ls3 swap 4l60e hits floor - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67 stable · 10-22-2019, 08:13 AM

ls3 4l60e swap, transmissor hits floor, engine has a 8 Degree rake
stock oil pan, suspension drop. trans dept motor mounts.
any way to lower transmission from hitting floor ?

ls1nova71 · 10-22-2019, 09:24 AM

Stock LS3 oil pan? Those usually wont work on a truck, so maybe the engine is too high?

**PGSigns** · 10-22-2019, 11:57 AM

Ok 8 degrees in reference to what and that trans should clear the floor. Pictures would be a big help.
Jimmy

**mongocanfly** · 10-22-2019, 01:07 PM

(Hitting the floor).....do you mean floorboard of truck?
(8 degs rake)....is your frame level..0 degs.... and your driveline is 8 deg down in the rear ....is this what your sayin?
If your already at 8 deg down in the rear that's to much ..should be around 3 deg downward angle...but it needs to match the differential upward angle...what is your diff angle when the truck is sitting on all 4s?
You may need to do a trans tunnel or lower engine
Like said some pics will help as well as what your putting it in..

prodjay10 · 10-22-2019, 02:16 PM

Which perch/motor mount/ adapter setup you using? What’s this going in?

**Captainfab** · 10-22-2019, 11:10 PM

Knowing the year of truck would help with giving possible solutions.

67 stable · 10-22-2019, 11:57 PM

its a 67 c-10

Ghost's68 · 10-23-2019, 01:34 AM

I’ve got a 68 I LS swapped an LS3 and 4L80, running CPP engine mounts, DD sliders and stock trans mount I think I was roughly 4.5* down slope. 8 sounds high.

67 stable · 10-23-2019, 08:49 AM

can anyone recommend a oil pan swap ?
Okay i think i might have figured out the clearance problem.
we used the rear ( six cylinder) engine mount holes, because of the oil pan clearance.
we can movie the engine forward, that might level it out, but i don't see how it will lower the tranny.
how do you upload pics ?

**mongocanfly** · 10-23-2019, 01:42 PM

http://67-72chevytrucks.com/vboard/s...sting+pictures

**mongocanfly** · 10-23-2019, 01:43 PM

For pics...
http://67-72chevytrucks.com/vboard/s...sting+pictures

67 stable · 12-09-2019, 10:53 PM

Quote:

Originally Posted by Ghost's68

I’ve got a 68 I LS swapped an LS3 and 4L80, running CPP engine mounts, DD sliders and stock trans mount I think I was roughly 4.5* down slope. 8 sounds high.

Installed the holley 302-2 oil pan and moved the engine two inches forward to the v-8 holes, a lot of clearance but still sits raked and tranny hit floor
using the trans depot engine mount and stock frame mount
anyway to lower the engine with different mounts ?

prodjay10 · 12-09-2019, 11:22 PM

I used the stock v8 perches in the v8 position with 1 inch set back plates and it doesn’t hit floor. Truck oil pan. I have a couple inches of clearance between tunnel and transmission. Angle is close but I have space to dial it in.

With a 1 inch setback the engine is in the same spot as a 350. I will be using another set of adapter plates so I can do a 2 inch setback to be able to use the original driveshaft. As it is, the yoke is not as far in as I’d like.
Posted via Mobile Device

prodjay10 · 12-09-2019, 11:25 PM

This is in a 1971 c10 with a low hump.

prodjay10 · 12-10-2019, 10:31 AM

Looks like these mounts make your engine sit too high. Same thing happened to me with the square body c20 mounts.

10-22-2019, 08:13 AM	#1
67 stable Registered User Join Date: Sep 2018 Location: idaho Posts: 11	ls3 swap 4l60e hits floor ls3 4l60e swap, transmissor hits floor, engine has a 8 Degree rake stock oil pan, suspension drop. trans dept motor mounts. any way to lower transmission from hitting floor ? Last edited by 67 stable; 10-22-2019 at 08:15 AM. Reason: adding

10-22-2019, 09:24 AM	#2
ls1nova71 Registered User Join Date: Dec 2009 Location: Independence Mo Posts: 4,119	Re: ls3 swap 4l60e hits floor Stock LS3 oil pan? Those usually wont work on a truck, so maybe the engine is too high? __________________ My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html

10-22-2019, 11:57 AM	#3
PGSigns Senior Member Join Date: Jan 2011 Location: Hayes Va Posts: 4,569	Re: ls3 swap 4l60e hits floor Ok 8 degrees in reference to what and that trans should clear the floor. Pictures would be a big help. Jimmy __________________ 60 to 66 Chevy and GMC window decals http://67-72chevytrucks.com/vboard/s...d.php?t=661131 Good friends, good food and a hotrod what else do you need? 1966 BBW long fleet Daily driver 1965 BBW short fleet Sold and going to a good home 1965 Suburban 2003 3500 Duramax 2005 Ultra Classic

10-22-2019, 01:07 PM	#4
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: ls3 swap 4l60e hits floor (Hitting the floor).....do you mean floorboard of truck? (8 degs rake)....is your frame level..0 degs.... and your driveline is 8 deg down in the rear ....is this what your sayin? If your already at 8 deg down in the rear that's to much ..should be around 3 deg downward angle...but it needs to match the differential upward angle...what is your diff angle when the truck is sitting on all 4s? You may need to do a trans tunnel or lower engine Like said some pics will help as well as what your putting it in.. __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

10-22-2019, 02:16 PM	#5
prodjay10 Registered User Join Date: Jun 2016 Location: Phoenix AZ Posts: 429	Re: ls3 swap 4l60e hits floor Which perch/motor mount/ adapter setup you using? What’s this going in?

10-22-2019, 11:10 PM	#6
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: ls3 swap 4l60e hits floor Knowing the year of truck would help with giving possible solutions. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

10-22-2019, 11:57 PM	#7
67 stable Registered User Join Date: Sep 2018 Location: idaho Posts: 11	Re: ls3 swap 4l60e hits floor its a 67 c-10

10-23-2019, 01:34 AM	#8
Ghost's68 Registered User Join Date: Jun 2016 Location: American Canyon, CA Posts: 253	Re: ls3 swap 4l60e hits floor I’ve got a 68 I LS swapped an LS3 and 4L80, running CPP engine mounts, DD sliders and stock trans mount I think I was roughly 4.5* down slope. 8 sounds high.

10-23-2019, 08:49 AM	#9
67 stable Registered User Join Date: Sep 2018 Location: idaho Posts: 11	Re: ls3 swap 4l60e hits floor can anyone recommend a oil pan swap ? Okay i think i might have figured out the clearance problem. we used the rear ( six cylinder) engine mount holes, because of the oil pan clearance. we can movie the engine forward, that might level it out, but i don't see how it will lower the tranny. how do you upload pics ?

10-23-2019, 01:42 PM	#10
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: ls3 swap 4l60e hits floor http://67-72chevytrucks.com/vboard/s...sting+pictures __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

10-23-2019, 01:43 PM	#11
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: ls3 swap 4l60e hits floor For pics... http://67-72chevytrucks.com/vboard/s...sting+pictures __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

12-09-2019, 11:22 PM	#13
prodjay10 Registered User Join Date: Jun 2016 Location: Phoenix AZ Posts: 429	I used the stock v8 perches in the v8 position with 1 inch set back plates and it doesn’t hit floor. Truck oil pan. I have a couple inches of clearance between tunnel and transmission. Angle is close but I have space to dial it in. With a 1 inch setback the engine is in the same spot as a 350. I will be using another set of adapter plates so I can do a 2 inch setback to be able to use the original driveshaft. As it is, the yoke is not as far in as I’d like. Posted via Mobile Device

12-09-2019, 11:25 PM	#14
prodjay10 Registered User Join Date: Jun 2016 Location: Phoenix AZ Posts: 429	Re: ls3 swap 4l60e hits floor This is in a 1971 c10 with a low hump.

12-10-2019, 10:31 AM	#15
prodjay10 Registered User Join Date: Jun 2016 Location: Phoenix AZ Posts: 429	Re: ls3 swap 4l60e hits floor Looks like these mounts make your engine sit too high. Same thing happened to me with the square body c20 mounts.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.