Driveshaft Lengths - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Brainchild · 03-31-2005, 10:21 PM

I thought I posted this once,but couldn't find it,so here goes.

I am switching to an automatic in a few weeks.Now will the driveshaft from my 4 speed work with a short shaft 350 turbo if I put the yoke on it?

Also I have a longshaft 350,is this better than the shorty?I am going to have one rebuilt,and I have a long and short tranny.Is it worth having a shaft made to use the long shaft?

Longhorn Man · 03-31-2005, 10:44 PM

IF your current shaft won't fit with either TH350, and you have a short and a long in comparable condition, I would opt for the long shaft myself.
While it isn't correct, it'll be easier to get a replacement tranny later since short shafts are getting harder and harder to get, plus, a few inches makes a huge differance when tryin to do a one piece shaft.

J Y Dog · 03-31-2005, 11:33 PM

I'd go with the long tailshaft because thats what they had . Drive shafts should be
as common as dirt and about as cheap. Just advertise here for one and see what comes up.

J Y

Longhorn Man · 04-01-2005, 12:23 AM

JYdog...all the 67 - 72 trucks originally had short shaft trannys.

Brainchild · 04-01-2005, 01:45 AM

So if I go with the shorty,the driveline from my 4 gear will be the same length once I put a yoke on it?

J Y Dog · 04-01-2005, 06:22 AM

You're right L M I promise not to post under the hinfluence again.

Jim

Longhorn Man · 04-01-2005, 06:42 AM

Been there, done that.

03-31-2005, 10:21 PM	#1
Brainchild Still drivin' a Rat Rod Join Date: Sep 2004 Location: Monett Missouri Posts: 4,925	Driveshaft Lengths I thought I posted this once,but couldn't find it,so here goes. I am switching to an automatic in a few weeks.Now will the driveshaft from my 4 speed work with a short shaft 350 turbo if I put the yoke on it? Also I have a longshaft 350,is this better than the shorty?I am going to have one rebuilt,and I have a long and short tranny.Is it worth having a shaft made to use the long shaft? __________________ Rusty Member #13872 Instead of saying.....you are a discomfort in the back of my front.....one should be able to say...... you are a pain in the a$# 71 GMC LWB 49 Chevy 85 Chevy G20 Check out my website

04-01-2005, 01:45 AM	#5
Brainchild Still drivin' a Rat Rod Join Date: Sep 2004 Location: Monett Missouri Posts: 4,925	So if I go with the shorty,the driveline from my 4 gear will be the same length once I put a yoke on it? __________________ Rusty Member #13872 Instead of saying.....you are a discomfort in the back of my front.....one should be able to say...... you are a pain in the a$# 71 GMC LWB 49 Chevy 85 Chevy G20 Check out my website

03-31-2005, 10:44 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	IF your current shaft won't fit with either TH350, and you have a short and a long in comparable condition, I would opt for the long shaft myself. While it isn't correct, it'll be easier to get a replacement tranny later since short shafts are getting harder and harder to get, plus, a few inches makes a huge differance when tryin to do a one piece shaft.

03-31-2005, 11:33 PM	#3
J Y Dog Registered User Join Date: Jun 2002 Location: asheville, NC Posts: 63	I'd go with the long tailshaft because thats what they had . Drive shafts should be as common as dirt and about as cheap. Just advertise here for one and see what comes up. J Y

04-01-2005, 12:23 AM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	JYdog...all the 67 - 72 trucks originally had short shaft trannys.

04-01-2005, 06:22 AM	#6
J Y Dog Registered User Join Date: Jun 2002 Location: asheville, NC Posts: 63	You're right L M I promise not to post under the hinfluence again. Jim

04-01-2005, 06:42 AM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Been there, done that.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.