replacing door locks??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ocbaud · 11-13-2004, 02:29 PM

I need to replace the locks on my truck. the driver's side lock is dead. anything that will fit in the lock, even by a couple mm's will turn and unlock it.

i'm trying to beef up the security for college soon. the alarm is good, but the door luck still needs fixed.

how do i go about changing the locks out and where would i get replacement ones at?

rolson1039 · 11-13-2004, 06:56 PM

i have found that most auto part stores like pep boys have cylinders. its real easy all ya need is a large screwdriver and you can reach in there and pop out the C style clips that hold them to the door skin then ya have a little awl or small flathead screwdriver that seperates the clip that holds the lock rod to the end of the lock cylinder. in short the hardest part of the whole thing is taking off the door panel.
I used to have an extra set laying around but i lost em in the mess.
Also almost any GM car lock cylinder wwill fit you may just have to change off the linkage int he back which is also easy enough just taking off a clip

apstguy · 11-14-2004, 02:26 AM

Yeah they tend to do that... I have an alarm for that reason. When I get around to fixing all the lock cylinders (all of them including the ignition are screwed up somehow) I'll fix it. It is very simple. Pop the rusted c-clip off and pull out. Reverse to reinstall!

C&C Chevy · 11-14-2004, 01:11 PM

Hey ocbaud, I just did this a few weeks ago after someone tried to break-in my truck with a screwdriver. The other guys are right. The hardest part is getting the door panel off. Also, the c-clip will pop off so don't drop inside the door. Happened to me and I had to use a magnet to get it out. I got my lock cylinders at NAPA for $34 for a set.

cochran63 · 11-14-2004, 03:28 PM

I replaced the locks in my 85 about 3 months ago. IT was a pretty simple swap. I think I gave 16 for the set at O'reily's

hotrodhomi · 11-14-2004, 03:38 PM

The locks might help, but anybody that strong enough to pick up a rock can still get in. Insurance, Insurance, Insurance. Good luck with the lock change out though.
HRH

rolson1039 · 11-14-2004, 03:59 PM

to prevent someone using the screwdriver trick you can rivet these pieces they make to your door skin which covers over the lock cylinder, but yet ive seen people pry those out to do the screwdriver trick... the thing is if they really want the truck they will get it.

11-13-2004, 02:29 PM	#1
ocbaud Garage Queen Material Join Date: Oct 2002 Location: USA Posts: 4,129	replacing door locks??? I need to replace the locks on my truck. the driver's side lock is dead. anything that will fit in the lock, even by a couple mm's will turn and unlock it. i'm trying to beef up the security for college soon. the alarm is good, but the door luck still needs fixed. how do i go about changing the locks out and where would i get replacement ones at?

11-13-2004, 06:56 PM	#2
rolson1039 Registered User Join Date: Oct 2002 Location: NJ Posts: 404	i have found that most auto part stores like pep boys have cylinders. its real easy all ya need is a large screwdriver and you can reach in there and pop out the C style clips that hold them to the door skin then ya have a little awl or small flathead screwdriver that seperates the clip that holds the lock rod to the end of the lock cylinder. in short the hardest part of the whole thing is taking off the door panel. I used to have an extra set laying around but i lost em in the mess. Also almost any GM car lock cylinder wwill fit you may just have to change off the linkage int he back which is also easy enough just taking off a clip __________________ so many trucks so little time!!!

11-14-2004, 02:26 AM	#3
apstguy LED King Join Date: Jan 2003 Location: Sacramento, CA Posts: 2,087	Yeah they tend to do that... I have an alarm for that reason. When I get around to fixing all the lock cylinders (all of them including the ignition are screwed up somehow) I'll fix it. It is very simple. Pop the rusted c-clip off and pull out. Reverse to reinstall! __________________ Tyler 1985 C10 305 w/ Bowtie OD TH700R4 3.42 LSD 202,000 miles 2006 Ford Focus ZX3 5-speed Stick 2016 Chevy Spark EV Gone: 2002.5 VW GTI 24v VR6 Gone: 2008 VW R32

11-14-2004, 01:11 PM	#4
C&C Chevy Registered User Join Date: Feb 2003 Location: Midwest City, OK Posts: 1,001	Hey ocbaud, I just did this a few weeks ago after someone tried to break-in my truck with a screwdriver. The other guys are right. The hardest part is getting the door panel off. Also, the c-clip will pop off so don't drop inside the door. Happened to me and I had to use a magnet to get it out. I got my lock cylinders at NAPA for $34 for a set. __________________ Robert Current: 1986 SWB Silverado 4.3 / TH400 Past: 1985 SWB Silverado 305 / TH350 - sold 1995 1987 1/2 ton Silverado - FI 350 / 700R4 sold 2007

11-14-2004, 03:28 PM	#5
cochran63 Registered User Join Date: Jan 2004 Location: Oklahoma Posts: 1,057	I replaced the locks in my 85 about 3 months ago. IT was a pretty simple swap. I think I gave 16 for the set at O'reily's __________________ Youth soon passes away, but immaturity can last a life time.

11-14-2004, 03:38 PM	#6
hotrodhomi Registered User Join Date: Apr 2004 Location: Sacramento Posts: 3,737	The locks might help, but anybody that strong enough to pick up a rock can still get in. Insurance, Insurance, Insurance. Good luck with the lock change out though. HRH

11-14-2004, 03:59 PM	#7
rolson1039 Registered User Join Date: Oct 2002 Location: NJ Posts: 404	to prevent someone using the screwdriver trick you can rivet these pieces they make to your door skin which covers over the lock cylinder, but yet ive seen people pry those out to do the screwdriver trick... the thing is if they really want the truck they will get it. __________________ so many trucks so little time!!!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.