|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-20-2008, 07:53 PM
|
#1 |
|
high-Tech Red Neck
Join Date: Feb 2008
Location: Livingston, MT/On my boat WA/BC/AK
Posts: 2,294
|
Trying to ID a 3/4 ton front axle
Hey everyone, got this axle today, not sure what it is, It doesnt look quite like a Dana 44, the tubes are bigger, but it doesnt quite look like a dana 60. Anyone know what it is, it is out of a 77 Chevy 3/4 ton, the rear end is a 14B FF, and the T-case is a 203 mated to a TH350 4bbl original.
  Going to possibly stuff this axle under my 72 Blazer to make it an 8 lug. 
__________________
"He used to be a pretty nice feller, now he's a welder!" |
|
|
|
07-20-2008, 08:09 PM
|
#2 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Trying to ID a 3/4 ton front axle
10-bolt
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
07-20-2008, 08:12 PM
|
#3 |
|
high-Tech Red Neck
Join Date: Feb 2008
Location: Livingston, MT/On my boat WA/BC/AK
Posts: 2,294
|
Re: Trying to ID a 3/4 ton front axle
I am just figuring out, thats a total let down. Oh well, it will fetch a few bucks at the scrapper.
__________________
"He used to be a pretty nice feller, now he's a welder!" |
|
|
|
|
07-20-2008, 09:48 PM
|
#4 |
|
Registered User
Join Date: Feb 2007
Location: Carroll County Maryland ,
Posts: 828
|
Re: Trying to ID a 3/4 ton front axle
The 10 bolt is not a bad axle if you are just going for the 8 lug set up to run big tires on a street queen . I think O.R.D has a 10 bolt in one of there wheeling trucks .
__________________
1970 k/5 blazer--> money pit - 14bolt dana 44 350 sm465/205 36 14.50 16 tires 1972 nova plane jane 6 clyinder might sell might keep dont know 2004 chevy s-10 crewcab zr5 sold 1985 c20 chevy long bed , beater , on its way to a better place in pa from what the dmv told me 2010 kia forte koup 2.4 sx -over the river and threw the woods to the total lot it went . 1999 k1500 suburban 350 vortec 4l60e leather land yacht . |
|
|
|
|
07-20-2008, 09:56 PM
|
#5 | |
|
high-Tech Red Neck
Join Date: Feb 2008
Location: Livingston, MT/On my boat WA/BC/AK
Posts: 2,294
|
Re: Trying to ID a 3/4 ton front axle
Quote:
__________________
"He used to be a pretty nice feller, now he's a welder!" |
|
|
|
|
|
07-21-2008, 06:37 AM
|
#6 |
|
Registered User
Join Date: Dec 1999
Location: Old Mission, MI, USA
Posts: 2,507
|
Re: Trying to ID a 3/4 ton front axle
The spindles, hubs, rotors and brake backing plates will swap off that 10 bolt onto your Dana 44 to get 8 lug on your truck. No reason to swap the whole axle, and the calipers are the same so you don't even need to disconnect the brake hoses.
__________________
Tim |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
