Specs needed - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hard Luck · 04-06-2009, 07:06 PM

I just have an easy question. Need the upper ball joint bolt torque specs and the spec for the castle nut at spindle.

I have the service manual but it has all the numbers crossed out and refers me to an update that is not in the book.

Thanks

Hard Luck · 04-06-2009, 07:13 PM

Sorry, forgot. 69 Chev c-10 with drums. Thanks again.

chevydog66 · 04-06-2009, 10:26 PM

Wild guess, about 75-95 lb. ft. tq. Wheel studs are about 85 -95 for a 1/2" wheel stud.

Hard Luck · 04-08-2009, 12:25 AM

O.K. I got it. 10ft/lbs on the 1/4" bolts at the A-arm. 65ft/lbs on the castle nut on the spindle. Thanks.

chevydog66 · 04-09-2009, 02:30 AM

ya somewhere around here there is a tq. spec chart. Just make it tight. Dont back it off. you will lose the preload if u do.

*Shane* · 04-09-2009, 10:05 AM

tighten the spindle nut while spinning the rotor ... tighten until rotor will NOT free-wheel ... back off spindle nut to the closest cotter pin hole.

Mechanics have been using this method for YEARS with most not even knowing what "pre-load" is.

Sorry, but can't help on the ball joint fasteners. I can't see where it would be that critical considering the bolt really have nothing to do with the movement mechanism of the ball joint. But that's just an assumption on my part.

04-06-2009, 07:06 PM	#1
Hard Luck I've got grease on my mind. Join Date: Sep 2007 Location: Oly, Wa Posts: 481	Specs needed I just have an easy question. Need the upper ball joint bolt torque specs and the spec for the castle nut at spindle. I have the service manual but it has all the numbers crossed out and refers me to an update that is not in the book. Thanks

04-06-2009, 07:13 PM	#2
Hard Luck I've got grease on my mind. Join Date: Sep 2007 Location: Oly, Wa Posts: 481	Re: Specs needed Sorry, forgot. 69 Chev c-10 with drums. Thanks again.

04-06-2009, 10:26 PM	#3
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Specs needed Wild guess, about 75-95 lb. ft. tq. Wheel studs are about 85 -95 for a 1/2" wheel stud. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

04-08-2009, 12:25 AM	#4
Hard Luck I've got grease on my mind. Join Date: Sep 2007 Location: Oly, Wa Posts: 481	Re: Specs needed O.K. I got it. 10ft/lbs on the 1/4" bolts at the A-arm. 65ft/lbs on the castle nut on the spindle. Thanks.

04-09-2009, 02:30 AM	#5
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Specs needed ya somewhere around here there is a tq. spec chart. Just make it tight. Dont back it off. you will lose the preload if u do. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

04-09-2009, 10:05 AM	#6
Shane Account Suspended Join Date: Jun 2000 Location: over yonder Posts: 14,270	Re: Specs needed tighten the spindle nut while spinning the rotor ... tighten until rotor will NOT free-wheel ... back off spindle nut to the closest cotter pin hole. Mechanics have been using this method for YEARS with most not even knowing what "pre-load" is. Sorry, but can't help on the ball joint fasteners. I can't see where it would be that critical considering the bolt really have nothing to do with the movement mechanism of the ball joint. But that's just an assumption on my part.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.