Clutch linkage question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

69Chevyc10 · 01-29-2003, 06:36 PM

I have a 69 c10 it had a 292 with a three on the tree. The six cyl is out and I have a 350 for it. Im using the same tranny. Will the Clutch linkage work from the 292 or not. Can you tell me what I need to get. Thanks Brian Wolf

crazy longhorn · 01-29-2003, 06:51 PM

If you are mounting in I 6 position with the sb, the 250 eng stands will work(you will need to change the pass side stand). Mounted in I6/250 position with my sb, here is what worked for me.......I used all of the v8 clutch linkage, & instead of the bolt on bracket/pivot ball , I used a screw in pivot ball in the foward hole on the block. Then the bell crank was set up perpendicular with the eng, & the holes were redrilled for the frame bracket (again the v8 pc). The lenght of the bottom rod then had to modified. set up like that , I ran a set of 69090 Hedman headers, & all the linkage cleared. I couldnt say about the column shift linkage, as I ran a floor shifter. Good luck.....crazyL

toms68cst · 01-30-2003, 12:18 AM

Brian, If you are in Bismarck some time, stop over at my house. You can look at my 327 clutch linkage set up if you want. I've got my engine out for a rebuild right now.

Drop a PM sometime.

69Chevyc10 · 01-30-2003, 01:44 AM

Sure I will be in Bis on the 30th. If your around I would sure like to step by and take a look. I always wanted to find some guys in Bis that are into our style trucks. You could give me your phone #. Then we could set up at time and date to meet.
....Brian wolf

toms68cst · 01-30-2003, 09:27 AM

Sure, I'll be around.

I sent you an e-mail with the info.

Tom.

Slammed67 · 05-28-2003, 04:16 PM

Hey Brian,

You still owe me $60.00!!! Pay up!

01-29-2003, 06:36 PM	#1
69Chevyc10 Registered User Join Date: Mar 2002 Location: ND USA Posts: 122	Clutch linkage question I have a 69 c10 it had a 292 with a three on the tree. The six cyl is out and I have a 350 for it. Im using the same tranny. Will the Clutch linkage work from the 292 or not. Can you tell me what I need to get. Thanks Brian Wolf

01-29-2003, 06:51 PM	#2
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	If you are mounting in I 6 position with the sb, the 250 eng stands will work(you will need to change the pass side stand). Mounted in I6/250 position with my sb, here is what worked for me.......I used all of the v8 clutch linkage, & instead of the bolt on bracket/pivot ball , I used a screw in pivot ball in the foward hole on the block. Then the bell crank was set up perpendicular with the eng, & the holes were redrilled for the frame bracket (again the v8 pc). The lenght of the bottom rod then had to modified. set up like that , I ran a set of 69090 Hedman headers, & all the linkage cleared. I couldnt say about the column shift linkage, as I ran a floor shifter. Good luck.....crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

01-30-2003, 12:18 AM	#3
toms68cst Registered User Join Date: Jun 2000 Location: Bismarck, ND Posts: 4,300	Brian, If you are in Bismarck some time, stop over at my house. You can look at my 327 clutch linkage set up if you want. I've got my engine out for a rebuild right now. Drop a PM sometime. __________________ Unrestored 68 C-10 CST. Original 327. 4-Speed CH465. 50k or so miles. TREASURER, Drum Brake Club.

01-30-2003, 01:44 AM	#4
69Chevyc10 Registered User Join Date: Mar 2002 Location: ND USA Posts: 122	linkage Sure I will be in Bis on the 30th. If your around I would sure like to step by and take a look. I always wanted to find some guys in Bis that are into our style trucks. You could give me your phone #. Then we could set up at time and date to meet. ....Brian wolf

01-30-2003, 09:27 AM	#5
toms68cst Registered User Join Date: Jun 2000 Location: Bismarck, ND Posts: 4,300	Sure, I'll be around. I sent you an e-mail with the info. Tom. __________________ Unrestored 68 C-10 CST. Original 327. 4-Speed CH465. 50k or so miles. TREASURER, Drum Brake Club.

05-28-2003, 04:16 PM	#6
Slammed67 Progress = 0% Join Date: Nov 2001 Location: Kansas City, MO Posts: 2,108	Hey Brian, You still owe me $60.00!!! Pay up! __________________ Jason - '67 GMC swb \| '57 Bel-Air 4dr hardtop \| '56 210 4dr Wagon \| 2000 GMC Sierra



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.