67 LWB going to the scrap yard in 30 days - The 1947 - Present Chevrolet & GMC Truck Message Board Network

IvelDesigns · 02-20-2007, 02:05 AM

So if you see something you need, post it here and i'll cut it out. the truck is being stored about 2 hours from me, and i don't plan to get back up there until Mar 10 at the earliest. my plan is to see if anyone wants parts now, make a list, then pull them all at once and ship them the following monday.

Most of the bed is in pretty good shape. There are a few dents and some rust, but i'm guessing someone will see something they need.

the dash is uncut, but i'd be willing to cut it.

It's a 6 lug setup with drums all the way around. Trailing arms and cross member are gone, and the P side fender is shot, but the trim is good. the axle is an open 12 bolt, had some metal in the oil. bed floor is shot. not even worth cut pieces from. The grill guard is posted in another thread as are some of the other parts.

Oh, and the hood is still there (not pictured) with all of the letters. no dents that i saw, and no holes. very slight surface rust in a couple spots. The O has one peg that is broke, but there is still enough there to keep it in place... just glue it or something. $40 for the hood, no shipping

The D side fender is ok. has one small rust hole near the door, and one dent in the lower cup. that dent would be covered by a factor bumper though. also, the D side inner fender is still in good shape. $40 for both the outer and inner D side fender. no shipping

Please no PM's!! Post what you want here.

At this point, if the piece is less than 2' x 2', i'm thinkin around $10 per part. Tell me what you want, and your zip, and i'll get you a quote w/ shipping ASAP.

I do take PayPal and Money Orders.

IvelDesigns · 02-20-2007, 02:07 AM

more pics

CrashEd · 02-20-2007, 02:19 AM

Is the tailgate any good.

IvelDesigns · 02-20-2007, 02:31 AM

nope, it's junk. handle is bent, gate is bent, and has holes in the bottom. at most, the lettering may be good, but probably not worth cutting out and shipping.

CrashEd · 02-20-2007, 02:36 AM

Ok thanks

brak · 02-20-2007, 03:12 AM

Where in Iowa is the truck...

I'd be interested in the steering column and possibly the rear end.

picking up should be no problem

kohler · 02-20-2007, 06:56 AM

how about the front light harness,shipped to 12401
thanks chris

IvelDesigns · 02-20-2007, 10:19 AM

Quote:

Originally Posted by kohler

how about the front light harness,shipped to 12401
thanks chris

junk. most of the wiring was rigged together, so i got a bit happy with the wire cutters when pulling things apart.

IvelDesigns · 02-20-2007, 10:20 AM

Quote:

Originally Posted by brak

Where in Iowa is the truck...

I'd be interested in the steering column and possibly the rear end.

picking up should be no problem

The truck is in Dike Iowa, about 10 miles west of cedar falls/waterloo. I'll PM you with contact info.

grant's72 · 02-20-2007, 07:34 PM

if the back of the box is good I mite take this part if you have a pic Of the back I would like to see it too

Bob Moore · 02-20-2007, 08:16 PM

3 very small items for a buddy.

1. The neutral safty switch if this truck was a powerglide

2. Again if powerglide, the PRNDL lens from the column.

3. The rubber stop(block) the gas pedal hits on the floor. Accessible from the engine side of the firewall.

One more as I think about it - again if powerglide - the kick-down linkage rod from the carb all the way down to the transmission. Maybe 3 pieces total? A rod from carb, a lever type setup on the bellhousing(?), and another rod to the transmission.

Shipped to zip 98407 Tacoma, WA

67arch · 02-20-2007, 09:25 PM

I'm interested in rearview mirror if not to fogged.
auto column, need auto trans crossmember.
also passenger roof section from back seam to front driprail. From pass. driprail 12" in. Let me know if possible. Thanks

kohler · 02-20-2007, 09:47 PM

thanks anyway

IvelDesigns · 02-20-2007, 10:31 PM

Quote:

Originally Posted by grant's72

if the back of the box is good I mite take this part if you have a pic Of the back I would like to see it too

i didn't look to close, but the P side corner might be good. it does have a lens in it, so the chances are pretty good that it's in good shape. when i go up, i'll cut it out if it is in good shape and PM you a pic.

$10 + S & H and i'll leave the light and lens in it.

** edit **

just realized you are in iowa. if you want, you can come get it if you are close to waterloo to save the shipping. might be worth the trip if you're looking for other parts. PM me with your location

IvelDesigns · 02-20-2007, 10:35 PM

it was a powerglide, but has a 350 in it now. I'm not sure if the lens is still the PRNDL one or not, but if it is, i'll pull it. it's probably not in great shape though. the linkage is all 350 linkage, so no luck there.

when i go up there next i'll pull the parts and PM you the pics.

Quote:

Originally Posted by Bob Moore

3 very small items for a buddy.

1. The neutral safty switch if this truck was a powerglide

2. Again if powerglide, the PRNDL lens from the column.

3. The rubber stop(block) the gas pedal hits on the floor. Accessible from the engine side of the firewall.

One more as I think about it - again if powerglide - the kick-down linkage rod from the carb all the way down to the transmission. Maybe 3 pieces total? A rod from carb, a lever type setup on the bellhousing(?), and another rod to the transmission.

Shipped to zip 98407 Tacoma, WA

IvelDesigns · 02-20-2007, 10:46 PM

Quote:

Originally Posted by 67arch

I'm interested in rearview mirror if not to fogged.
auto column, need auto trans crossmember.
also passenger roof section from back seam to front driprail. From pass. driprail 12" in. Let me know if possible. Thanks

brak is first in line on the column.

i'm waiting to see if i can sell the rear wall before cutting the roof. also, i think there is rust along the drip rail, but i will look the next time i'm up there.

when i pull the engine/tranny (that same weekend) i'll look to see if the tranny member is good or not. $10 + S & H for it

the mirror is good and clear and not cracked if i'm not mistaken. $5 + S & H for the mirror

Bob Moore · 02-21-2007, 12:31 AM

Sounds good. Thanks - Bob

**70STOVEBOLT** · 02-21-2007, 05:40 PM

How about the shift indicator pointer? I dont' need the lens or the chrome part, just the pointer itself. Nobody makes 'em aftermarket that I can find, only the 70-72 style. Thanks, stovebolt

67arch · 02-21-2007, 11:19 PM

Quote:

Originally Posted by IvelDesigns

brak is first in line on the column.

i'm waiting to see if i can sell the rear wall before cutting the roof. also, i think there is rust along the drip rail, but i will look the next time i'm up there.

when i pull the engine/tranny (that same weekend) i'll look to see if the tranny member is good or not. $10 + S & H for it

the mirror is good and clear and not cracked if i'm not mistaken. $5 + S & H for the mirror

Sounds good, I want the mirror and hopefully tranny member is good also. Let me know on roof.
Thanks

1BadSS · 02-21-2007, 11:23 PM

Levi, is the pointer for the shift indicator any good? I accidentally broke mine.

BCOWANWHEELS · 02-21-2007, 11:41 PM

i want the throttle pedel and the steel rod linkage. got it?
bob
kingsport, tn. 37664

IvelDesigns · 02-22-2007, 12:22 AM

1badSS/70STOVEBOLT

brak has claimed the column pending payment. if he doesn't take it, i'll check the pointer to see if it's good or not. if my memory is right, it's not.

IvelDesigns · 02-22-2007, 12:23 AM

$5 for the pedal. it's posted in another thread. not sure on the linkage. when i go up there next, i'll check for it and PM you.

Quote:

Originally Posted by BCOWANWHEELS

i want the throttle pedel and the steel rod linkage. got it?
bob
kingsport, tn. 37664

BarryB · 02-22-2007, 06:58 AM

I am interested in the door and fender trim. how much and shipping to 37617.

Snohog · 02-22-2007, 07:41 AM

Is the core support any good?

02-20-2007, 02:05 AM	#1
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	67 LWB going to the scrap yard in 30 days So if you see something you need, post it here and i'll cut it out. the truck is being stored about 2 hours from me, and i don't plan to get back up there until Mar 10 at the earliest. my plan is to see if anyone wants parts now, make a list, then pull them all at once and ship them the following monday. Most of the bed is in pretty good shape. There are a few dents and some rust, but i'm guessing someone will see something they need. the dash is uncut, but i'd be willing to cut it. It's a 6 lug setup with drums all the way around. Trailing arms and cross member are gone, and the P side fender is shot, but the trim is good. the axle is an open 12 bolt, had some metal in the oil. bed floor is shot. not even worth cut pieces from. The grill guard is posted in another thread as are some of the other parts. Oh, and the hood is still there (not pictured) with all of the letters. no dents that i saw, and no holes. very slight surface rust in a couple spots. The O has one peg that is broke, but there is still enough there to keep it in place... just glue it or something. $40 for the hood, no shipping The D side fender is ok. has one small rust hole near the door, and one dent in the lower cup. that dent would be covered by a factor bumper though. also, the D side inner fender is still in good shape. $40 for both the outer and inner D side fender. no shipping Please no PM's!! Post what you want here. At this point, if the piece is less than 2' x 2', i'm thinkin around $10 per part. Tell me what you want, and your zip, and i'll get you a quote w/ shipping ASAP. I do take PayPal and Money Orders. Attached Images __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007... Last edited by IvelDesigns; 02-20-2007 at 02:40 AM.

02-20-2007, 02:07 AM	#2
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: 67 LWB going to the scrap yard in 30 days more pics Attached Images __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

02-20-2007, 02:19 AM	#3
CrashEd 72 chevy Join Date: Jan 2007 Location: Central Il Posts: 725	Re: 67 LWB going to the scrap yard in 30 days Is the tailgate any good.

02-20-2007, 02:31 AM	#4
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: 67 LWB going to the scrap yard in 30 days nope, it's junk. handle is bent, gate is bent, and has holes in the bottom. at most, the lettering may be good, but probably not worth cutting out and shipping. __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

02-20-2007, 02:36 AM	#5
CrashEd 72 chevy Join Date: Jan 2007 Location: Central Il Posts: 725	Re: 67 LWB going to the scrap yard in 30 days Ok thanks

02-20-2007, 03:12 AM	#6
brak Registered User Join Date: Apr 2006 Location: MinneSNOWta Posts: 1,381	Re: 67 LWB going to the scrap yard in 30 days Where in Iowa is the truck... I'd be interested in the steering column and possibly the rear end. picking up should be no problem __________________ 2003 GMC Sierra 1500 WT 1995 Nissan Hardbody 2016 Hyundai Veloster Turbo DC2 (SW/AW) Clyde W. Harvey USN "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery" Winston Churchill

02-20-2007, 06:56 AM	#7
kohler Registered User Join Date: Jan 2006 Location: new york,ulster Posts: 63	Re: 67 LWB going to the scrap yard in 30 days how about the front light harness,shipped to 12401 thanks chris

02-20-2007, 07:34 PM	#10
grant's72 Registered User Join Date: Sep 2006 Location: iowa Posts: 33	Re: 67 LWB going to the scrap yard in 30 days if the back of the box is good I mite take this part if you have a pic Of the back I would like to see it too Attached Images

02-20-2007, 08:16 PM	#11
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: 67 LWB going to the scrap yard in 30 days 3 very small items for a buddy. 1. The neutral safty switch if this truck was a powerglide 2. Again if powerglide, the PRNDL lens from the column. 3. The rubber stop(block) the gas pedal hits on the floor. Accessible from the engine side of the firewall. One more as I think about it - again if powerglide - the kick-down linkage rod from the carb all the way down to the transmission. Maybe 3 pieces total? A rod from carb, a lever type setup on the bellhousing(?), and another rod to the transmission. Shipped to zip 98407 Tacoma, WA __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

02-20-2007, 09:25 PM	#12
67arch WTB:Patience and Talent Join Date: Sep 2006 Location: Oklahoma Posts: 119	Re: 67 LWB going to the scrap yard in 30 days I'm interested in rearview mirror if not to fogged. auto column, need auto trans crossmember. also passenger roof section from back seam to front driprail. From pass. driprail 12" in. Let me know if possible. Thanks __________________ 69 shortwide

02-20-2007, 09:47 PM	#13
kohler Registered User Join Date: Jan 2006 Location: new york,ulster Posts: 63	Re: 67 LWB going to the scrap yard in 30 days thanks anyway

02-21-2007, 12:31 AM	#17
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: 67 LWB going to the scrap yard in 30 days Sounds good. Thanks - Bob __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

02-21-2007, 05:40 PM	#18
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,450	Re: 67 LWB going to the scrap yard in 30 days How about the shift indicator pointer? I dont' need the lens or the chrome part, just the pointer itself. Nobody makes 'em aftermarket that I can find, only the 70-72 style. Thanks, stovebolt __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

02-21-2007, 11:23 PM	#20
1BadSS NOT REALLY BANNED! Join Date: Jul 2004 Location: Shawnee, KS Posts: 1,072	Re: 67 LWB going to the scrap yard in 30 days Levi, is the pointer for the shift indicator any good? I accidentally broke mine. __________________ 1987 Mustang Coupe - 2.7 Stroker, 78mm turbo, Stainless header, 3" Exh, FMIC, 160lb/hr Injectors, MS3, twin walbro 255's, 34psi. Eating V8's daily. 04 Pontiac GTO 04 Ford Mustang GT 68 C20 LWB stripper truck 73 K5 Cheyenne 76 C20 Sierra Crew SRW 88 K20 Suburban I'm not hammering on metal just to hammer, i'm creating a piece of art.

02-21-2007, 11:41 PM	#21
BCOWANWHEELS Registered User Join Date: Nov 2006 Location: KINGSPORT,TN. Posts: 3,035	Re: 67 LWB going to the scrap yard in 30 days i want the throttle pedel and the steel rod linkage. got it? bob kingsport, tn. 37664 Last edited by BCOWANWHEELS; 02-21-2007 at 11:42 PM.



Register or Log In To remove these advertisements.

02-22-2007, 12:22 AM	#22
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: 67 LWB going to the scrap yard in 30 days 1badSS/70STOVEBOLT brak has claimed the column pending payment. if he doesn't take it, i'll check the pointer to see if it's good or not. if my memory is right, it's not. __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

02-22-2007, 06:58 AM	#24
BarryB Senior Member Join Date: Jul 2006 Location: Blountville, Tn. Posts: 3,904	Re: 67 LWB going to the scrap yard in 30 days I am interested in the door and fender trim. how much and shipping to 37617.

02-22-2007, 07:41 AM	#25
Snohog Junior Member Join Date: Dec 2001 Location: Indianapolis,IN Posts: 127	Re: 67 LWB going to the scrap yard in 30 days Is the core support any good? __________________ 68 SWB all over the garage 86 LWB silverado 2006 silverado SS

Register or Log In To remove these advertisements.