needs specs on Corvette c5 and c6 Upright - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Simonstrucker · 10-13-2007, 04:44 PM

I 'm working on doing a conversion with porterbuilt and need the specs on Corvette c5 and c6 Uprights.

abadsvt · 10-14-2007, 04:10 AM

What do you mean "uprights"? I am starting a c5 swap into my truck and might be able to answere some of your questions but i need a little more explanation.

Josh

Simonstrucker · 10-14-2007, 04:24 PM

I need the measurment of the stearing knuckle or Upright as it is somtimes called. I need the dementions from the top to bottom of ball joints and the camber and caster angles. Email Nate and he can give you more info of what he need thanks.

PBFAB.COM · 10-14-2007, 07:57 PM

Got it squared away... we were looking into the differences between the C5 and C6 Spindles. Turns out the differences are not in the dimensions of the pieces, just some small changes in brake caliper mounting location.

Simonstrucker · 10-14-2007, 08:09 PM

how is that project going

PBFAB.COM · 10-14-2007, 09:11 PM

Quote:

Originally Posted by Simonstrucker

how is that project going

FINALLY got it up on the table!

gringoloco · 10-14-2007, 11:35 PM

Hmmm... What are you brewin' up now?

PBFAB.COM · 10-15-2007, 09:56 AM

Quote:

Originally Posted by gringoloco

Hmmm... What are you brewin' up now?

Time will tell!

**N2TRUX** · 10-15-2007, 10:41 AM

Quote:

Originally Posted by porterbuilt

Time will tell!

Another one of these top secret frames? Hmmm? I think I need to set up a hidden camera in your shop...

SCOTI · 10-15-2007, 12:31 PM

Quote:

Originally Posted by porterbuilt

Time will tell!

Hhmmm. . . .... C5/C6 Dropmember????????

n2billet · 10-15-2007, 01:18 PM

God knows his C4 stuff is crap!

Maybe he will have better luck with the C5 stuff.....

SCOTI · 10-15-2007, 01:57 PM

Quote:

Originally Posted by n2billet

God knows his C4 stuff is crap!

I'd take one if I could (you know.... the budget being what it is

).
C5/6 would be even better . . ...

PBFAB.COM · 10-15-2007, 11:29 PM

This current "project" that has been mentioned is for a 55 Bel-Air Vert. it's getting all the C5 goodies on a custom chassis... the nice thing is that while I am in there setting up the C5 suspension I can get a lot of the "hard work" done for the next truck venture(s).

**N2TRUX** · 10-16-2007, 08:54 AM

Quote:

Originally Posted by porterbuilt

...I can get a lot of the "hard work" done for the next truck venture(s).

And I will assume he pays for R&D and we reap the benefits. I like that. I like that a lot...

jkade · 10-16-2007, 10:44 AM

Quote:

Originally Posted by porterbuilt

Got it squared away... we were looking into the differences between the C5 and C6 Spindles. Turns out the differences are not in the dimensions of the pieces, just some small changes in brake caliper mounting location.

So will a c5 spindle work on c4 arms???

PBFAB.COM · 10-16-2007, 03:57 PM

Quote:

Originally Posted by jkade

So will a c5 spindle work on c4 arms???

There will be a DropmemberC5 in the not too distant future... sometimes my version of time is skewed a bit, so don't expect it too soon!

It will use all C5 components... control arms, spindles and brakes... not too sure on the rack and pinion yet.

As for C5 spindles working on C4 arms... no.

jkade · 10-17-2007, 10:28 AM

Quote:

Originally Posted by porterbuilt

There will be a DropmemberC5 in the not too distant future... sometimes my version of time is skewed a bit, so don't expect it too soon!

It will use all C5 components... control arms, spindles and brakes... not too sure on the rack and pinion yet.

As for C5 spindles working on C4 arms... no.

I didn't think they would. I have been looking around for vette front suspension and the c5 stuff seems to be triple the price of c4. I think I am going to stick with c4.

SCOTI · 10-17-2007, 11:58 AM

Quote:

Originally Posted by jkade

I didn't think they would. I have been looking around for vette front suspension and the c5 stuff seems to be triple the price of c4. I think I am going to stick with c4.

I remember reading lately on one of the g-machine forums that the C5/6 stuff wasn't priced too high?? They were listing dealer pricing on arms/spindles & from what I remember it wasn't extreme (< $150 --> 200 for each arm new). That's similar pricing to a set of ART (or similar) arms but used C4 stuff can be found cheaper.

The big question would be: For our application (a C10 truck) how much more substantial would the geometry gains be for C5/6 vs. C4? The C5/6 stuff is so effective on a Y-body because of the perimeter frame that surrounds it & the ideal 50/50 weight bias. That's unlikely in a C10 w/o some serious effort & customizing.

Would the gains be worth the added exspense if there's any gains @ all?

jkade · 10-17-2007, 01:45 PM

Quote:

Originally Posted by SCOTI

I remember reading lately on one of the g-machine forums that the C5/6 stuff wasn't priced too high?? They were listing dealer pricing on arms/spindles & from what I remember it wasn't extreme (< $150 --> 200 for each arm new). That's similar pricing to a set of ART (or similar) arms but used C4 stuff can be found cheaper.

The big question would be: For our application (a C10 truck) how much more substantial would the geometry gains be for C5/6 vs. C4? The C5/6 stuff is so effective on a Y-body because of the perimeter frame that surrounds it & the ideal 50/50 weight bias. That's unlikely in a C10 w/o some serious effort & customizing.

Would the gains be worth the added exspense if there's any gains @ all?

I haven't checked new pieces but the used stuff seems to be pretty high. A lot of people don't think of gm selling parts cheap but like you say sometimes you can buy new parts from gm cheaper than you can buy used else where. Good point

ulakovic22 · 05-21-2012, 07:37 AM

Has there been any progress on a C5/6 dropmember or is the C4 still the only option?
Posted via Mobile Device

PBFAB.COM · 05-21-2012, 01:15 PM

Quote:

Originally Posted by ulakovic22

Has there been any progress on a C5/6 dropmember or is the C4 still the only option?
Posted via Mobile Device

There will be a C5 C6 option in the near future.

Nate

gringoloco · 05-21-2012, 02:05 PM

Quote:

Originally Posted by porterbuilt

There will be a C5 C6 option in the near future.

Nate

Cool! I still have my arms and spindles from before...

Coilovers, I assume? 'Vette rack or M2?
Posted via Mobile Device

ulakovic22 · 05-21-2012, 02:54 PM

Quote:

Originally Posted by porterbuilt

There will be a C5 C6 option in the near future.

Nate

Anything I can do? I shot you a PM about my plans for my current project and this DM would be a great starting point.

PBFAB.COM · 05-21-2012, 03:00 PM

Just get ahold of us here at the shop 480-297-2621 and talk to Dave. You can also e-mail him: porterbuiltdirect@gmail.com or send him a PM here on the forum "Porterbuilt Direct" is his username. He handles all the calls and e-mails then filters to my "to do" list all the items that I personally need to address. Helps me make sure we don't miss anybody.

Nate

PBFAB.COM · 05-21-2012, 03:01 PM

Quote:

Originally Posted by gringoloco

Cool! I still have my arms and spindles from before...

Coilovers, I assume? 'Vette rack or M2?
Posted via Mobile Device

79-93 Mustang rack.

Coil-over for sure.... most likely a Shockwave option as well.

Nate

10-13-2007, 04:44 PM	#1
Simonstrucker Big Block Short Bed Stepside Join Date: Sep 2005 Location: Port Saint Lucie Posts: 138	needs specs on Corvette c5 and c6 Upright I 'm working on doing a conversion with porterbuilt and need the specs on Corvette c5 and c6 Uprights. __________________ Big Block Club Short Bed Stepside Club Disk Brake Club Last edited by Simonstrucker; 10-13-2007 at 04:44 PM.

10-14-2007, 04:10 AM	#2
abadsvt Senior Member Join Date: Aug 2006 Location: Atascadero, CA Posts: 1,152	Re: needs specs on Corvette c5 and c6 Upright What do you mean "uprights"? I am starting a c5 swap into my truck and might be able to answere some of your questions but i need a little more explanation. Josh __________________ (Project truck) 1970 C10 under complete transformation My current build thread http://67-72chevytrucks.com/vboard/s...d.php?t=212871 Other project: C5 corvette swap into 70 c10 http://67-72chevytrucks.com/vboard/s...=1#post2413517 On Hold

10-14-2007, 04:24 PM	#3
Simonstrucker Big Block Short Bed Stepside Join Date: Sep 2005 Location: Port Saint Lucie Posts: 138	Re: needs specs on Corvette c5 and c6 Upright I need the measurment of the stearing knuckle or Upright as it is somtimes called. I need the dementions from the top to bottom of ball joints and the camber and caster angles. Email Nate and he can give you more info of what he need thanks. __________________ Big Block Club Short Bed Stepside Club Disk Brake Club

10-14-2007, 07:57 PM	#4
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: needs specs on Corvette c5 and c6 Upright Got it squared away... we were looking into the differences between the C5 and C6 Spindles. Turns out the differences are not in the dimensions of the pieces, just some small changes in brake caliper mounting location. __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!

10-14-2007, 08:09 PM	#5
Simonstrucker Big Block Short Bed Stepside Join Date: Sep 2005 Location: Port Saint Lucie Posts: 138	Re: needs specs on Corvette c5 and c6 Upright how is that project going __________________ Big Block Club Short Bed Stepside Club Disk Brake Club

10-14-2007, 11:35 PM	#7
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: needs specs on Corvette c5 and c6 Upright Hmmm... What are you brewin' up now? __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

10-15-2007, 01:18 PM	#11
n2billet Village Idiot.... Join Date: Jul 2003 Location: Rowlett, Texas Posts: 1,833	Re: needs specs on Corvette c5 and c6 Upright God knows his C4 stuff is crap! Maybe he will have better luck with the C5 stuff.....

10-15-2007, 11:29 PM	#13
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: needs specs on Corvette c5 and c6 Upright This current "project" that has been mentioned is for a 55 Bel-Air Vert. it's getting all the C5 goodies on a custom chassis... the nice thing is that while I am in there setting up the C5 suspension I can get a lot of the "hard work" done for the next truck venture(s). __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!

05-21-2012, 07:37 AM	#20
ulakovic22 Registered User Join Date: Aug 2008 Location: Lantana, TX Posts: 419	Re: needs specs on Corvette c5 and c6 Upright Has there been any progress on a C5/6 dropmember or is the C4 still the only option? Posted via Mobile Device

05-21-2012, 03:00 PM	#24
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: needs specs on Corvette c5 and c6 Upright Just get ahold of us here at the shop 480-297-2621 and talk to Dave. You can also e-mail him: porterbuiltdirect@gmail.com or send him a PM here on the forum "Porterbuilt Direct" is his username. He handles all the calls and e-mails then filters to my "to do" list all the items that I personally need to address. Helps me make sure we don't miss anybody. Nate __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.