What did you get done 11/21/2010 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**old Rusty C10** · 11-21-2010, 04:52 PM

I didnt get much done how about you all?

knightowl73 · 11-21-2010, 04:59 PM

for me was day 3 of putting new inner lower door and door skins on a buddy's '72 project. tommorrow ill start bondo work on it. was a longbed that he cut down to make a shorty. going pretty well. hpefully ill be done with everything by friday, have to bondo the bed where he spliced it still.

Gary66 · 11-21-2010, 05:47 PM

I got some stuff done- i changed ALL fluids in the K10- oil-trans-power steering-coolant-brake-and rear end oil- put an Edelbrock 1406 on and it runs 10x better than the old quadrajet, and had all new exhaust put on-

**PRattenbury** · 11-21-2010, 05:51 PM

I assembled an engine crane. Didn't do anything to the truck directly.

HOGDADDY · 11-21-2010, 06:07 PM

Hooked up stock radio with 2 nos front speakers and 2 universal rear 4 x 10 speakers from this guy http://www.turnswitch.com/speakers.htm

They fit in the stock brakets perfect. Radio sounds ok for stock.

AceX · 11-21-2010, 06:17 PM

Getting ready to start another 10+ hour shift. 2 more weeks and I'll be back home. Santa Rosa is boring...

qu1cks1lver56 · 11-21-2010, 06:34 PM

waxed mom's new car

RuralRoute C-30 · 11-21-2010, 07:05 PM

Learned how to R&R the inner door panel on our Saturn 3-door coupe, electric window got stuck in the down position Thursday. Fixed. (thanks to 'you tube' actually)

Last week-end of this year that I'm wasting fuel for mulching leaves.

Also was the last and final run of this year for firewood with the truck and trailer Saturday. Today stacked wood in the crib and our garage in preparation for the beginning of winter. Still have a trailer to unload sometime.

Looking forward to a long Thanksgiving week-end off from the day job! Hope to start cleaning up the C-30 engine this week. Still gathering parts for the upcoming fuel delivery system rehab project with a refreshed engine compartment. Always something to do or I'd be dead.

Mark

GMC91 · 11-21-2010, 07:15 PM

Didnt get nothing done, had my tonsils removed so I have been laid up. But after I get over this, work will begin back on my 76.

85burb · 11-21-2010, 08:14 PM

I got quite a bit done today. I painted my block yesterday and installed all the covers and new plugs in it today. Also installed my accecory bracket.

S10Fan · 11-21-2010, 08:55 PM

Started the rust repairs on my newly acquired '50 Chevy. Test fitted the outer cowl panel and welded in the right side floor panel.

**PRattenbury** · 11-21-2010, 09:06 PM

Looks like fun stuff. Do you have a nice big shop to do all that stuff in?

S10Fan · 11-21-2010, 09:16 PM

Quote:

Originally Posted by PRattenbury

Looks like fun stuff. Do you have a nice big shop to do all that stuff in?

Nah, the garage is 18X30 but it sure does look bigger with just the cab in there. LOL.

1tonchevy · 11-21-2010, 09:18 PM

Got my 89 C/K Jimmy Rear bumper,front air dam and steering wheel installed on my Dually

80stepsideguy · 11-21-2010, 09:39 PM

Well i ordered some parts for the 80.I got a pair of LED stepside taillights on order n hopefully they`ll be here next week.Also ordered some stuff for the engine, and should have a package comming from brothers this week to help assemble the rear bumper.Tried to test fit the radiator NOPE to small. Talked to the guy, gonna ship it next week for a correct 1(my bad not his).Ordered some parts for my 70 cougar, overall spent some money and not alot accomplished.Oh also sent out more parts for powdercoating.

thanks
pat

**N2TRUX** · 11-21-2010, 09:49 PM

I worked yesterday so I didn't get much done. Today I rewired a Bro-in-laws utility trailer because his dog hate the harness up. After that I spent some time organizing all the parts I bought last week. Later I pulled the seat in my 77 so I could remove the Ride Tech E3 ECU. It is going back to Ride Tech for updates.

I sold the 12 bolt, and wiring harness kit. I listed a pair of 73-80 fenders- LINK

**N2TRUX** · 11-21-2010, 10:06 PM

Quote:

Originally Posted by S10Fan

Started the rust repairs on my newly acquired '50 Chevy. Test fitted the outer cowl panel and welded in the right side floor panel.

Looks like your all in to it. Have you seen this thread on Lateral G? NSANE 52' Chevy Truck- LINK

*87 chevy silverado* · 11-21-2010, 10:13 PM

went to pull a part an got the passenger door wire harness for the locks on power windows. one of the connections decided to brake when i pulled the door panel off. an i got the switches to they look brand new o and the best part dad got me e early Christmas present a battery also at the yard i got a battery hold down cramp.

an i help strip a 69 ferd... got more pics to come if i can get them uploaded an if any one want to c more

centexan · 11-21-2010, 10:14 PM

Took a trip to the pik-n-pull in San Antonio and made out well. Got a dang near mint dash pad for my Jimmy. It's dusty but there are no cracks, no scratches, nada. Heck of a deal for $15 bucks. Got a factory floor mat for the front of the cab, some assorted aluminum trim pieces and a nice glove box. All in all pretty successful trip.

S10Fan · 11-21-2010, 10:17 PM

Quote:

Originally Posted by N2TRUX

Have you seen this thread on Lateral G? NSANE 52' Chevy Truck- LINK

Wow!

Thanks for the link!

Grande Rojo · 11-21-2010, 10:25 PM

Well since my 77' is now done I went and bought a 67' today.

"winter project"

I pick it up tomorrow so, no pics yet.

zimmstoy · 11-21-2010, 10:32 PM

centexan - were the yards in San Antonio any good overall?

Got the 87 running again. Nice and smooth. Timing was slightly off. Smooth as silk now!

Degreased and powerwashed the 2WD Frame for the 74 Jimmy Conversion

centexan · 11-21-2010, 10:39 PM

Quote:

Originally Posted by zimmstoy

centexan - were the yards in San Antonio any good overall?

Got the 87 running again. Nice and smooth. Timing was slightly off. Smooth as silk now!

Degreased and powerwashed the 2WD Frame for the 74 Jimmy Conversion

I only went to the pik-n-pull today and it was ok. There a lot of square bodies, but pretty picked over. I just luck out when I go. Last time I went I got a center console like the two you have for your 74. I guess it depends on what you're looking for. I haven't ever been to any of the other ones. Are they pretty good too?

foamypirate · 11-21-2010, 10:58 PM

Pulled the cluster out and replaced all the dash lights so I can see my speedometer, oil pressure, volts, and engine temp at night! Of course, now my tachometer doesn't light up.

flamingbig10 · 11-22-2010, 12:48 AM

This weekend I replaced the upper and lower intake gaskets on my moms 03 Pontiac grand prix and I got the crank pulley off and the cam pulled out of the 6.0

11-21-2010, 04:52 PM	#1
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,316	What did you get done 11/21/2010 I didnt get much done how about you all? __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

11-21-2010, 04:59 PM	#2
knightowl73 TUKE-NoBullChit Customs owner Join Date: Feb 2010 Location: La Marque, Tx Posts: 640	Re: What did you get done 11/21/2010 for me was day 3 of putting new inner lower door and door skins on a buddy's '72 project. tommorrow ill start bondo work on it. was a longbed that he cut down to make a shorty. going pretty well. hpefully ill be done with everything by friday, have to bondo the bed where he spliced it still. __________________ OWNER @ NBC Customs...No Bull Chit....'92 GMC C2500 ECSB 350/TH400, '57 FORD SKYLINER (My dad's for now, but its really mine-you'll NEVER see a cooler car at 7 years old lol), '42 ford rat rod shop truck (new project), 91 CHRYSLER VOYER MINIVAN (shop van for now) http://www.facebook.com/#!/nbc.customs

11-21-2010, 05:47 PM	#3
Gary66 Registered User Join Date: Jan 2002 Location: anna, Illinois Posts: 308	Re: What did you get done 11/21/2010 I got some stuff done- i changed ALL fluids in the K10- oil-trans-power steering-coolant-brake-and rear end oil- put an Edelbrock 1406 on and it runs 10x better than the old quadrajet, and had all new exhaust put on- __________________ 2003 2500 HD Crew Cab 1965 GMC K10 1972 Chevrolet k5 blazer

11-21-2010, 05:51 PM	#4
PRattenbury Senior Member Join Date: Feb 2010 Location: Maumelle, AR Posts: 478	Re: What did you get done 11/21/2010 I assembled an engine crane. Didn't do anything to the truck directly.

11-21-2010, 06:07 PM	#5
HOGDADDY Registered User Join Date: Jul 2006 Location: Alabama Posts: 661	Re: What did you get done 11/21/2010 Hooked up stock radio with 2 nos front speakers and 2 universal rear 4 x 10 speakers from this guy http://www.turnswitch.com/speakers.htm They fit in the stock brakets perfect. Radio sounds ok for stock. Last edited by HOGDADDY; 11-21-2010 at 06:07 PM.

11-21-2010, 06:17 PM	#6
AceX >130dB Moderator Join Date: Aug 2006 Location: Sacramento, CA Posts: 2,130	Re: What did you get done 11/21/2010 Getting ready to start another 10+ hour shift. 2 more weeks and I'll be back home. Santa Rosa is boring... __________________ Living Life @ 130dB LED Tail Light Conversion; How-to Friend. Father. Brother. RIP El Jay ------------------------------------------------------------------------------------------------------------------------- CLICK HERE and for less than $0.07 a day, you too can help support and build a better forum.

11-21-2010, 06:34 PM	#7
qu1cks1lver56 Registered User Join Date: Dec 2009 Location: Milton, FL Posts: 733	Re: What did you get done 11/21/2010 waxed mom's new car __________________ My 86 http://67-72chevytrucks.com/vboard/s...d.php?t=375526

11-21-2010, 07:05 PM	#8
RuralRoute C-30 Registered User Join Date: Jan 2010 Location: East Central Illinois Posts: 511	Re: What did you get done 11/21/2010 Learned how to R&R the inner door panel on our Saturn 3-door coupe, electric window got stuck in the down position Thursday. Fixed. (thanks to 'you tube' actually) Last week-end of this year that I'm wasting fuel for mulching leaves. Also was the last and final run of this year for firewood with the truck and trailer Saturday. Today stacked wood in the crib and our garage in preparation for the beginning of winter. Still have a trailer to unload sometime. Looking forward to a long Thanksgiving week-end off from the day job! Hope to start cleaning up the C-30 engine this week. Still gathering parts for the upcoming fuel delivery system rehab project with a refreshed engine compartment. Always something to do or I'd be dead. Mark __________________ 1985 Chevy C-30 Hydraulic Dump Bed 2001 Saturn SC2 (go to work car) 2010 PT Cruiser (wife's car) "Reality is just a hallucination brought on by lack of alcohol."

11-21-2010, 07:15 PM	#9
GMC91 Always trouble Join Date: Jul 2009 Location: Hartsellle, Al Posts: 1,111	Re: What did you get done 11/21/2010 Didnt get nothing done, had my tonsils removed so I have been laid up. But after I get over this, work will begin back on my 76. __________________ 91 Silverado Regular cab, 2wd, swb-project truck 97 Silverado Extended cab, 2wd, swb-driver

11-21-2010, 08:14 PM	#10
85burb Registered User Join Date: Dec 2009 Location: lindale,tx Posts: 2,373	Re: What did you get done 11/21/2010 I got quite a bit done today. I painted my block yesterday and installed all the covers and new plugs in it today. Also installed my accecory bracket. Attached Images __________________ 82 c10 5.3/4l60 84 c20 5.3/sm465 85 chevy k10 suburban LQ4/4l60 91 chevy c10 suburban Lsa 5.3/4l60 2017 Silverado whipple 5.3 1964 Vw beetle 1974 vw beetle

11-21-2010, 08:55 PM	#11
S10Fan Old Heap Driver Join Date: Mar 2008 Location: Newport News, Va Posts: 2,642	Re: What did you get done 11/21/2010 Started the rust repairs on my newly acquired '50 Chevy. Test fitted the outer cowl panel and welded in the right side floor panel. Attached Images __________________ _____________________________ Bryan '99 Silverado 1500, 4.3, 5-speed, reg cab, short bed '50 Chevy 2DR Hard Top, 350/350, M2 Front End, 3:08 gear, cruiser. '40 F**d Sedan, all Chevy power, Heidt's front end, TCI rear, nice driver.

11-21-2010, 09:06 PM	#12
PRattenbury Senior Member Join Date: Feb 2010 Location: Maumelle, AR Posts: 478	Re: What did you get done 11/21/2010 Looks like fun stuff. Do you have a nice big shop to do all that stuff in?

11-21-2010, 09:18 PM	#14
1tonchevy C35 Crew Dually Join Date: Nov 2008 Location: Belleville Ontario Posts: 1,116	Re: What did you get done 11/21/2010 Got my 89 C/K Jimmy Rear bumper,front air dam and steering wheel installed on my Dually __________________ If it aint square, I don't care. 84 C35 CC Dually Project log... http://67-72chevytrucks.com/vboard/s...d.php?t=414892

11-21-2010, 09:39 PM	#15
80stepsideguy Laid back freak Join Date: Mar 2008 Location: hastings florida Posts: 248	Re: What did you get done 11/21/2010 Well i ordered some parts for the 80.I got a pair of LED stepside taillights on order n hopefully they`ll be here next week.Also ordered some stuff for the engine, and should have a package comming from brothers this week to help assemble the rear bumper.Tried to test fit the radiator NOPE to small. Talked to the guy, gonna ship it next week for a correct 1(my bad not his).Ordered some parts for my 70 cougar, overall spent some money and not alot accomplished.Oh also sent out more parts for powdercoating. thanks pat __________________ 1980 chevy c10 step side restomod, 1970 cougar convertible 1 OF 24 ever built: 2014 Hyundai Tucson limited (daily driver).

11-21-2010, 09:49 PM	#16
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: What did you get done 11/21/2010 I worked yesterday so I didn't get much done. Today I rewired a Bro-in-laws utility trailer because his dog hate the harness up. After that I spent some time organizing all the parts I bought last week. Later I pulled the seat in my 77 so I could remove the Ride Tech E3 ECU. It is going back to Ride Tech for updates. I sold the 12 bolt, and wiring harness kit. I listed a pair of 73-80 fenders- LINK Attached Images __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"



Register or Log In To remove these advertisements.

11-21-2010, 10:13 PM	#18
87 chevy silverado Account Suspended Join Date: Apr 2009 Location: lexington South Carolina Posts: 2,124	Re: What did you get done 11/21/2010 went to pull a part an got the passenger door wire harness for the locks on power windows. one of the connections decided to brake when i pulled the door panel off. an i got the switches to they look brand new o and the best part dad got me e early Christmas present a battery also at the yard i got a battery hold down cramp. an i help strip a 69 ferd... got more pics to come if i can get them uploaded an if any one want to c more

11-21-2010, 10:14 PM	#19
centexan Registered User Join Date: Aug 2006 Location: Austin, Texas Posts: 167	Re: What did you get done 11/21/2010 Took a trip to the pik-n-pull in San Antonio and made out well. Got a dang near mint dash pad for my Jimmy. It's dusty but there are no cracks, no scratches, nada. Heck of a deal for $15 bucks. Got a factory floor mat for the front of the cab, some assorted aluminum trim pieces and a nice glove box. All in all pretty successful trip. __________________ 1989 Chevy Suburban v1500

11-21-2010, 10:25 PM	#21
Grande Rojo paper or plastic? Join Date: Nov 2002 Location: SW Missouri Posts: 671	Re: What did you get done 11/21/2010 Well since my 77' is now done I went and bought a 67' today. "winter project" I pick it up tomorrow so, no pics yet. __________________ 1967 Chevy SWB 250 http://67-72chevytrucks.com/vboard/s...d.php?t=442157 1977 Chevy SWB 454 No More 454 getting 5.3 http://67-72chevytrucks.com/vboard/s...d.php?t=310518 1977 Stepside Truck of the month winner http://67-72chevytrucks.com/vboard/s...d.php?t=135524 1965 Chevy C10 454 http://67-72chevytrucks.com/vboard/s...d.php?t=731372 1975 Dodge Power Wagon http://67-72chevytrucks.com/vboard/s...=1#post7871388

11-21-2010, 10:32 PM	#22
zimmstoy Registered User Join Date: Feb 2008 Location: Cedar Park, TX Posts: 214	Re: What did you get done 11/21/2010 centexan - were the yards in San Antonio any good overall? Got the 87 running again. Nice and smooth. Timing was slightly off. Smooth as silk now! Degreased and powerwashed the 2WD Frame for the 74 Jimmy Conversion __________________ Kind Regards, Scott Last edited by zimmstoy; 11-21-2010 at 10:33 PM.

11-21-2010, 10:58 PM	#24
foamypirate Registered User Join Date: Apr 2009 Location: Pflugerville, TX Posts: 594	Re: What did you get done 11/21/2010 Pulled the cluster out and replaced all the dash lights so I can see my speedometer, oil pressure, volts, and engine temp at night! Of course, now my tachometer doesn't light up.

11-22-2010, 12:48 AM	#25
flamingbig10 6.0 powered square Join Date: Feb 2008 Location: Mesquite texas Posts: 3,459	Re: What did you get done 11/21/2010 This weekend I replaced the upper and lower intake gaskets on my moms 03 Pontiac grand prix and I got the crank pulley off and the cam pulled out of the 6.0 __________________ Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 Last edited by flamingbig10; 11-22-2010 at 12:50 AM.

Register or Log In To remove these advertisements.