Heater Hose Support ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

PHOENIX · 12-02-2002, 04:20 PM

Im going to be replacing my heater hoses soon and was wondering how you guys support your hoses. Are there any brackets out there? My current setup have the hoses running from the pump and laying down on the wheel well then going to the heater core. Is there something I can do instead of laying on the wheel well.

PS: I hooked up my heater core this weekend and I have Heat! Its a good thing too I needed it today. "Look mom no more frosted windows."

**old Rusty C10** · 12-02-2002, 06:06 PM

the straps ya had originally was plastic. mine eventually dry rotted and snapped off. What i did to replace them was to use the strapping used for vent ducts and i put electrical tape over the bottom and top where the hoses made contact. this worked good and is great for a work truck or daily driver if ya cant find orginals

PHOENIX · 12-02-2002, 06:14 PM

What do the original straps look like? Pictures of clamps/supports would be great!

**old Rusty C10** · 12-02-2002, 07:18 PM

the ones i had kinda looked like the plastic wire tie things they use to tie cables together they were like a quarter inch wide and had a little thing on the back that connected it to the wheel well by pusng that into a small hole
on the older cars ( like a 74 Impala i once had) it was a metal kinda hook thing that the hoses sat in and held them against the wheel well

**swervin ervin** · 12-02-2002, 07:44 PM

Eddie,

when I added the stainless braid to my heater hoses, I made me some purdy new ones out of some stainless sheetmetal I had laying around. Polished them up real nice.

BTW, my old ones were the metal clip types that cliped to the fender well. They wouldn't fit around my new hoses so I just made me some.

ElGracho · 12-02-2002, 08:54 PM

The original clip in my 84 K10 and 86 C10 was metal and fit into a hole in the fenderwell and held both hoses. I replaced one of them and bought the replacement from GM for<$5. I'm sure they are still available.

PHOENIX · 12-03-2002, 12:40 PM

Sounds great. Ill check the dealer, if not Ill make my own.

littlebubba · 12-04-2002, 12:57 AM

Adel Clamps work real good for this ( get the aircraft type), or the plastic wire clamps if you go to an electrical supply house. Pop rivet or screws.
Or you can go all out and make your own out of aluminum billet stock.

12-02-2002, 04:20 PM	#1
PHOENIX Registered User Join Date: Oct 2002 Location: Phoenix, Arizona Posts: 4,703	Heater Hose Support ? Im going to be replacing my heater hoses soon and was wondering how you guys support your hoses. Are there any brackets out there? My current setup have the hoses running from the pump and laying down on the wheel well then going to the heater core. Is there something I can do instead of laying on the wheel well. PS: I hooked up my heater core this weekend and I have Heat! Its a good thing too I needed it today. "Look mom no more frosted windows." __________________ * AVOID: LOPER'S PERMORANCE / LOPERSPEED.COM OF PHOENIX, AZ & COTTMAN TRANSMISSION *

12-02-2002, 06:06 PM	#2
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,310	straps the straps ya had originally was plastic. mine eventually dry rotted and snapped off. What i did to replace them was to use the strapping used for vent ducts and i put electrical tape over the bottom and top where the hoses made contact. this worked good and is great for a work truck or daily driver if ya cant find orginals __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

12-02-2002, 06:14 PM	#3
PHOENIX Registered User Join Date: Oct 2002 Location: Phoenix, Arizona Posts: 4,703	What do the original straps look like? Pictures of clamps/supports would be great! __________________ * AVOID: LOPER'S PERMORANCE / LOPERSPEED.COM OF PHOENIX, AZ & COTTMAN TRANSMISSION *

12-02-2002, 07:18 PM	#4
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,310	straps the ones i had kinda looked like the plastic wire tie things they use to tie cables together they were like a quarter inch wide and had a little thing on the back that connected it to the wheel well by pusng that into a small hole on the older cars ( like a 74 Impala i once had) it was a metal kinda hook thing that the hoses sat in and held them against the wheel well __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

12-02-2002, 07:44 PM	#5
swervin ervin You get what you pay for Join Date: Dec 1999 Location: Cherryville, NC Posts: 4,798	Eddie, when I added the stainless braid to my heater hoses, I made me some purdy new ones out of some stainless sheetmetal I had laying around. Polished them up real nice. BTW, my old ones were the metal clip types that cliped to the fender well. They wouldn't fit around my new hoses so I just made me some. __________________ Mike 1985 Chevy C-10

12-02-2002, 08:54 PM	#6
ElGracho Gentleman Jim Driver Join Date: Nov 2002 Location: Poulsbo, WA Posts: 1,553	The original clip in my 84 K10 and 86 C10 was metal and fit into a hole in the fenderwell and held both hoses. I replaced one of them and bought the replacement from GM for<$5. I'm sure they are still available. __________________ Joe '75 GMC Gentleman Jim '84 Chev C10 Short Wide - Super duper plain (manual steering, manual brakes, no dome light, no cig lighter) '85 Chev C10 Short Wide - Super plain Vortec 4.8 4L60E trans also: '81 K30, '83 C30 Crew Dually, '84 M1028 CUCV, '85 M1009 CUCV, another '85 C10 SWB, '89 R3500 Flatbed

12-03-2002, 12:40 PM	#7
PHOENIX Registered User Join Date: Oct 2002 Location: Phoenix, Arizona Posts: 4,703	Sounds great. Ill check the dealer, if not Ill make my own. __________________ * AVOID: LOPER'S PERMORANCE / LOPERSPEED.COM OF PHOENIX, AZ & COTTMAN TRANSMISSION *

12-04-2002, 12:57 AM	#8
littlebubba Registered User Join Date: Jun 2002 Location: Clinton Twp., Michigan Posts: 321	Clamps Adel Clamps work real good for this ( get the aircraft type), or the plastic wire clamps if you go to an electrical supply house. Pop rivet or screws. Or you can go all out and make your own out of aluminum billet stock.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.