CST Emblem Placement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

stokers · 02-11-2008, 11:53 PM

Could someone please give me a measurement for the placement of the CST emblem located on the top edge of the doors. The measurment from the door edge closest to the door handle to the edge of the emblem should give me what I want. I just want to make sure before I start drilling holes.

Thanks,

Bob S.

**too much stuff** · 02-12-2008, 12:53 AM

It looks like 13 3/16" from the rear edge of the door to the edge of the emblem. Hope that makes sense.

DANTES JIMMY · 02-12-2008, 02:13 AM

Drilling Holes In Fresh Paint Or Sheetmetal Makes Me Sick
Ive Often Wondered If You Could Silicone Them On Or Trim Adhesive
Maybe Even Some Good 3m Double Stick Of Some Sort
I Had A Crappy Old Scout Once And Used Subfloor Adhesive(pl 400)
And Glued Some Mouldings Back On But I Didnt Care Much About The End Result And That Stuff Wasnt Coming Back Off Without A Pry Bar

stokers · 02-12-2008, 04:54 AM

Thanks, I'm sending it off to be painted next week so now is the time to put the holes in it. I kinda like the idea of using an adhesive. If anyone has done it this way please let me know.

johnboymx · 02-12-2008, 12:18 PM

hope this helps. The holes looked centered in the groove.

02-11-2008, 11:53 PM	#1
stokers Registered User Join Date: Aug 2007 Location: Lexington, KY Posts: 33	CST Emblem Placement Could someone please give me a measurement for the placement of the CST emblem located on the top edge of the doors. The measurment from the door edge closest to the door handle to the edge of the emblem should give me what I want. I just want to make sure before I start drilling holes. Thanks, Bob S.

02-12-2008, 12:53 AM	#2
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,787	Re: CST Emblem Placement It looks like 13 3/16" from the rear edge of the door to the edge of the emblem. Hope that makes sense. __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

02-12-2008, 02:13 AM	#3
DANTES JIMMY Registered User Join Date: Jan 2008 Location: PENDLETON,INDIANA Posts: 271	Re: CST Emblem Placement Drilling Holes In Fresh Paint Or Sheetmetal Makes Me Sick Ive Often Wondered If You Could Silicone Them On Or Trim Adhesive Maybe Even Some Good 3m Double Stick Of Some Sort I Had A Crappy Old Scout Once And Used Subfloor Adhesive(pl 400) And Glued Some Mouldings Back On But I Didnt Care Much About The End Result And That Stuff Wasnt Coming Back Off Without A Pry Bar

02-12-2008, 04:54 AM	#4
stokers Registered User Join Date: Aug 2007 Location: Lexington, KY Posts: 33	Re: CST Emblem Placement Thanks, I'm sending it off to be painted next week so now is the time to put the holes in it. I kinda like the idea of using an adhesive. If anyone has done it this way please let me know.

02-12-2008, 12:18 PM	#5
johnboymx johnboymx Join Date: Mar 2007 Location: washington Posts: 127	Re: CST Emblem Placement hope this helps. The holes looked centered in the groove. Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.