Crossmember swap woes.72 clip into 64 c10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

capriceutah · 09-18-2018, 10:56 PM

Guys and Girls,

I pulled my crossmember out of my 64 c10 to swap to a rebuilt setup for a 72.

When I pulled all of the bolts on the 64 c10 crossmember, it didn't just drop out of the truck. I had to pry it a little.. not hard but a little. Now I'm trying to swap the 72 in and I cant get it to slide in. It's like the frame where the crossmember bolts in is like 1/4 inch too wide.

Has anyone run into this before(I'm sure someone has) and what are my options?

Thank you for all of your help!

Chris

**Captainfab** · 09-19-2018, 12:07 AM

Just use a bar clamp or maybe a couple of ratchet straps to squeeze the frame together a little.

capriceutah · 09-19-2018, 07:14 PM

Quote:

Originally Posted by Captainfab

Just use a bar clamp or maybe a couple of ratchet straps to squeeze the frame together a little.

Perfect! Thanks for the response.. Cant wait to get the brackets installed!

Chris

capriceutah · 09-22-2018, 10:58 PM

Captainfab,

Your strap suggestion worked like a champ!

Thanks,
Chris

BabyBlue64 · 09-29-2018, 02:55 PM

Can someone tell me if it is possible to use a crossmember out of an '82 suburban with diesel engine under my '64 with straight 6? Or do I get problems with my motormounts?

**Chevy Fleetside** · 09-29-2018, 03:49 PM

Quote:

Originally Posted by BabyBlue64

Can someone tell me if it is possible to use a crossmember out of an '82 suburban with diesel engine under my '64 with straight 6? Or do I get problems with my motormounts?

You really don't need to do that unless your cross member is bent or something. The later control arms will bolt up to the early cross member.

**Captainfab** · 09-30-2018, 12:07 AM

That is true unless the '64 in question is a C20.

Quote:

Originally Posted by Chevy Fleetside

You really don't need to do that unless your cross member is bent or something. The later control arms will bolt up to the early cross member.

**Captainfab** · 09-30-2018, 12:10 AM

While I have not swapped the suspension crossmember under a truck with a I6, the engine mounts should bolt in. If not, worst case you may have to drill the holes in the crossmember for the lower bolt of the engine mount brackets.

Quote:

Originally Posted by BabyBlue64

Can someone tell me if it is possible to use a crossmember out of an '82 suburban with diesel engine under my '64 with straight 6? Or do I get problems with my motormounts?

**Chevy Fleetside** · 09-30-2018, 10:37 AM

Quote:

Originally Posted by Captainfab

That is true unless the '64 in question is a C20.

yes.. I am going on the assumption that it is a C 10. I will have to mention that if I ever put my 2 cents in next time.

BabyBlue64 · 09-30-2018, 11:05 AM

Thank you Guy's for the info. My truck is a C10. I didn't knew the newer A arms just bolt on the older crossmember. I want to use the diskbrakes of the Burb onder mine.

**Captainfab** · 09-30-2018, 11:28 PM

And you don't have to change the control arms either. You can simply change the upper and lower ball joints to the later model ball joints for the disc brake spindle.

Quote:

Originally Posted by BabyBlue64

Thank you Guy's for the info. My truck is a C10. I didn't knew the newer A arms just bolt on the older crossmember. I want to use the diskbrakes of the Burb onder mine.

**Chevy Fleetside** · 10-02-2018, 09:21 AM

Quote:

Originally Posted by Captainfab

And you don't have to change the control arms either. You can simply change the upper and lower ball joints to the later model ball joints for the disc brake spindle.

http://www.67-72chevytrucks.com/vboa...isc+brake+swap Yep. I did that to mine. Well one of mine and they work just fine.

09-18-2018, 10:56 PM	#1
capriceutah Registered User Join Date: Oct 2007 Location: Midvale, UT Posts: 40	Crossmember swap woes.72 clip into 64 c10 Guys and Girls, I pulled my crossmember out of my 64 c10 to swap to a rebuilt setup for a 72. When I pulled all of the bolts on the 64 c10 crossmember, it didn't just drop out of the truck. I had to pry it a little.. not hard but a little. Now I'm trying to swap the 72 in and I cant get it to slide in. It's like the frame where the crossmember bolts in is like 1/4 inch too wide. Has anyone run into this before(I'm sure someone has) and what are my options? Thank you for all of your help! Chris

09-19-2018, 12:07 AM	#2
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Crossmember swap woes.72 clip into 64 c10 Just use a bar clamp or maybe a couple of ratchet straps to squeeze the frame together a little. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

09-22-2018, 10:58 PM	#4
capriceutah Registered User Join Date: Oct 2007 Location: Midvale, UT Posts: 40	Re: Crossmember swap woes.72 clip into 64 c10 Captainfab, Your strap suggestion worked like a champ! Thanks, Chris

09-29-2018, 02:55 PM	#5
BabyBlue64 Registered User Join Date: Dec 2016 Location: Noordwijkerhout, Netherlands Posts: 56	Re: Crossmember swap woes.72 clip into 64 c10 Can someone tell me if it is possible to use a crossmember out of an '82 suburban with diesel engine under my '64 with straight 6? Or do I get problems with my motormounts?

09-30-2018, 11:05 AM	#10
BabyBlue64 Registered User Join Date: Dec 2016 Location: Noordwijkerhout, Netherlands Posts: 56	Re: Crossmember swap woes.72 clip into 64 c10 Thank you Guy's for the info. My truck is a C10. I didn't knew the newer A arms just bolt on the older crossmember. I want to use the diskbrakes of the Burb onder mine.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.