|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-10-2010, 08:12 PM
|
#1 |
|
Broken Down
Join Date: Dec 2006
Location: Choctaw, Oklahoma
Posts: 1,267
|
Neutral Safety Switch Location
Ok, hopefully I'm not loosing my mind. I can not find my Neutral saftey switch. I have a 82 chevy K10 auto tranny. I looked inside on the steering column down towards the firewall where it bolts to the firewall. There is a cut out or opening in the column where it looks to go but I don't see it anywhere. The engine will not start in gear so it acts like it has one but I can't find it. Is it located somewhere else?
__________________
kenm78 1982 Chevy 4X4 Project truck  “It’s better to keep your mouth shut and let people wonder about your ignorance, than open your mouth and reveal all doubt” |
|
|
|
12-10-2010, 08:24 PM
|
#2 |
|
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: Neutral Safety Switch Location
it could also be on the ignition switch its on top of the column close to the dash
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 |
|
|
|
|
12-10-2010, 09:14 PM
|
#3 |
|
Broken Down
Join Date: Dec 2006
Location: Choctaw, Oklahoma
Posts: 1,267
|
Re: Neutral Safety Switch Location
Anyone have a picture of this style of switch mentioned?
__________________
kenm78 1982 Chevy 4X4 Project truck “It’s better to keep your mouth shut and let people wonder about your ignorance, than open your mouth and reveal all doubt” |
|
|
|
|
12-11-2010, 12:07 PM
|
#4 |
|
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: Neutral Safety Switch Location
here what the switch looks like
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 |
|
|
|
|
12-11-2010, 01:42 PM
|
#5 | |
|
Broken Down
Join Date: Dec 2006
Location: Choctaw, Oklahoma
Posts: 1,267
|
Re: Neutral Safety Switch Location
Quote:
No picture attached
__________________
kenm78 1982 Chevy 4X4 Project truck “It’s better to keep your mouth shut and let people wonder about your ignorance, than open your mouth and reveal all doubt” |
|
|
|
|
|
12-11-2010, 02:28 PM
|
#6 |
|
Next!
Join Date: Jan 2003
Location: Eastern Pa.
Posts: 2,483
|
Re: Neutral Safety Switch Location
this is what one looks like for an 84 85 86
__________________
86 K30 CUCV M1028A1 86 K30 CUCV M1028a2 dually 86 K30 C&C 6.2 4:56s, 4M, 11,000 gvw, ex fire truck, now lowboy dump More square bodies and CUCVs than I care to admit to 2020 Silverado K3500HD Work truck |
|
|
|
|
12-11-2010, 03:51 PM
|
#7 | |
|
Broken Down
Join Date: Dec 2006
Location: Choctaw, Oklahoma
Posts: 1,267
|
Re: Neutral Safety Switch Location
Quote:
The end of the story is I wanted to get my back up lights working and couldn't find the neutral saftey switch. Everything I have seen or read indicates the back up light switch was intergrated in the neutral saftey switch. The switch I found looks just like a neutral saftey switch but only has two electrical prongs on it. It fits in my column and works great. The only thing I had to do was ziptie it in place becouse my column has clips that require it to be screwed in and this switch didn't have any moldings to fasten it down. Now I have backup lights! Thanks for pointing me towards the ignition switch becouse thats where the backup light harness was wrapped up hiding from me.
__________________
kenm78 1982 Chevy 4X4 Project truck “It’s better to keep your mouth shut and let people wonder about your ignorance, than open your mouth and reveal all doubt” |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
