Lugs nuts to mount slots on my 2500?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BurnerBrown · 04-12-2008, 10:58 PM

I am trynig to figure out what lug nuts to use on my 68 2500 GMC to mount aluminum slots. What is the thread pattern on my truck? Not sure how to figure this out or where to buy em. I looked at Napa and Pepboys out of convienence and they didn't have enough lug nuts even if I could have figured out what lug to use.

airdale94 · 04-12-2008, 11:04 PM

They should be 1/2" fine but they might be 9/16" fine not sure what year they went to 9/16". You probably need the ones with the long shank. The one where part of the lugnut rides in the bolt hole. Unilug style. And you'll probably need some washers. You should be a able to buy a set with everything. Maybe Mr. Gasket. Basically what you want is the shank part as thick as the wheel.

Longhorn Man · 04-12-2008, 11:16 PM

1/2 inch... 9/16 came in 71 wih the disk brakes.

Arad68 · 04-13-2008, 07:07 AM

You can get them here. He is a great guy and has very fast shipping.

http://stores.ebay.com/TorqueThrust-...QQftidZ2QQtZkm

BurnerBrown · 04-13-2008, 11:08 PM

thanks. will post a pic when the slots are mounted up.

04-12-2008, 10:58 PM	#1
BurnerBrown Registered User Join Date: Jan 2005 Location: Landsale PA Posts: 82	Lugs nuts to mount slots on my 2500?? I am trynig to figure out what lug nuts to use on my 68 2500 GMC to mount aluminum slots. What is the thread pattern on my truck? Not sure how to figure this out or where to buy em. I looked at Napa and Pepboys out of convienence and they didn't have enough lug nuts even if I could have figured out what lug to use.

04-12-2008, 11:04 PM	#2
airdale94 Registered User Join Date: Jan 2007 Location: Topeka,KS Posts: 778	Re: Lugs nuts to mount slots on my 2500?? They should be 1/2" fine but they might be 9/16" fine not sure what year they went to 9/16". You probably need the ones with the long shank. The one where part of the lugnut rides in the bolt hole. Unilug style. And you'll probably need some washers. You should be a able to buy a set with everything. Maybe Mr. Gasket. Basically what you want is the shank part as thick as the wheel. Last edited by airdale94; 04-12-2008 at 11:07 PM. Reason: add

04-12-2008, 11:16 PM	#3
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Re: Lugs nuts to mount slots on my 2500?? 1/2 inch... 9/16 came in 71 wih the disk brakes.

04-13-2008, 07:07 AM	#4
Arad68 Trucks N Tranzams Join Date: Dec 2002 Location: North Las Vegas, Nevada Posts: 816	Re: Lugs nuts to mount slots on my 2500?? You can get them here. He is a great guy and has very fast shipping. http://stores.ebay.com/TorqueThrust-...QQftidZ2QQtZkm __________________ Don '68 Chevy LB 383 TH400/GV/373 posi '56 Chevy 4WD SWB '64 Chevy short stepside '79 Trans Am 455/TH2004R/12blt/4whldisc 95 Kia (Wifes car) 2002 S-10 extended cab pickup "God punishes small sins immediately"

04-13-2008, 11:08 PM	#5
BurnerBrown Registered User Join Date: Jan 2005 Location: Landsale PA Posts: 82	Re: Lugs nuts to mount slots on my 2500?? thanks. will post a pic when the slots are mounted up.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.