The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-30-2006, 01:46 AM   #1
MisterMan
Account Suspended
 
MisterMan's Avatar
 
Join Date: Jan 2006
Location: Visalia, California
Posts: 286
Thumbs down I have small problem

I have a 71' 2wd lwb gmc serria (v8 350)

I have leaf in the rear yet i wanna drop the truck on maybe 20 in rims or so. ne one know of a way to lower the rear besides flip the leaf from top of axle to bottom???

thanks tons!!!

---den
MisterMan is offline   Reply With Quote
Old 08-30-2006, 10:59 AM   #2
RSRXION
Senior Member
 
RSRXION's Avatar
 
Join Date: Jun 2006
Location: Arkansas
Posts: 227
Re: I have small problem

Easy enough . Use lowering blocks of the appropriate desired drop. JMHO, Dean
__________________
"They that give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety." Ben Franklin
RSRXION is offline   Reply With Quote
Old 08-30-2006, 11:43 AM   #3
Shane
Account Suspended
 
Shane's Avatar
 
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
Re: I have small problem

the leaf should already be on the bottom of the axle ... use blocks like rsrxion said ... cheap ... easy ... fast.
Shane is offline   Reply With Quote
Old 08-30-2006, 11:44 AM   #4
Alvin
Never Done?
 
Alvin's Avatar
 
Join Date: May 2000
Location: Ohio
Posts: 1,435
Re: I have small problem

Lowering blocks won't work without using the flip-kit. You really can't do much without using a flip kit. My GMC came with a leaf spring frame. Since I had decided to bag it, I bought a coil frame and swapped everything over.
__________________
Ethel - The Legend Continues...

Ethel has been sold.

Last edited by Alvin; 08-30-2006 at 11:56 AM.
Alvin is offline   Reply With Quote
Old 08-30-2006, 12:48 PM   #5
Shane
Account Suspended
 
Shane's Avatar
 
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
Re: I have small problem

I thought the leafs were mounted under the axle tubes on these rear ends?

I'm more familiar with coil rears ... that why I ask.
Shane is offline   Reply With Quote
Old 08-30-2006, 12:54 PM   #6
jkaylor68gmc
Senior Member
 
jkaylor68gmc's Avatar
 
Join Date: Dec 2005
Location: TN
Posts: 2,448
Re: I have small problem

Here is what I did, I have a GMC with leafs. First all, i flipped the rear end, it only lowers it about 4 3/4 inches. The front will sit perfect with a set of drop spindles and drop spring 2.5 inch drop springs that is. The rear crossmember directly behind the cab may need to be notched. Mine did because I also pulled a leaf. I could still put 20s on it with no problem. They look pimp down like this.
jkaylor68gmc is offline   Reply With Quote
Old 08-30-2006, 11:19 PM   #7
KAILUAZ
King of Rust
 
KAILUAZ's Avatar
 
Join Date: Jul 2005
Location: St Petersburg, FL
Posts: 359
Re: I have small problem

Quote:
Originally Posted by jkaylor68gmc View Post
Here is what I did, I have a GMC with leafs. First all, i flipped the rear end, it only lowers it about 4 3/4 inches. The front will sit perfect with a set of drop spindles and drop spring 2.5 inch drop springs that is. The rear crossmember directly behind the cab may need to be notched. Mine did because I also pulled a leaf. I could still put 20s on it with no problem. They look pimp down like this.

Which flip kit did you use? I have leafs also and need a drop, thanks.
__________________
1970 GMC 2500, 350, TH400, front disks, thats it!
My Pics
KAILUAZ is offline   Reply With Quote
Old 08-30-2006, 06:42 PM   #8
MisterMan
Account Suspended
 
MisterMan's Avatar
 
Join Date: Jan 2006
Location: Visalia, California
Posts: 286
Re: I have small problem

nope!! my leaf's are above the axle. it does have the stiffer *tow* package on it via glove box.

jkaylor68gmc: have ne pics???

THANKS ALOT TO EVERYONE!!!
MisterMan is offline   Reply With Quote
Old 08-30-2006, 09:38 PM   #9
67Fleet
Outlandish Trends - FL
 
67Fleet's Avatar
 
Join Date: Jul 2005
Location: Orlando
Posts: 1,396
Re: I have small problem

Leafs above the axle + blocks = lift, not lower. You need a flip kit.
__________________
-Bret
67 short-fleet sold!
67Fleet is offline   Reply With Quote
Old 08-31-2006, 12:46 AM   #10
MisterMan
Account Suspended
 
MisterMan's Avatar
 
Join Date: Jan 2006
Location: Visalia, California
Posts: 286
Re: I have small problem

Quote:
Originally Posted by 67Fleet View Post
Leafs above the axle + blocks = lift, not lower. You need a flip kit.
haha, i know, yet where to get a flip kit???
MisterMan is offline   Reply With Quote
Old 08-31-2006, 04:38 AM   #11
camaro__thunder
Epoxy Primer Friendly
 
camaro__thunder's Avatar
 
Join Date: Feb 2004
Location: South of Houston TEXXXAS
Posts: 680
Re: I have small problem

If you can weld go to Tractor Supply's trailer parts section and buy the 3" rearend perches and u-bolt setup for around $30.. Forget paying close to $100 for a simple U shaped piece of metal !
__________________
My Project 69 SWB
SHAVED BAGGED DOORED

Last edited by camaro__thunder; 08-31-2006 at 04:38 AM.
camaro__thunder is offline   Reply With Quote
Old 08-31-2006, 06:35 PM   #12
MisterMan
Account Suspended
 
MisterMan's Avatar
 
Join Date: Jan 2006
Location: Visalia, California
Posts: 286
Re: I have small problem

awesome. thanks!!
MisterMan is offline   Reply With Quote
Old 09-02-2006, 12:22 AM   #13
72MARIO
Registered User
 
72MARIO's Avatar
 
Join Date: Nov 2000
Location: Huntsville Ontario Canada
Posts: 4,051
Re: I have small problem

If your going 20's you may as well step notch and bag it to make the rims look at home on the truck.
__________________
1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair
http://67-72chevytrucks.com/vboard/s...d.php?t=625017
1967 C/20 6.0/4L80 Roofing Truck
1990 V2500 Suburban "Plow Truck"
2005 TAHOE DD
72MARIO is offline   Reply With Quote
Old 12-08-2006, 09:11 AM   #14
noahdallas
Registered User
 
noahdallas's Avatar
 
Join Date: Jul 2005
Location: Dallas, TX
Posts: 324
Re: I have small problem

I need some help please.... I have leaf springs but do not think they are factory. The brackets that hold the leaf springs are welding onto the frame. The leaf springs are under the axle. The rear end looks to be flipped because I cannot see the drain plug on the bottom. Is there a way to tell if I have a flip kit on it? The rear end and drive shaft line up at an angle, not straight. The truck sits really really low. I would be happy with a 2/4 drop. I see to put leaf springs plus blocks will raise it. But would the be my safe cause of my rear end and drive shaft being at an angle facing down? I will try to post some pice this weekend. Any help would be greatly appreciated.
noahdallas is offline   Reply With Quote
Old 12-09-2006, 03:03 PM   #15
XXL
Seņor Member
 
XXL's Avatar
 
Join Date: May 2002
Location: Edge of the world
Posts: 5,367
Re: I have small problem

Quote:
Originally Posted by noahdallas View Post
I need some help please.... I have leaf springs but do not think they are factory. The brackets that hold the leaf springs are welding onto the frame. The leaf springs are under the axle. The rear end looks to be flipped because I cannot see the drain plug on the bottom. .
Flip kit doesn't turn the rearend over... it 'flips' the relative position of the axle and spring (see pic below). Also, the plug on the rearend is not a drain plug, but rather a fill plug, and so it's supposed to be on top.
Attached Images
 
XXL is offline   Reply With Quote
Old 12-08-2006, 12:13 PM   #16
roj2323
Senior Member
 
Join Date: Mar 2004
Location: Somewhere
Posts: 985
Re: I have small problem

how about lowering springs and drop shackles. ECE sells them. you should be able to get about 3in of drop without doing a axle flip. ondrew
roj2323 is offline   Reply With Quote
Old 12-09-2006, 03:08 PM   #17
XXL
Seņor Member
 
XXL's Avatar
 
Join Date: May 2002
Location: Edge of the world
Posts: 5,367
Re: I have small problem

Quote:
Originally Posted by MisterMan View Post
...besides flip the leaf from top of axle to bottom???
Have the springs dearched. Any decent spring shop can do this kind of work. Basically, they take the spring pack apart, use proper heating techniques to change the arches of each leaf, then reassemble the packs. While doing this, they can also swap out or eliminate individual leafs to change the overall spring rate, and then can re-roll the eyes on the ends if needed (on a spring that had a big arch, when you dearch it significantly, the eye-to-eye distance gets too long, and so you end up with your shackles at a steep angle, which is not what you want).

It's been 20 years since I had springs done, but IIRC, RAy's Fort Worth Champion Spring did them for about $120/pair, and turnaround was a day. If you decide you want extreme lowering, you'll want to combine this method with the flip... plan on a signficant frame notch to go with it.
XXL is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:04 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com