|
09-06-2022, 07:43 AM
|
#1 |
|
Registered User
Join Date: May 2021
Location: Center Barnstead NH
Posts: 34
|
Glovebox stop arm?
I am building a truck that had the original glove box door removed. The truck is an A/C cab, when i installed a glovebox the stop arm hits the A/C vent, and wont allow full motion of glovebox door. Are the stop arms different from A/C to non? i know the one i installed is from a non A/C truck.
__________________
1972 C10 SWB 383 M22 1972 K20 454 1970 K5 1985 M1008 1986 M1008 2020 2500HD Duramax |
|
|
|
09-06-2022, 08:05 AM
|
#2 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Glovebox stop arm?
No, they are all the same. Is it bent?
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
09-06-2022, 08:17 AM
|
#3 |
|
Roadtrip!
 
Join Date: Feb 2003
Location: Grand Rapids MN
Posts: 13,813
|
Re: Glovebox stop arm?
The 67 arm is a little different but should still function the same i believe.
__________________
67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto |
|
|
|
|
09-06-2022, 08:24 AM
|
#4 |
|
Senior Member
Join Date: Dec 1999
Location: TX
Posts: 1,631
|
Re: Glovebox stop arm?
I'm gonna chime in to say, mine hits too...haven't looked into it too much. I have factory style vents, that I cut into a non AC dash....figured it was something I did...I also have vintage air with the tubing size adapters on the back of the factory style vents...
|
|
|
|
|
09-06-2022, 10:26 AM
|
#5 |
|
Registered User
Join Date: May 2021
Location: Center Barnstead NH
Posts: 34
|
Re: Glovebox stop arm?
I have done a few of these trucks but this is the first one i have had with A/C.
I have a pile of glovebox doors with arms all from non A/C trucks they all look the same. ( not bent ) I did install the Vintage air kit with the adapters so not sure if that made a difference. the outlet on the a/c vent sweeps to the left, right into the path of the glovebox arm.
__________________
1972 C10 SWB 383 M22 1972 K20 454 1970 K5 1985 M1008 1986 M1008 2020 2500HD Duramax |
|
|
|
|
09-15-2022, 09:58 PM
|
#6 |
|
Registered User
Join Date: May 2018
Location: Prattville, AL
Posts: 611
|
Re: Glovebox stop arm?
I have a '67 AC cab with Vintage Air installed. If I remember correctly I nipped off some of the glove box arm. I also remember rotating the vent adapter around so that duct pointed away from the arm tab.
__________________
-------------------------------------------------------- 1967 C10 "Snowball" (Currently in a thousand pieces down from a bazillion) 1989 Toyota DLX pickup "The Hulk" |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
