Door molding channel - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**8man** · 09-11-2018, 04:45 PM

What is the preferred way to remove the door channel that holds the door molding? I need to work on the dash of the 54 and need to remove some of the channel.

Is there a replacement channel available if I mess it up?

**joedoh** · 09-12-2018, 12:02 AM

I think I saw that on the bowtiebits site the other day.

http://www.bowtiebits.com/store/stor...Category_ID=27

says that it is spot welded in place.

MARTINSR · 09-12-2018, 01:27 AM

I have to save that, don't know what I am going to use. I have a set of the stock 48 retainers, but I don't know what I will use.

Brian

**8man** · 09-12-2018, 11:01 AM

Thanks Joe, that is what I was looking for.

I didn't know the correct name again, so it didn't pop up when I was looking. Of course, I didn't go to Bowtie bits site, but I did try Ecklers and Chevs of the 40's.

**joedoh** · 09-13-2018, 12:45 AM

I didnt know the name either, I just tripped over those browsing the site haha

09-11-2018, 04:45 PM	#1
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Door molding channel What is the preferred way to remove the door channel that holds the door molding? I need to work on the dash of the 54 and need to remove some of the channel. Is there a replacement channel available if I mess it up?

09-12-2018, 12:02 AM	#2
joedoh Senior Member Join Date: May 2007 Location: Doodah Kansas Posts: 7,774	Re: Door molding channel I think I saw that on the bowtiebits site the other day. http://www.bowtiebits.com/store/stor...Category_ID=27 says that it is spot welded in place. __________________ the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393

09-12-2018, 01:27 AM	#3
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: Door molding channel I have to save that, don't know what I am going to use. I have a set of the stock 48 retainers, but I don't know what I will use. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

09-12-2018, 11:01 AM	#4
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Door molding channel Thanks Joe, that is what I was looking for. I didn't know the correct name again, so it didn't pop up when I was looking. Of course, I didn't go to Bowtie bits site, but I did try Ecklers and Chevs of the 40's.

09-13-2018, 12:45 AM	#5
joedoh Senior Member Join Date: May 2007 Location: Doodah Kansas Posts: 7,774	Re: Door molding channel I didnt know the name either, I just tripped over those browsing the site haha __________________ the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.