alignment ?s - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cb1965 · 12-08-2010, 08:59 PM

is there a way to closely allign my front end. i dont want to go to a shop

until i get new wheels on.but i want to be able to drive it on test drives while

im working on it.

p.s. its a 76 suspension and im putting in new tie rods.

**Clyde65** · 12-08-2010, 09:14 PM

Unless ur current tires are bad, I would align it, if you take it to Firestone, you can get a 1 time align or a lifetime align, might be worth it if your roads are bad where you live.

**TR65** · 12-08-2010, 09:35 PM

CB,

Check out this thread.

http://67-72chevytrucks.com/vboard/s...ight=alignment

and this one

http://67-72chevytrucks.com/vboard/s...ight=alignment

TR

ChopperDr · 12-08-2010, 11:23 PM

I'm assuming the '76 suspension has discs. Here's how I do it: Pull the wheels off and support the a-arms at ride height. Pull a string along the rotor face. The strings can be pulled out in front of the truck so you cam measure between them to set toe. Eyeball the camber and don't worry too much about caster. This method will get it drivable. Its fun to see how close you can get them with this method.

Chop

bama63 · 12-08-2010, 11:44 PM

remove the dust cap and use a torpedo level to set the camber and use a tape measure and a friend to measure the toe

12-08-2010, 08:59 PM	#1
cb1965 Registered User Join Date: Mar 2010 Location: san jose, california Posts: 508	alignment ?s is there a way to closely allign my front end. i dont want to go to a shop until i get new wheels on.but i want to be able to drive it on test drives while im working on it. p.s. its a 76 suspension and im putting in new tie rods.

12-08-2010, 09:14 PM	#2
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,546	Re: alignment ?s Unless ur current tires are bad, I would align it, if you take it to Firestone, you can get a 1 time align or a lifetime align, might be worth it if your roads are bad where you live. __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

12-08-2010, 09:35 PM	#3
TR65 Senior Member Join Date: Nov 2007 Location: Greenville, SC Posts: 873	Re: alignment ?s CB, Check out this thread. http://67-72chevytrucks.com/vboard/s...ight=alignment and this one http://67-72chevytrucks.com/vboard/s...ight=alignment TR __________________ 1965 C10 SWB Fleet Two owner LS2 Swap Thread http://67-72chevytrucks.com/vboard/s...d.php?t=413880

12-08-2010, 11:23 PM	#4
ChopperDr Registered User Join Date: Feb 2008 Location: WA Posts: 189	Re: alignment ?s I'm assuming the '76 suspension has discs. Here's how I do it: Pull the wheels off and support the a-arms at ride height. Pull a string along the rotor face. The strings can be pulled out in front of the truck so you cam measure between them to set toe. Eyeball the camber and don't worry too much about caster. This method will get it drivable. Its fun to see how close you can get them with this method. Chop

12-08-2010, 11:44 PM	#5
bama63 Registered User Join Date: Jun 2010 Location: gadsden, alabama Posts: 468	Re: alignment ?s remove the dust cap and use a torpedo level to set the camber and use a tape measure and a friend to measure the toe __________________ Due to financial constraints, the light at the end of the tunnel will be shut off until further notice



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.