|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-01-2010, 08:33 PM
|
#1 |
|
Registered User
Join Date: Feb 2010
Location: greenville, sc
Posts: 58
|
shifter bushings on linkage to tranny?
my 3 speed will not shift smoothly... i tightened it up via with the screws removed ect ect from under the hood.. you know.. under the master cylinder... but i notcied the arms going to the tranny are REALLY SLOPPY .. do the make a bushing or some sort of sleeve for this.. i looked at lmc and tryed searching for it and to no avail im beginning to believe there is nothing that is supposed to be there
|
|
|
|
03-01-2010, 08:54 PM
|
#2 |
|
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: shifter bushings on linkage to tranny?
I got bushings from the local Chevy dealer.
Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
|
|
|
|
03-01-2010, 08:56 PM
|
#3 |
|
Registered User
Join Date: Feb 2010
Location: greenville, sc
Posts: 58
|
Re: shifter bushings on linkage to tranny?
so im not retarded... there is supposed to be some kind of bushing there
|
|
|
|
|
03-01-2010, 08:58 PM
|
#4 |
|
Watch out for your cornhole !
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: shifter bushings on linkage to tranny?
I got mine from Classic Parts.
__________________
I'm on the Instagram- @Gearhead_Kevin |
|
|
|
|
03-01-2010, 09:22 PM
|
#5 |
|
Registered User
Join Date: Jun 2009
Location: Newnan, GA
Posts: 485
|
Re: shifter bushings on linkage to tranny?
the bushings i had on mine were pretty small, one is flat the other has a metal backing and the front portion goes into the whole around the retainer with a cariter pin. i need to replace mine but i have not looked for them
__________________
 Learning as I go! ------------------------------------- |
|
|
|
|
03-01-2010, 09:55 PM
|
#6 |
|
Moderator
 
Join Date: May 2007
Location: Southern Cal
Posts: 20,058
|
Re: shifter bushings on linkage to tranny?
www.truckandcarshop.com has them also.
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
|
03-01-2010, 10:19 PM
|
#7 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: shifter bushings on linkage to tranny?
my local hardware store has nice brone bushings in a variety of sizes// you do need to know how to measure to select the right ones
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
03-01-2010, 10:42 PM
|
#8 |
|
Registered User
Join Date: Feb 2010
Location: greenville, sc
Posts: 58
|
Re: shifter bushings on linkage to tranny?
is this them?
http://www.classicparts.com/1960-76-...ctinfo/91-063/ |
|
|
|
|
03-01-2010, 10:48 PM
|
#9 |
|
Registered User
Join Date: Feb 2010
Location: greenville, sc
Posts: 58
|
Re: shifter bushings on linkage to tranny?
wait maybe im not clear lol... i am talking about where the arm goes down and is like 3 inches from the side of the tranny...where that arms attaches to the levers
|
|
|
|
|
03-01-2010, 10:52 PM
|
#10 |
|
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: shifter bushings on linkage to tranny?
Those are the ones I used on my truck. You need two of them.
__________________
I'm on the Instagram- @Gearhead_Kevin |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
