out what you are hunting for
https://www.plumbingsupply.com/chrome.html

Half of hunting for something is knowing what you are asking for when you go hunting.
you may be drilling and tapping and putting in set screws to make it work.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 01-28-2017, 01:47 PM   #7
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,670
Re: Tail Light Mounting, Chrome conduit

Could you swap the mounting brackets from left side to right?..that would flip them over and put the hole on the top side of the bracket and might give you a little more room..

Last edited by mongocanfly; 01-28-2017 at 01:52 PM.
mongocanfly is offline   Reply With Quote
Old 01-28-2017, 02:51 PM   #8
capnduane
Registered User
 
capnduane's Avatar
 
Join Date: Jan 2014
Location: Moreno Valley, Calif.
Posts: 244
Re: Tail Light Mounting, Chrome conduit

On my truck I just put heat shrink tubing over the plugs and wiring tube that came with the tail lights. My mounting brackets are straight, so I look to have more room between tail lights and fender also.
Attached Images
 
__________________
'55 Chevy 1/2ton pickup w/ Pontiac 350 and Muncie M21 close ratio 4speed "Red Ryder"
capnduane is offline   Reply With Quote
Old 01-29-2017, 12:04 AM   #9
1958Warrior
Registered User
 
1958Warrior's Avatar
 
Join Date: Mar 2013
Location: Mesquite,Tx
Posts: 416
Re: Tail Light Mounting, Chrome conduit

To use what you've got ,best option would be to mount them higher, another option would be to use some braided S.S. wire loom with some heat shrink on the ends.
http://www.ebay.com/itm/5-FEET-Braid...-/250907462515

I cant remember who it was , but one of the guys used a piece of SS tubing and bent it to use as conduit.
It was Youngrodder post #6 here
http://www.67-72chevytrucks.com/vboa...ht=tail+lights

A 90* boot to look at to see if it would fit comes to mind ...A spark plug boot for a lawn mower might work ...

Heat shrink would look good too. Might just want to run it to keep it tight to the bracket for a cleaner look.But nothing wrong with the way Capnduane ran his ,but if yours will be lower the wires will be less noticeable .

Last edited by 1958Warrior; 01-29-2017 at 12:18 AM.
1958Warrior is offline   Reply With Quote
Old 01-29-2017, 07:56 PM   #10
II_Slow
Registered User
 
II_Slow's Avatar
 
Join Date: Jan 2012
Location: Celeste, Tx
Posts: 266
Re: Tail Light Mounting, Chrome conduit

I really like the polished SS solution that YoungRodder did. I should be able to find some scrap SS tubing at work. Thanks for the link!
__________________
1955 SB Stepside 3100 big window cab on a 99 Ram 2500 Frame w/ 12-V Cummins diesel power and
47RH AOD transmission
http://67-72chevytrucks.com/vboard/s...d.php?t=640042
II_Slow is offline   Reply With Quote
Old 01-29-2017, 11:13 PM   #11
youngrodder
Registered User
 
youngrodder's Avatar
 
Join Date: Mar 2007
Location: Scotts, Michigan
Posts: 3,774
Re: Tail Light Mounting, Chrome conduit

Quote:
Originally Posted by II_Slow View Post
I really like the polished SS solution that YoungRodder did. I should be able to find some scrap SS tubing at work. Thanks for the link!
Yes I originally purchased some of the flexible conduit kind like you did and was unhappy with them. I did go through some SS tubing until I figured out a simple clean way to run it...

Marc
__________________
…………...........__________
.................. ((__|__||___\____
..;.;;.:;:;.,;..;((_(O))____ (_(O))

1948 Chevy Truck - Finished SOLD!!

1953 Chevy Suburban "Family Truckster" Completed: Spring of 2021
http://67-72chevytrucks.com/vboard/s...d.php?t=605484

1994 4x4 Blazer - "Field Find"
https://67-72chevytrucks.com/vboard/...ferrerid=30857
youngrodder is offline   Reply With Quote
Old 01-29-2017, 11:47 PM   #12
Dan in Pasadena
Senior Member

 
Dan in Pasadena's Avatar
 
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,343
Re: Tail Light Mounting, Chrome conduit

Some ideas I have taken pictures of at various shows:


Thought i had more, but i guess not. I saw one that was hardlined with polished stainless tube like this rubber one. Looked very clean.
__________________
'55 Big Window Shortbed,
Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's

Dan's '55 Big Window "Build" - Well, Kinda!

Last edited by Dan in Pasadena; 01-29-2017 at 11:56 PM.
Dan in Pasadena is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:32 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com