|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-28-2017, 05:23 PM
|
#1 |
|
Registered User
Join Date: Aug 2017
Location: Eugene Oregon
Posts: 128
|
glove box takes two hands to open, is something installed wrong?
ideally I would push the button and the door would just fall open but instead i have to grab the side of the glove box door with the other hand to pull it open... do I have something installed incorrectly? Is there something I can adjust to get it to fall?
__________________
1977 SWB (c20 conversion) SBC350 Springfield Oregon Instagram: @nevernotchevy |
|
|
|
12-28-2017, 05:51 PM
|
#2 |
|
Restoring it $200 at a time...
Join Date: Aug 2008
Location: NE Kansas
Posts: 892
|
Re: glove box takes two hands to open, is something installed wrong?
You're missing the bumpers that pop the door when the latch is released. At the upper corners of the glove box opening, you'll see about a 3/16" hole in the dash panel. New parts are like $1/pr at your favorite parts supplier.
__________________
Charter member of the 'Put the dimmer switch back on the damn floor where it belongs' Society '68 5.3L-4 speed LWB C20; grandpa bought it for the farm in '71. Now LS 5.3, rather than 327. DD '09 Pilot Weekender '65 Skylark 300-4V-4 speed Wife's '07 Lexus ES350; 117 actuator motors and I can't see the engine. Son's '04 F250 SuperCab 6.0 |
|
|
|
|
12-28-2017, 05:53 PM
|
#3 |
|
The Older Generation
   
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,891
|
Re: glove box takes two hands to open, is something installed wrong?
-
There is also a torsion spring integrated with the hinge. It runs the length of the hinge.... LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
12-28-2017, 06:51 PM
|
#4 |
|
Registered User
Join Date: May 2016
Location: Henderson NC
Posts: 975
|
Re: glove box takes two hands to open, is something installed wrong?
Oil the hinge.
|
|
|
|
|
12-28-2017, 08:09 PM
|
#5 |
|
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: glove box takes two hands to open, is something installed wrong?
I've seen latches not release fully from being dry.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
12-28-2017, 08:22 PM
|
#6 |
|
Registered User
Join Date: Aug 2017
Location: Eugene Oregon
Posts: 128
|
Re: glove box takes two hands to open, is something installed wrong?
I think hounddogs is right.. I see the holes and no bumpers are in so I ordered a few. Thanks!
__________________
1977 SWB (c20 conversion) SBC350 Springfield Oregon Instagram: @nevernotchevy |
|
|
|
|
12-28-2017, 08:25 PM
|
#7 |
|
Moderator
Join Date: May 2007
Location: Southern Cal
Posts: 20,058
|
Re: glove box takes two hands to open, is something installed wrong?
MAke sure the swing arm isn’t bent and hanging up. If so it’s easy to bend back for clearance.
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
|
12-29-2017, 12:37 PM
|
#8 |
|
Registered User
Join Date: May 2011
Location: Fort Pierce, FL
Posts: 430
|
Re: glove box takes two hands to open, is something installed wrong?
There is some adjustment on the latch too. I used to have to really slam mine, and I put up with it for way too long. After adjustment it closed perfectly, although my wife forgets and still slams it!
|
|
|
|
|
01-02-2018, 06:31 PM
|
#9 |
|
Registered User
Join Date: Aug 2017
Location: Eugene Oregon
Posts: 128
|
Re: glove box takes two hands to open, is something installed wrong?
It was the bumpers! Ordered two on eBay and it falls open perfectly.. thanks everyone!
__________________
1977 SWB (c20 conversion) SBC350 Springfield Oregon Instagram: @nevernotchevy |
|
|
|
|
01-02-2018, 08:01 PM
|
#10 |
|
Registered User
Join Date: Dec 2012
Location: Vancouver, Washington
Posts: 1,644
|
Re: glove box takes two hands to open, is something installed wrong?
I love happy endings to issues! Will have to see what’s up with mine.
__________________
1968 Chevrolet C/10 LWB - 327, TH350 - 4/5 Drop |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
