New to this forum, old salt otherwise,... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

asphaltburner · 07-31-2008, 01:01 AM

Yo! Y'all!
Building a free (hauled from a cow pasture near Wyoming), nearly rust-free, '78 3/4 ton 4x4 P/U using my ol', rusty, beater, '73 3/4 ton 4x4 flatbed (from Missouri) as a donor.
Out went the full-time 4x4 corporate front axle/spring combo in exchange for the flatbed's front spring assembly and Dana 44 with Warn locking hubs. Out went the 4120 lb rated rear spring/axle assembly in exchange for the flatbed's 5560 lb rated rear assembly. New tall tires and the P/U sits proud! Refurbished, or junkyard replaced, all that I could, and bought new for anything I couldn't.
Built a 350 V8 that'll produce near 400 ftlbs of torque and about 325 hp, just like the one I run in my '76 Camaro that I built about 30,000 miles ago, and drive everyday to work.
Had the P/U's only really fine part, a TH400, rebuilt by AAMCO. Added a new 1200-1500 stall speed converter and had them imstall a long output shaft (2WD version,...the 4WD version is "rare as the dodo"), and bought a modified twin stick, rebuilt, NP205 transfercase from Off Road Design in Carbondale, CO. to solve the tough shifting of the NP205 and allow me independant control of the front and rear axles. Also purchased the "rare as a dodo" reproduced TH400/NP205 aluminum adapter from the same source. The "bulletproof" NP205 as modified will allow me to shift on-the-fly and give me rear wheel high/low, 4x4 high/low, and FRONT wheel drive high/low!
New grille, dashpad, floor covering (underlayment, 1/4" foil-backed wool, and full-floor vinyl,...after minor floor repairs), weatherstripping, and just finished re-upholstering the seat last Sunday in the near 100 degree heat,...damn hot, but sure made that vinyl contour nicely! Just finished electrical, and working on the fuel system now (aux tank was disconnected and is full of running rust! Donor flatbed's 20 gal tank will substitute nicely, and I pulled it tonight, I'll wash and dry it in the AM). A new six port valve will swap tanks and I'll add a small fuel gauge below the dash so I can monitor both tanks continuously.
Nearing driveline installation,...then I'll measure, select the best of my front and rear driveshafts, and have them altered to fit the installation.
Brand new steel hood awaits installation, as does a new rear chrome bumber to match the perfect front one.
Glad to be here and I hope to contribute as much as I can by passing on the knowledge and techniques that I've learned over thirty plus years of repairing, building, and painting all types of cars and trucks.
Todd, alias asphaltburner.

krue · 07-31-2008, 01:15 AM

Welcome to the board from South Mississippi!

Walts_restoration · 07-31-2008, 01:57 AM

hey man i think i know who you are :P

people are gonna say it after me, so

asphaltburner · 07-31-2008, 03:20 AM

Yo! walts-restoration!
Yeah, yeah, yeah! My driver's fender is off right now for door alignment, and it's just not pic time yet,...gimme a couple days to get it right, and re-installed. Kinda embarassing looking at the moment! Lots to come! Todd.

Cyclone44 · 07-31-2008, 06:44 AM

from Knoxville Tn...

jsbgump · 07-31-2008, 09:51 AM

Welcome to the board from Texas

shaneschevys · 07-31-2008, 10:34 AM

welcome from FT Worth TX.

BACKYARD88 · 07-31-2008, 10:43 AM

from South Texas!

asphaltburner · 07-31-2008, 10:55 AM

Yo! How 'bout this? Todd.

Walts_restoration · 07-31-2008, 12:24 PM

thats exzactly the truck im looking for man. an old 4x4 3/4 farm truck. Id hit it man.

BigDaddyDave · 07-31-2008, 01:12 PM

Welcome to the board from NC.

asphaltburner · 07-31-2008, 01:45 PM

Yo! walts_restoration!
Glad you like my choice! I just got lucky that it was nearly abandoned out there with the cows,...didn't even have a rear window! BUT N Colorado/Wyoming wind and dry saved it!
I expect that I'll have about $7000 into the whole project when I get to smoke all four wheels at once for the first time,...or maybe I'll put 'er in front wheel drive and scare some folks!
Anyway, the factory fuel tanks (one from from each truck) are drying in my driveway right now, having found the cheap, aftermarket aux. tank full of running rust! Into the flatbed it went this AM to haul to the junkyard with all the other leftover crap,...it'll bring $100/ton when I'm done! That'll pay for the cost of flatbedding this '78 P/U to my house from the cow pasture! Sorry, I thought I had pics on nastz28.com but they could be on previous pages in my thread that you've not seen! More to come, and I will probably retire this thread, and head to the more appropriate forum soon,...isn't it 73-8?(something,...but oddly not '80) trucks forum? Todd.

asphaltburner · 07-31-2008, 01:52 PM

And thanks to all for the kind welcome!! I'll try to take the time to help some of these members, if they'll let me. I've built alot of vehicles, and maintain eleven collected ones at the moment. Here's one of my favorites:

72BlckButy · 07-31-2008, 02:00 PM

to the board from Mid-MO!!!

Walts_restoration · 07-31-2008, 03:08 PM

Love the old deere. My old mans got a 1938 John deere A on the farm, never been left outside or in the rain a day of its life, all near completely original, and about 9 other tractors of various shape including an Oliver hart par.

Our favorite toy is our 1957 alise d14, it was a demonstraiter model, factory tach, cigarette lighter, gauges, its a pretty nice tractor but needs a rebuild. Shes still running and never been torn down and still used with the old brush hog on the farm, weved owned it since my grandpa traded a 56 chevy for it back in 1957.

DREAMS OF A 67 · 07-31-2008, 04:56 PM

FROM KNOXVILLE TN!!!

asphaltburner · 07-31-2008, 07:33 PM

Wowsers! walts_restoration! How cool!
When I bought my JD, the owners were pull starting it. I rebuilt the magneto and it has been hand-starting ever since. Turn that flywheel slow until it pops, then give it a spin,...pop, pop, pop, and off it goes! Even in the dead of winter! 1942 and never been rebuilt! Just works when ever it's needed!
Again, thanks to all of you for the nice welcome! I'd like to let y'all know that I have collected a number of vehicles, almost all of which I've rebuilt. I start with brakes and suspension, and work my way up.
In highschool I had a '53 Stude that I hurt badly, rebuilt, and then knew too much! Put a 327 and BW T10 4spd in front of a 4.55:1 rear and ruled the streets of Ft Collins, CO,...1973.
MANY years later (1992 and out of the Navy), I started with my '68 Mustang coupe, restored the '72 VW Superbeetle that we'd been driving for years, and salvaged and restored a '66 Mustang that was featured on Denver's Ch9 news (sold it after restoration to a doctor friend of mine). Snagged my '76 Camaro (that I commute with daily) and a '79 Fiat Spider 2000 conv. at about the same time in 2000 (both are restored, and the Camaro sports an identical 350 engine to the one I built for this truck,...410 ftlbs of torque and about 325 hp). I got my '69 Ford F100 from my dad-in-law for cheap (360 3spd with granny gear all original), and I FINALLY bought (for a stipend) the '88 Mazda RX-7 conv. 5spd That my dad bought with 10 miles on it in '88,...now with 44,610 original miles,...looks like it just rolled off the showroom floor!
A couple need paint 'cause I haven't had time to get back to THAT chore, but all are in perfect running order, and most have new engines, are covered and housed. Gotta show off the '66 Mustang that I painted because of 911, prior to it's restoration,...it was my daily driver for over five years,...primer red for three before this:

asphaltburner · 07-31-2008, 11:41 PM

Yo! Us old programmers,...sometimes we just get a method stuck in our heads! Lets try what Orange had directed in the first place! I have lots of pics!
This would be my 350 V8 and TH400 with the NP205 adapter:
Name: FRANKENTRUCK's 350TH400 001 (Medium).jpg
Views: 103
Size: 68.7 KB

Name: FRANKENTRUCK's 350TH400 001 (Medium).jpg
Views: 103
Size: 68.7 KB

Next, my most recent upholtery job:
Name: 072708 022 (Medium).jpg
Views: 106
Size: 57.4 KB

I'll bore you no more with my test of how to properly place pics in the post except for one last pic,...of my '76 Camaro (quite altered!!) that I commute 40 miles/day to Ft Collins and back with:
Name: blackcamarostealth (Medium).jpg
Views: 103
Size: 87.8 KB

Name: blackcamarostealth (Medium).jpg
Views: 103
Size: 87.8 KB

I AM proud of that one! Thank you for your indulgence. Todd.

Walts_restoration · 08-01-2008, 12:17 AM

Looking good man, i wish i could get that far on one of my projects.

68GMC454 · 08-01-2008, 03:38 AM

howdy and welcome... nice collection of toys you got there. i love old tractors... but i grew up on a farm, learned to drive on a ol ferguson 20 it think it was.... ahhhhh the good ol days..

asphaltburner · 08-01-2008, 11:26 PM

Yo! 68GMC454! I've got eleven all together that I've gathered, built, and collected, so I'll post some more pics! Thanks very much,...these are my babies,..."sweat equity" into each one!! Todd.

asphaltburner · 08-01-2008, 11:38 PM

Holy crap! There's a "DRUM BRAKE" club!!? My '72 VW Superbeetle has drum brakes! Swapped my '68 Mustang (and that '66) over to front discs so they could commute! Purchasing the front disc conversion for the bug this summer! Todd.

asphaltburner · 08-02-2008, 01:25 PM

Yo! Off I go to the '73-'87 forum,...

babyJay · 08-03-2008, 03:22 PM

Nice stuff! Welcome, from Indiana!

Walts_restoration · 08-03-2008, 03:28 PM

http://67-72chevytrucks.com/vboard/s...d.php?t=301610

heres his thread for those who wanna go find it.

07-31-2008, 01:01 AM	#1
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	New to this forum, old salt otherwise,... Yo! Y'all! Building a free (hauled from a cow pasture near Wyoming), nearly rust-free, '78 3/4 ton 4x4 P/U using my ol', rusty, beater, '73 3/4 ton 4x4 flatbed (from Missouri) as a donor. Out went the full-time 4x4 corporate front axle/spring combo in exchange for the flatbed's front spring assembly and Dana 44 with Warn locking hubs. Out went the 4120 lb rated rear spring/axle assembly in exchange for the flatbed's 5560 lb rated rear assembly. New tall tires and the P/U sits proud! Refurbished, or junkyard replaced, all that I could, and bought new for anything I couldn't. Built a 350 V8 that'll produce near 400 ftlbs of torque and about 325 hp, just like the one I run in my '76 Camaro that I built about 30,000 miles ago, and drive everyday to work. Had the P/U's only really fine part, a TH400, rebuilt by AAMCO. Added a new 1200-1500 stall speed converter and had them imstall a long output shaft (2WD version,...the 4WD version is "rare as the dodo"), and bought a modified twin stick, rebuilt, NP205 transfercase from Off Road Design in Carbondale, CO. to solve the tough shifting of the NP205 and allow me independant control of the front and rear axles. Also purchased the "rare as a dodo" reproduced TH400/NP205 aluminum adapter from the same source. The "bulletproof" NP205 as modified will allow me to shift on-the-fly and give me rear wheel high/low, 4x4 high/low, and FRONT wheel drive high/low! New grille, dashpad, floor covering (underlayment, 1/4" foil-backed wool, and full-floor vinyl,...after minor floor repairs), weatherstripping, and just finished re-upholstering the seat last Sunday in the near 100 degree heat,...damn hot, but sure made that vinyl contour nicely! Just finished electrical, and working on the fuel system now (aux tank was disconnected and is full of running rust! Donor flatbed's 20 gal tank will substitute nicely, and I pulled it tonight, I'll wash and dry it in the AM). A new six port valve will swap tanks and I'll add a small fuel gauge below the dash so I can monitor both tanks continuously. Nearing driveline installation,...then I'll measure, select the best of my front and rear driveshafts, and have them altered to fit the installation. Brand new steel hood awaits installation, as does a new rear chrome bumber to match the perfect front one. Glad to be here and I hope to contribute as much as I can by passing on the knowledge and techniques that I've learned over thirty plus years of repairing, building, and painting all types of cars and trucks. Todd, alias asphaltburner.

07-31-2008, 01:15 AM	#2
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	Re: New to this forum, old salt otherwise,... Welcome to the board from South Mississippi! __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

07-31-2008, 01:57 AM	#3
Walts_restoration Real Projects never die Join Date: Jan 2007 Location: Lawrence, kansas Posts: 1,508	Re: New to this forum, old salt otherwise,... hey man i think i know who you are :P people are gonna say it after me, so __________________ Ill put it this way, ive got a few lawn ornaments My name tag says Ryan KansasTwister On other forums Last edited by Walts_restoration; 07-31-2008 at 01:57 AM.

07-31-2008, 03:20 AM	#4
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Yo! walts-restoration! Yeah, yeah, yeah! My driver's fender is off right now for door alignment, and it's just not pic time yet,...gimme a couple days to get it right, and re-installed. Kinda embarassing looking at the moment! Lots to come! Todd.

07-31-2008, 06:44 AM	#5
Cyclone44 Step Brother Join Date: Sep 2007 Location: K-town Posts: 4,029	Re: New to this forum, old salt otherwise,... from Knoxville Tn...

07-31-2008, 09:51 AM	#6
jsbgump Gone Fishing Join Date: Aug 2005 Location: Fort Worth, Texas 76135 Posts: 12,361	Re: New to this forum, old salt otherwise,... Welcome to the board from Texas __________________ 68 Chevy Short Fleetside LSX Swap Under Way 3.73 posi 2.5/4 drop Frame of resto has been started 2022 Hyundai Tucson Limited 2019 Chevy Traverse Redline Edition Wifes Ride Build Thread http://67-72chevytrucks.com/vboard/s...=1#post3483616

07-31-2008, 10:34 AM	#7
shaneschevys Its always something! Join Date: Aug 2005 Location: FT Worth,TX Posts: 4,992	Re: New to this forum, old salt otherwise,... welcome from FT Worth TX. __________________ 79 p10 stepvan 72 Short Fleetside 72 Suburban 67 GMC One Ton Flatbed 64 Short Fleetside 57 Chevy 2DR Hard Top 57 Chevy 2dr wagon 65 f* short fleet 63 C 60 Flatbed Member of the patina club**

07-31-2008, 10:43 AM	#8
BACKYARD88 On the fast track to nowhere.. Join Date: May 2006 Location: Splendora, Texas Posts: 5,316	Re: New to this forum, old salt otherwise,... from South Texas! __________________ -Mike Owen- Support the board here! 71 Chevy short fleet build thread Double D Norwood, Houston, Cecilia, Jackson, Monroe and counting

07-31-2008, 10:55 AM	#9
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Yo! How 'bout this? Todd. Attached Images

07-31-2008, 12:24 PM	#10
Walts_restoration Real Projects never die Join Date: Jan 2007 Location: Lawrence, kansas Posts: 1,508	Re: New to this forum, old salt otherwise,... thats exzactly the truck im looking for man. an old 4x4 3/4 farm truck. Id hit it man. __________________ Ill put it this way, ive got a few lawn ornaments My name tag says Ryan KansasTwister On other forums

07-31-2008, 01:12 PM	#11
BigDaddyDave RIP BigDaddyDave ~7-23-09~ You will be missed~ Join Date: Aug 2007 Location: Concord NC Posts: 1,361	Re: New to this forum, old salt otherwise,... Welcome to the board from NC. __________________ BigDaddyDave's Truck: http://www.flickr.com/photos/daves71chevy/ \| See it in Action!

07-31-2008, 01:45 PM	#12
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Yo! walts_restoration! Glad you like my choice! I just got lucky that it was nearly abandoned out there with the cows,...didn't even have a rear window! BUT N Colorado/Wyoming wind and dry saved it! I expect that I'll have about $7000 into the whole project when I get to smoke all four wheels at once for the first time,...or maybe I'll put 'er in front wheel drive and scare some folks! Anyway, the factory fuel tanks (one from from each truck) are drying in my driveway right now, having found the cheap, aftermarket aux. tank full of running rust! Into the flatbed it went this AM to haul to the junkyard with all the other leftover crap,...it'll bring $100/ton when I'm done! That'll pay for the cost of flatbedding this '78 P/U to my house from the cow pasture! Sorry, I thought I had pics on nastz28.com but they could be on previous pages in my thread that you've not seen! More to come, and I will probably retire this thread, and head to the more appropriate forum soon,...isn't it 73-8?(something,...but oddly not '80) trucks forum? Todd.

07-31-2008, 01:52 PM	#13
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... And thanks to all for the kind welcome!! I'll try to take the time to help some of these members, if they'll let me. I've built alot of vehicles, and maintain eleven collected ones at the moment. Here's one of my favorites: Attached Images

07-31-2008, 02:00 PM	#14
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: New to this forum, old salt otherwise,... to the board from Mid-MO!!! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

07-31-2008, 03:08 PM	#15
Walts_restoration Real Projects never die Join Date: Jan 2007 Location: Lawrence, kansas Posts: 1,508	Re: New to this forum, old salt otherwise,... Love the old deere. My old mans got a 1938 John deere A on the farm, never been left outside or in the rain a day of its life, all near completely original, and about 9 other tractors of various shape including an Oliver hart par. Our favorite toy is our 1957 alise d14, it was a demonstraiter model, factory tach, cigarette lighter, gauges, its a pretty nice tractor but needs a rebuild. Shes still running and never been torn down and still used with the old brush hog on the farm, weved owned it since my grandpa traded a 56 chevy for it back in 1957. __________________ Ill put it this way, ive got a few lawn ornaments My name tag says Ryan KansasTwister On other forums



Register or Log In To remove these advertisements.

07-31-2008, 04:56 PM	#16
DREAMS OF A 67 Step Brother Join Date: Sep 2007 Location: knoxville TN Posts: 1,950	Re: New to this forum, old salt otherwise,... FROM KNOXVILLE TN!!! __________________ Joe

07-31-2008, 07:33 PM	#17
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Wowsers! walts_restoration! How cool! When I bought my JD, the owners were pull starting it. I rebuilt the magneto and it has been hand-starting ever since. Turn that flywheel slow until it pops, then give it a spin,...pop, pop, pop, and off it goes! Even in the dead of winter! 1942 and never been rebuilt! Just works when ever it's needed! Again, thanks to all of you for the nice welcome! I'd like to let y'all know that I have collected a number of vehicles, almost all of which I've rebuilt. I start with brakes and suspension, and work my way up. In highschool I had a '53 Stude that I hurt badly, rebuilt, and then knew too much! Put a 327 and BW T10 4spd in front of a 4.55:1 rear and ruled the streets of Ft Collins, CO,...1973. MANY years later (1992 and out of the Navy), I started with my '68 Mustang coupe, restored the '72 VW Superbeetle that we'd been driving for years, and salvaged and restored a '66 Mustang that was featured on Denver's Ch9 news (sold it after restoration to a doctor friend of mine). Snagged my '76 Camaro (that I commute with daily) and a '79 Fiat Spider 2000 conv. at about the same time in 2000 (both are restored, and the Camaro sports an identical 350 engine to the one I built for this truck,...410 ftlbs of torque and about 325 hp). I got my '69 Ford F100 from my dad-in-law for cheap (360 3spd with granny gear all original), and I FINALLY bought (for a stipend) the '88 Mazda RX-7 conv. 5spd That my dad bought with 10 miles on it in '88,...now with 44,610 original miles,...looks like it just rolled off the showroom floor! A couple need paint 'cause I haven't had time to get back to THAT chore, but all are in perfect running order, and most have new engines, are covered and housed. Gotta show off the '66 Mustang that I painted because of 911, prior to it's restoration,...it was my daily driver for over five years,...primer red for three before this: Attached Images

07-31-2008, 11:41 PM	#18
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Yo! Us old programmers,...sometimes we just get a method stuck in our heads! Lets try what Orange had directed in the first place! I have lots of pics! This would be my 350 V8 and TH400 with the NP205 adapter: Next, my most recent upholtery job: I'll bore you no more with my test of how to properly place pics in the post except for one last pic,...of my '76 Camaro (quite altered!!) that I commute 40 miles/day to Ft Collins and back with: I AM proud of that one! Thank you for your indulgence. Todd. Last edited by asphaltburner; 07-31-2008 at 11:43 PM.

08-01-2008, 12:17 AM	#19
Walts_restoration Real Projects never die Join Date: Jan 2007 Location: Lawrence, kansas Posts: 1,508	Re: New to this forum, old salt otherwise,... Looking good man, i wish i could get that far on one of my projects. __________________ Ill put it this way, ive got a few lawn ornaments My name tag says Ryan KansasTwister On other forums

08-01-2008, 03:38 AM	#20
68GMC454 THE VILLIAGE IDIOT Join Date: Nov 2006 Location: Tooele, Utah Posts: 1,405	Re: New to this forum, old salt otherwise,... howdy and welcome... nice collection of toys you got there. i love old tractors... but i grew up on a farm, learned to drive on a ol ferguson 20 it think it was.... ahhhhh the good ol days.. __________________ honestly honey,,i have no idea how that truck got here.

08-01-2008, 11:26 PM	#21
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Yo! 68GMC454! I've got eleven all together that I've gathered, built, and collected, so I'll post some more pics! Thanks very much,...these are my babies,..."sweat equity" into each one!! Todd.

08-01-2008, 11:38 PM	#22
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Holy crap! There's a "DRUM BRAKE" club!!? My '72 VW Superbeetle has drum brakes! Swapped my '68 Mustang (and that '66) over to front discs so they could commute! Purchasing the front disc conversion for the bug this summer! Todd. Last edited by asphaltburner; 08-01-2008 at 11:41 PM.

08-02-2008, 01:25 PM	#23
asphaltburner Registered User Join Date: Jul 2008 Location: Ault, Colorado Posts: 862	Re: New to this forum, old salt otherwise,... Yo! Off I go to the '73-'87 forum,...

08-03-2008, 03:22 PM	#24
babyJay Arrived on a Pale Horse Join Date: Mar 2007 Location: SnagTown Indiana Posts: 2,524	Re: New to this forum, old salt otherwise,... Nice stuff! Welcome, from Indiana! __________________ Jason 87 V30 350TBI/400 White w/Boss V-plow 89 R3500 CC SRW

08-03-2008, 03:28 PM	#25
Walts_restoration Real Projects never die Join Date: Jan 2007 Location: Lawrence, kansas Posts: 1,508	Re: New to this forum, old salt otherwise,... http://67-72chevytrucks.com/vboard/s...d.php?t=301610 heres his thread for those who wanna go find it. __________________ Ill put it this way, ive got a few lawn ornaments My name tag says Ryan KansasTwister On other forums

Register or Log In To remove these advertisements.