lets play the number game....again - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Longhorn Man · 09-20-2004, 09:46 PM

Picked up my 350 yesterday, now it is time to tace the origins of it. Can y'all hook me up? I still have absolutly no luck with this crap. I remember some one told me to call some one up, but I can't remember whom to call, nor do I have a number.

On the pad up front on the passenger side... 1M0528 And directly under that one is 6VP
Then on the bellhousing, hecho en Mexico...I know what that means... then under that 10066036
I know it is a 4 bolt main, newer (painted black, passenger dipstick) casting, Pretty sure it is a 350...I don't think anything else came in 4 bolt in the later engines...or was there a 4 bolt 305?

The heads, are also hecho en Mexico...scalloped lower edge, so I know they are a light weight casting...the intake looks pretty friggen huge, and I was told it was 2.02...but they may well be 1.94's...my eyes haven't been calibrated lately.

The head number was hard to make out....969...968....or 369. I think the last one is correct, but I am not 100% sure.
Anyone have anything for me?

I'm going to put new rod/main bearings, hone it out, new rings a good cleaning....debating on a cam or not....trying to go low buck here, and it just isn't adding up to low buck. The bore has absolutly no ridge in it at all.

dubie · 09-20-2004, 09:50 PM

10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear
seal, "Hecho en Mexico

LUV2XCLR8 · 09-20-2004, 09:52 PM

SCROLL DOWN TO YOUR NUMBER.

http://www.mortec.com/castnum.htm

LUV2XCLR8 · 09-20-2004, 09:52 PM

Quote:

Originally Posted by dubie

10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear
seal, "Hecho en Mexico

DAMN, BEAT ME BY LIKE 2 SECONDS.

Longhorn Man · 09-20-2004, 09:54 PM

did I list a date code there by chance...or is there not going to be one?

dubie · 09-20-2004, 09:55 PM

10054727...350...86-up...2 or 4...one piece rear seal, some "Made in Canada"
10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear
seal, "Hecho en Mexico"
10066038...350.....92....4...Goodwrench crate motor, 2-piece rear
seal, "Hecho en Mexico"

If it follows sequence, looks to be an 86 and up

Longhorn Man · 09-20-2004, 10:03 PM

Sweet...you guys rock.
i had forgotten that link...mortec is easier to use than nasty z28...but without the list of andy's favorites, I am lost.
How about the heads, any luck with them? Are they decent, best of the worst, worst of the worst?

dubie · 09-20-2004, 10:09 PM

got a head casting # for us?

Longhorn Man · 09-20-2004, 10:12 PM

The heads, are also hecho en Mexico...scalloped lower edge, so I know they are a light weight casting...the intake looks pretty friggen huge, and I was told it was 2.02...but they may well be 1.94's...my eyes haven't been calibrated lately. The head number was hard to make out....969...968....or 369. I think the last one is correct, but I am not 100% sure.

LUV2XCLR8 · 09-20-2004, 10:15 PM

http://www.auto-ware.com/techref/castnum.htm

ONLY THING I FOUND, SORRY.

dallas71 · 09-20-2004, 10:22 PM

This is what i found on the heads....
33417369...90-up...350..........Gen.I Goodwrench crate motor,"Hecho en Mexico", 76cc

Longhorn Man · 09-20-2004, 11:51 PM

76 cc...i like cheap gas...low compression heads will let me burn the cheap stuff.
Oh well...I'm just slappin it together to sell it.

Thanks again y'all.

09-20-2004, 09:46 PM	#1
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	lets play the number game....again Picked up my 350 yesterday, now it is time to tace the origins of it. Can y'all hook me up? I still have absolutly no luck with this crap. I remember some one told me to call some one up, but I can't remember whom to call, nor do I have a number. On the pad up front on the passenger side... 1M0528 And directly under that one is 6VP Then on the bellhousing, hecho en Mexico...I know what that means... then under that 10066036 I know it is a 4 bolt main, newer (painted black, passenger dipstick) casting, Pretty sure it is a 350...I don't think anything else came in 4 bolt in the later engines...or was there a 4 bolt 305? The heads, are also hecho en Mexico...scalloped lower edge, so I know they are a light weight casting...the intake looks pretty friggen huge, and I was told it was 2.02...but they may well be 1.94's...my eyes haven't been calibrated lately. The head number was hard to make out....969...968....or 369. I think the last one is correct, but I am not 100% sure. Anyone have anything for me? I'm going to put new rod/main bearings, hone it out, new rings a good cleaning....debating on a cam or not....trying to go low buck here, and it just isn't adding up to low buck. The bore has absolutly no ridge in it at all. Last edited by Longhorn Man; 10-19-2004 at 09:32 PM.

09-20-2004, 09:50 PM	#2
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,853	10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

09-20-2004, 09:52 PM	#3
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	SCROLL DOWN TO YOUR NUMBER. http://www.mortec.com/castnum.htm __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

09-20-2004, 09:55 PM	#6
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,853	10054727...350...86-up...2 or 4...one piece rear seal, some "Made in Canada" 10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico" 10066038...350.....92....4...Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico" If it follows sequence, looks to be an 86 and up __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

09-20-2004, 10:09 PM	#8
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,853	got a head casting # for us? __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

09-20-2004, 09:54 PM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	did I list a date code there by chance...or is there not going to be one?

09-20-2004, 10:03 PM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Sweet...you guys rock. i had forgotten that link...mortec is easier to use than nasty z28...but without the list of andy's favorites, I am lost. How about the heads, any luck with them? Are they decent, best of the worst, worst of the worst?

09-20-2004, 10:12 PM	#9
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	The heads, are also hecho en Mexico...scalloped lower edge, so I know they are a light weight casting...the intake looks pretty friggen huge, and I was told it was 2.02...but they may well be 1.94's...my eyes haven't been calibrated lately. The head number was hard to make out....969...968....or 369. I think the last one is correct, but I am not 100% sure.

09-20-2004, 10:15 PM	#10
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	http://www.auto-ware.com/techref/castnum.htm ONLY THING I FOUND, SORRY. __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

09-20-2004, 10:22 PM	#11
dallas71 Registered User Join Date: Mar 2004 Location: Corinth,TX Posts: 444	This is what i found on the heads.... 33417369...90-up...350..........Gen.I Goodwrench crate motor,"Hecho en Mexico", 76cc __________________ My 1966 LWB Truck My 1966 SWB Truck

09-20-2004, 11:51 PM	#12
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	76 cc...i like cheap gas...low compression heads will let me burn the cheap stuff. Oh well...I'm just slappin it together to sell it. Thanks again y'all.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.