Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
02-15-2020, 12:55 PM | #1 |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
|
clicking in front drivers side 4X4 hub
Started to work on front hub, assembled with original bearings, now I have a click at the 3 o'clock, tightened first locking nut with no change. PO was in here and ground the bearing seats some what. wondering what the fix might be, starting with bearings or replace spindle
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
02-16-2020, 10:30 AM | #2 |
Senior Member
Join Date: Nov 2013
Location: East Tennessee
Posts: 2,199
|
Re: clicking in front drivers side 4X4 hub
I may be stating the obvious here...if so forgive me
the first spanner nut is the bearing adjustment nut....it should not be "tight" as it sets the correct pre-load on the bearings. The retaining washer....with all the holes...goes next to maintain the position of the first spanner nut. Then the outer "locking" spanner nut goes on.....it should be "tight" ...it keeps the hub fastened to the spindle.. As for the grinding....I don't know....have a picture?
__________________
1967 C10 Step side 1968 C10 Step side 1970 Chevrolet K/5 Blazer 1972 Chevrolet K/5 Blazer ............. |
02-16-2020, 10:42 AM | #3 |
Registered User
Join Date: Aug 2006
Location: LaSalle Mi
Posts: 525
|
Re: clicking in front drivers side 4X4 hub
There is more information and pictures in his build thread
https://67-72chevytrucks.com/vboard/...10641&page=129 |
02-16-2020, 12:36 PM | #4 | |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
|
Re: clicking in front drivers side 4X4 hub
Quote:
I've adjusted the preloads in and out, repacked bearings(these are used), talked to a shop, that has 50 years experiance, followed the Chilton manual to a 'T', it says to back off first nut almost 90 degrees. still has a click. So, you go back to the last thing you did, and I had rotors pressed on the hub, as I was laying the hub assembly on the ground, it didn't sound right, after further thought, I looked into the rotor, and it was loose on the hub, they used the old wheel studs, but it was only loose in one section. Now I'm on the search for correct wheel studs, and have them pressed in to see if that is the problem. My first thought was brearings, since that would be the cheapest fix first, but the most obvious thing points to the wheel studs The owner of the shop said the drivers side is the one he has seen the most problems with, since the rotation of the tire tends to loosen the spanner nut, he said to tighten the outside nut to 100 ft/lbs
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
|
02-16-2020, 01:20 PM | #5 |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
|
Re: clicking in front drivers side 4X4 hub
Thanks litebulblsc for posting up, wish I knew how to post a link
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
02-16-2020, 05:43 PM | #6 |
Registered User
Join Date: Aug 2006
Location: LaSalle Mi
Posts: 525
|
Re: clicking in front drivers side 4X4 hub
Just a simple copy and paste.
Highlight the site address, "right click" on it and click copy, then paste that in the reply area |
02-17-2020, 10:58 AM | #7 |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
|
Re: clicking in front drivers side 4X4 hub
spent some time to bolt up wheel and tire(100 ft/lbs) torque, spun the tire and no click, so the answer was rotor was not seated, onto lock out and finish up drivers side
removed wheel and tire and no clicking
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 02-17-2020 at 11:36 AM. |
02-17-2020, 11:42 AM | #8 |
Senior Member
Join Date: Nov 2013
Location: East Tennessee
Posts: 2,199
|
Re: clicking in front drivers side 4X4 hub
Glad to hear it was something simple...
__________________
1967 C10 Step side 1968 C10 Step side 1970 Chevrolet K/5 Blazer 1972 Chevrolet K/5 Blazer ............. |
Bookmarks |
|
|