The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-26-2021, 09:04 PM   #1
Already Gone
70+ ( Old Skool Club )
 
Already Gone's Avatar
 
Join Date: Nov 2003
Location: Saskatoon, Saskatchewan ,Canada
Posts: 9,143
Are these the right height

I ordered these 4 inch drop springs and although correct part number on them they just look too short for a 4 inch drop. They are 9 inches high. Can anyone tell me for sure if they are the right ones for a 4 inch drop. It amy be a whie before I install them so want to make sure they are correct while I can still return them if not correct.
Attached Images
  
__________________
1972 C10 Custom/Deluxe 613 Highlander 406/700R4
1999 White Tahoe LS 4x2 with Z56 Police Package
1992 K1500 GMC Suburban

Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601

" Circumsatances Do Not Change Responsibility "

" The Sky is not the Limit, Your Mind is." Marilyn Monroe ..


RIP Charlie Watts 1941 - 2021
Already Gone is offline   Reply With Quote
Old 03-03-2021, 06:56 PM   #2
67C10Step
Registered User
 
67C10Step's Avatar
 
Join Date: Jul 2019
Location: Beebe, AR
Posts: 2,475
Re: Are these the right height

Sorry for the long delay in response to this. Those are the exact springs I put in the back of my 67 for a 4" drop. Photo below. Mine will obviously drop a bit more when I put the bed on it but this appears about right with the 2.5" drop in front that hasn't totally settled out just yet.

I also purchased some shortened bump stops for the rear and there is just a hair over 3.5" of clearance between the stop and the axle housing.
Attached Images
 
__________________
1967 C10
1980 Jeep CJ5
2020 Toyota 4Runner
2024 Toyota Tundra
67C10Step is offline   Reply With Quote
Old 03-03-2021, 09:08 PM   #3
Already Gone
70+ ( Old Skool Club )
 
Already Gone's Avatar
 
Join Date: Nov 2003
Location: Saskatoon, Saskatchewan ,Canada
Posts: 9,143
Re: Are these the right height

Quote:
Originally Posted by 67C10Step View Post
Sorry for the long delay in response to this. Those are the exact springs I put in the back of my 67 for a 4" drop. Photo below. Mine will obviously drop a bit more when I put the bed on it but this appears about right with the 2.5" drop in front that hasn't totally settled out just yet.

I also purchased some shortened bump stops for the rear and there is just a hair over 3.5" of clearance between the stop and the axle housing.
Thanks for the info. For your front 2 1/2 inch drop are you just using the dropped spindle with stock spring or a 2 1/2 inch dropped spring. Also what size tire you running front and back.
__________________
1972 C10 Custom/Deluxe 613 Highlander 406/700R4
1999 White Tahoe LS 4x2 with Z56 Police Package
1992 K1500 GMC Suburban

Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601

" Circumsatances Do Not Change Responsibility "

" The Sky is not the Limit, Your Mind is." Marilyn Monroe ..


RIP Charlie Watts 1941 - 2021
Already Gone is offline   Reply With Quote
Old 03-03-2021, 09:39 PM   #4
67C10Step
Registered User
 
67C10Step's Avatar
 
Join Date: Jul 2019
Location: Beebe, AR
Posts: 2,475
Re: Are these the right height

Standard height spring in front with 2-1/2" drop spindle. I wanted to keep the steering geometry as close to stock as possible. I've not driven my truck yet and I expect the front to settle a bit more since the springs are new as well.

I am runnin 255/70-15 all the way around.
__________________
1967 C10
1980 Jeep CJ5
2020 Toyota 4Runner
2024 Toyota Tundra
67C10Step is offline   Reply With Quote
Old 03-03-2021, 11:48 PM   #5
Already Gone
70+ ( Old Skool Club )
 
Already Gone's Avatar
 
Join Date: Nov 2003
Location: Saskatoon, Saskatchewan ,Canada
Posts: 9,143
Re: Are these the right height

Quote:
Originally Posted by 67C10Step View Post
Standard height spring in front with 2-1/2" drop spindle. I wanted to keep the steering geometry as close to stock as possible. I've not driven my truck yet and I expect the front to settle a bit more since the springs are new as well.

I am runnin 255/70-15 all the way around.
Thanks again. 255/70 15's are 29.04 inches high. I plan to run 255/60 17 which are the same height as your 255/70 15's and use a 2 1/2 inch spindle like you are and I like what tire to fender clearance you have up front. I'd like to see your truck when you get the box installed.
__________________
1972 C10 Custom/Deluxe 613 Highlander 406/700R4
1999 White Tahoe LS 4x2 with Z56 Police Package
1992 K1500 GMC Suburban

Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601

" Circumsatances Do Not Change Responsibility "

" The Sky is not the Limit, Your Mind is." Marilyn Monroe ..


RIP Charlie Watts 1941 - 2021
Already Gone is offline   Reply With Quote
Old 03-04-2021, 09:06 AM   #6
67C10Step
Registered User
 
67C10Step's Avatar
 
Join Date: Jul 2019
Location: Beebe, AR
Posts: 2,475
Re: Are these the right height

Quote:
Originally Posted by Already Gone View Post
Thanks again. 255/70 15's are 29.04 inches high. I plan to run 255/60 17 which are the same height as your 255/70 15's and use a 2 1/2 inch spindle like you are and I like what tire to fender clearance you have up front. I'd like to see your truck when you get the box installed.
Will do, mine is going step side. I got the wood for the bed a week or so ago an am going to pull the trigger on the whole box from Mar K soon. I'm anticipating the rear to drop another 1/2" or so when the bed is on and the front to settle about the same when the suspension articulates a bit.
__________________
1967 C10
1980 Jeep CJ5
2020 Toyota 4Runner
2024 Toyota Tundra
67C10Step is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:40 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com