|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-14-2009, 09:26 PM
|
#1 |
|
Registered User
 Join Date: Jan 2007
Location: Cabot, Arkansas
Posts: 72
|
Need help with HEADERS
I have a 72 4x4 blazer. It has a mid 70's 350 small block, with a 4spd manual tranny. I am looking for a set of headers (ceramic coated) that are not that long.....like hanging below the frame...some that tuck up ...but also a good pair. Any help would be greatly appreciated
|
|
|
|
09-14-2009, 10:44 PM
|
#2 | |
|
Registered User
Join Date: Jun 2009
Location: Diamond Bar, Ca
Posts: 94
|
Re: Need help with HEADERS
Quote:
__________________
72 K5 CST |
|
|
|
|
|
09-15-2009, 09:47 AM
|
#3 |
|
Registered User
Join Date: Feb 2000
Location: Modesto, CA
Posts: 1,842
|
Re: Need help with HEADERS
Yes, the Hedmen Elite is what I ran and they tuck up nice and high. I had to move the frame side of the Z-bar towards the firewall about 1". Easy as drilling a hole and moving the ball stud mount.
With the Elite series the flanges are nice and thick wich keeps them from warping.  
__________________
1972 K5 MPFI454/Sm465/Np205/D60/14FFd/Re-Centerd H1s w/Swamper Iroks 
|
|
|
|
|
09-15-2009, 11:23 AM
|
#4 |
|
Rottenwood Garage Member
Join Date: May 2005
Location: Marietta, Georgia
Posts: 4,321
|
Re: Need help with HEADERS
"Need help with HEADERS"
Unfortunatley most of WITH them do too!
__________________
2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! It's not just a hobby..It's a LIFESTYLE!!! Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere! |
|
|
|
|
09-15-2009, 05:49 PM
|
#5 | |
|
Registered User
Join Date: Jun 2009
Location: Diamond Bar, Ca
Posts: 94
|
Re: Need help with HEADERS
Quote:
__________________
72 K5 CST |
|
|
|
|
|
09-16-2009, 09:00 PM
|
#6 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: Need help with HEADERS
Yup. Heddmans. When I did headers on mine eons ago, they were the only ones I could find that would work with the manual trans. You might be able to run Corvette full length headers as they are really close to the same size. BUT, I ditched mine for the 2 1/2" rams horns, and that would be my suggestion to you if you haven't spent the money yet. With the Crane 266 cam in mine, it is pretty much done by 4500 rpm. The full 2 1/2" exhaust with manifolds pulls just as hard or harder than the header exhaust did. And it is much quieter. And not leak prone.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
