The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-07-2020, 08:00 PM   #1
Ptjsk
Registered User
 
Join Date: Jan 2018
Location: Northern CA
Posts: 588
Gear Vendors Overdrive

After getting my Jimmy on the road, I was a bit concerned as to the drive-ability of the Truck.

I had rebuilt the motor, stroked it to a 383, and rebuilt both front and rear axles, as well as the 350 transmission.

Additionally, I installed Tru-trac posi units in both front and rear. Since I was going with 33" tires I thought 410 gear ratio would be the best.

After I finished I wasn't totally happy with trying to go 65 mph as the motor was rotating a bit above 3000 rpms.

I contemplated going with the overdrive transmission, but my transmission guy talked me into keeping the T350. He said they're just a great old (strong), transmission.

I began to look at the Gear Vendors for an overdrive unit. I probably had about a 50/50 response as to those saying it would work, and those saying it wouldn't work due to the short wheel-base.

Finally, I decided to take the plunge and just see for myself if it would work.

Then followed it up a Tom Woods driveline. These guys were super helpful and gave me guidance on rear end shims (6 degrees), and built a short driveline with a CV joint on the front end.

Happy to say, the Jimmy performs flawlessly! No vibration and most importantly, I can cruise along at 70-75 mph with no problems at all. The motors just cruising along now.

The only problem I have now is that I'll probably have to install one in the step-side!

Anybody have apprehensions with going this route need not worry. It will work!

Gear Vendors themselves are very helpful and can't say enough about Tom Woods drivelines!

Pat
Ptjsk is offline   Reply With Quote
Old 09-07-2020, 09:58 PM   #2
DeadheadNM
Carpe manana

 
DeadheadNM's Avatar
 
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,446
Re: Gear Vendors Overdrive

Great info. Thanks for posting. Pics when possible please.
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547
1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308

Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
DeadheadNM is offline   Reply With Quote
Old 09-08-2020, 12:42 AM   #3
Ptjsk
Registered User
 
Join Date: Jan 2018
Location: Northern CA
Posts: 588
Re: Gear Vendors Overdrive

Here you go!
Attached Images
  
Ptjsk is offline   Reply With Quote
Old 09-08-2020, 07:59 AM   #4
DeadheadNM
Carpe manana

 
DeadheadNM's Avatar
 
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,446
Re: Gear Vendors Overdrive

Very nice. How do you operate 4wd then if the GV unit services just the rear axle?
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547
1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308

Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
DeadheadNM is offline   Reply With Quote
Old 09-08-2020, 12:26 PM   #5
praisegeetarman
Registered User
 
Join Date: Feb 2010
Location: Harrah, Washington
Posts: 323
Re: Gear Vendors Overdrive

Quote:
Originally Posted by DeadheadNM View Post
Very nice. How do you operate 4wd then if the GV unit services just the rear axle?
With GV you use overdrive in 2 wheel drive only
__________________
71 Blazer 4X4 (unmolested, all original (including paint) 74,000 mile barn find)
67 Camaro RS SS (unmolested, all original (including paint) 81,000 mile barn find)

Keith Riel
praisegeetarman is offline   Reply With Quote
Old 09-08-2020, 02:47 PM   #6
DeadheadNM
Carpe manana

 
DeadheadNM's Avatar
 
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,446
Re: Gear Vendors Overdrive

Is there a switch then to activate the OD as desired?
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547
1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308

Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
DeadheadNM is offline   Reply With Quote
Old 09-08-2020, 03:03 PM   #7
jayoldschool
Moderator
 
Join Date: Dec 2012
Location: ON, Canada
Posts: 2,176
Re: Gear Vendors Overdrive

Quote:
Originally Posted by praisegeetarman View Post
With GV you use overdrive in 2 wheel drive only
I think it would have made more sense to go with a 4WD 4L60/65/80.
jayoldschool is offline   Reply With Quote
Old 09-09-2020, 11:20 AM   #8
praisegeetarman
Registered User
 
Join Date: Feb 2010
Location: Harrah, Washington
Posts: 323
Re: Gear Vendors Overdrive

Quote:
Originally Posted by DeadheadNM View Post
Is there a switch then to activate the OD as desired?
My buddy had one of these a while back. His used an actual old school dimmer switch on the floor in the stock location to activate the overdrive.
__________________
71 Blazer 4X4 (unmolested, all original (including paint) 74,000 mile barn find)
67 Camaro RS SS (unmolested, all original (including paint) 81,000 mile barn find)

Keith Riel
praisegeetarman is offline   Reply With Quote
Old 09-09-2020, 11:48 AM   #9
DeadheadNM
Carpe manana

 
DeadheadNM's Avatar
 
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,446
Re: Gear Vendors Overdrive

Thanks - I didn't realize the overdrive had an "on/off" switch so to speak. Doesn't seem like a bad way to go - probably less fuss involved than the 700R4 swap we did in my K20.
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547
1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308

Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
DeadheadNM is offline   Reply With Quote
Old 09-09-2020, 11:08 PM   #10
Ptjsk
Registered User
 
Join Date: Jan 2018
Location: Northern CA
Posts: 588
Re: Gear Vendors Overdrive

Quote:
Originally Posted by DeadheadNM View Post
Thanks - I didn't realize the overdrive had an "on/off" switch so to speak. Doesn't seem like a bad way to go - probably less fuss involved than the 700R4 swap we did in my K20.
Definitely a few different ways to go. The 700R4 may not be a bad deal as well.

Fortunately, I'm happy to say that this meets and exceeds my expectations and makes the Jimmy much more enjoyable to drive.

It is designed to operate while in 2 wheel drive. Doesn't seem to be a problem to me as I can't ever remember needing to go over 40 mph, or so while in 4 wheel drive.

The on/off switch works pretty darn good. Should I want, or need an additional gear, I just turn the unit on and utilize my pull switch.

Pat
Ptjsk is offline   Reply With Quote
Old 09-12-2020, 11:56 AM   #11
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,634
Re: Gear Vendors Overdrive

Drive shaft looks too short to me. How far does it go into the back of the GV
kwmech is offline   Reply With Quote
Old 09-12-2020, 12:30 PM   #12
jjzepplin
Registered User
 
jjzepplin's Avatar
 
Join Date: Feb 2012
Location: Ruskin Florida
Posts: 4,566
Re: Gear Vendors Overdrive

Interesting. I also cannot say enough about Tom Woods. Great company! When I installed my NP203 splitter and 1 ton axles they hooked me up. Pricey but absolutely no vibrations. They also suggested the Flat Furd flange for the NP205 and a bolt on the flange Cardan Joint (Spicer of course). Built in 2000 and still works great.
__________________
70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688 Yeller
72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 LS1-T56 3.73 LSD super budget build
Blanco-2014 Sierra SWB https://67-72chevytrucks.com/vboard/...d.php?t=810350
jjzepplin is offline   Reply With Quote
Old 09-13-2020, 09:58 AM   #13
Ptjsk
Registered User
 
Join Date: Jan 2018
Location: Northern CA
Posts: 588
Re: Gear Vendors Overdrive

Quote:
Originally Posted by kwmech View Post
Drive shaft looks too short to me. How far does it go into the back of the GV
The shaft of the gear vendor sticks out of the housing approximately 1" which is obviously hidden by the yoke.

The inside of the housing bottoms out at 3". So the end of the yoke is held back about an inch so there's plenty of room for "sliding" movement with suspension activation.

Pat

Last edited by Ptjsk; 09-13-2020 at 10:03 AM.
Ptjsk is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:05 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com