Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
01-06-2008, 03:44 PM | #1 |
Registered User
Join Date: Nov 2007
Location: Temple, Texas
Posts: 75
|
Suggestion on repair of frame
Here is a pic of my left front upper shock mount hole. As you can see in the pics it has been worn pretty bad. What suggestions or ideas are there to repair this area. The one idea I have heard was to take a washer of same thickness of the frame with the right diameter whole and weld it in the worn out area of the frame. This make take some work to grind down the washer to fit the frame or grind the frame down some to get the washer to fit. Hope I made sense. Looking for some suggestions. Thanks in advance.
Mike
__________________
1964 GMC SWBFS 2005 Dodge Magnum RT Last edited by mtburg71; 01-06-2008 at 03:44 PM. |
01-06-2008, 03:52 PM | #2 |
Lowered in Cleveland
Join Date: Feb 2006
Location: Cleveland
Posts: 120
|
Re: Suggestion on repair of frame
I would repair the entire section of the frame, by cutting out a piece from the top lip to the bottom. Make a hole where the original shock mount was located and weld it in. It is a really easy fix. Good luck
|
01-06-2008, 04:57 PM | #3 |
Registered User
Join Date: Feb 2007
Location: South West Pennsylvania
Posts: 164
|
Re: Suggestion on repair of frame
Sir, you could just weld up the hole and install the aftermarket shock mounts that are much stronger. I have attached a link:
http://www.performanceonline.com/sto...cat=778&page=1
__________________
RED RUMBLE 1963 C10 Chevy Truck Owned since 1984 |
01-06-2008, 07:05 PM | #4 | |
Registered User
Join Date: Nov 2007
Location: Temple, Texas
Posts: 75
|
Re: Suggestion on repair of frame
Quote:
__________________
1964 GMC SWBFS 2005 Dodge Magnum RT |
|
01-06-2008, 07:44 PM | #5 |
Registered User
Join Date: Aug 2005
Location: Hillsboro Oregon
Posts: 6,449
|
Re: Suggestion on repair of frame
Use a holesaw that's just bigger than the affected area. Weld bridge across the existing hole so the guide bit has something to go through. Use the same holesaw to cut a blank out of 3/16" plate. Weld it in and drill your shock mount hole.
Just don't skimp on the quality of the holesaw. Be prepared to pay ~$20 for a decent one that will make it through those two cuts. And be sure to use plenty of cutting oil. Last edited by Frizzle Fry; 01-06-2008 at 07:45 PM. |
01-06-2008, 08:26 PM | #6 |
Registered User
Join Date: Sep 2006
Location: colorado springs colorado
Posts: 737
|
Re: Suggestion on repair of frame
I had the same issue onmy old 71. I found a large nut that would fit over the shock stud and ground the outside of the nut until it would fit in the hole. Welded it in and never had another problem with it.
I think i used a 5/8 or 3/4 nut. One of those should fit over the shock stud. Frank
__________________
70 chevy lwb c10 454/th400 and a 9" rearend suicide doors, marker light fuel fill, 4" cowl , mini tub |
01-07-2008, 02:11 AM | #7 |
Registered User
Join Date: Feb 2007
Location: South West Pennsylvania
Posts: 164
|
Re: Suggestion on repair of frame
Sir, the repair part is only $59.10. You receive a pair of these brackets. Welding up the frame is also a good fix. However if the truck is lowered, the aftermarket brackets correct the shock angle and prevent them from bottoming out.
__________________
RED RUMBLE 1963 C10 Chevy Truck Owned since 1984 |
01-08-2008, 10:57 AM | #8 |
Registered User
Join Date: Nov 2007
Location: Temple, Texas
Posts: 75
|
Re: Suggestion on repair of frame
Had to take a 2nd look at the link you sent. Thanks for pointing it out.
__________________
1964 GMC SWBFS 2005 Dodge Magnum RT |
01-09-2008, 05:11 PM | #9 |
Registered User
Join Date: Dec 2007
Location: Kimberley, BC, Canada
Posts: 799
|
Re: Suggestion on repair of frame
Mike, I like Frank's idea of the big nut welded into the hole. Just replacing the existing metal will fix the problem, but it isn't really much stronger than stock. A grade 5 or 8 nut will be pretty tough and have a lot more heft than the frame.
Good luck, Greg |
01-09-2008, 05:38 PM | #10 |
SIR
Join Date: Apr 2005
Location: grants pass oregon,usa
Posts: 658
|
Re: Suggestion on repair of frame
...idea, wuile shopping in my local hardware store I came across some 1"x1" square plates with small
holes pre cut in the center -1/2-5/8 I think they where made by "draw tite" ( not shure) I have used them to repair shock mounts and resize and beef up frame holes just weld them in place...price 80 cents....buy a BUNCH....
__________________
66long low fleet http://community.webshots.com/user/LVNR66 |
Bookmarks |
|
|