Delco radio with aux. input added - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Cramitthefrog · 02-16-2011, 11:50 PM

This topic is an FAQ-"73-87 Delco radio with aux. input added"

Hello all. This mod came about because I wanted to listen to my ipod in my truck, but I did not want to cut my dash. I looked into the aftermarket shaft style but right now I can't justify the cost, so for about $20 I made my own.
If all this is a repost my apologies up front.

The first thing I did was grab a stock radio from the local yard, and started to locate what wires were the tuner wires before the amp. This part is real easy, there is a ORANGE wire and GREEN wire that go from the main board to the amp board

What you need to do now is cut the wires in the middle so you don't need to solder directly onto the board. Now if you look at the location of the wires on the amp board it will tell you which one is left and right

Next you need to get a switchable female aux. input. I found one at radio shack, and it is real easy to locate because it will have 5 posts and has a clear side so you can see inside to id which is in and out for both the left and the right channels. The reason you need a switchable input is because without something plugged in you have normal radio function, but as soon as you plug your ipod in it will disconnect the radio function and will send the new source into the amp

So now that you have cut the wires you need to solder 5 wires onto the aux. input. 1 ground that goes to the radio body , a right channel in and out, and a left channel in and out

Now you need to find out which is the left and right channels on the male portion that you plug in. If you look at the plug you will see 3 sections, the first at the tip is the left channel, the next one is the right channel, and the third is the ground. You need to solder the the red and green wires from the main board to the input posts on the aux. input then solder the output wires of the aux. input to the wires going into the amp board.
Once that is done you need to drill a small hole for the input to mount into, I found that just above the first channel select was about the best spot. This will involve cutting the am/fm selector plate to clear the wires. After all that it is time to put the radio case back together

One thing you need to be careful of is to have the radio off when you plug in and unplug your ipod because for a brief instance everything will be connected and the possibility of damaging something is higher.

With all things electrical take your time and double check all conections before you solder, I learned this the hard way and burnt up a perfectly good radio. I also used an am/fm only radio because you have more room to work, but I am sure one with a cassette would work also.
I am sure I confused some people with all of the input here and output there but if you shoot me a pm I could try and help. I just realized that this should be in the audio section, sorry about that. Could a mod please move it. Dang newbies

Telecasterjoey · 02-16-2011, 11:53 PM

Man!! I've been wanting to do this forever! how does it sound??

Cramitthefrog · 02-16-2011, 11:55 PM

It sounds good, but it probably couldn't hang with a new aftermarket head unit.

f.monroe · 02-16-2011, 11:57 PM

Super Cool mod and thanks for sharing.
Frank

Telecasterjoey · 02-17-2011, 12:02 AM

I'll definitely be messaging you with some questions lol i'm gonna do it soon.

Cramitthefrog · 02-17-2011, 12:05 AM

No problem. If you need different pics let me know.

Telecasterjoey · 02-17-2011, 12:10 AM

lemme see if I get it, You're just finding the right and left inputs going from the tuner to the amp and you're putting the input between them? Do you have a pic of the input you bought, and also just a close up of the cut wires?

Thanks so much, so glad someone figured out how to do this!!

Cramitthefrog · 02-17-2011, 12:55 AM

I don't have a pic of the input but I can swing into radio shack and get a part number.
You've got it the input goes directly in between the tuner and amp.
This is my first time posting something like this so next time I will grab the camera sooner.

Telecasterjoey · 02-17-2011, 01:06 AM

Excellent! I think I'll be able to pull it off lol just gotta find the right input at radio shack.
Thanks a lot man!

Cramitthefrog · 02-17-2011, 01:16 AM

more pics I hope this helps

I made a mistake in the first post, it is the ORANGE and green

Pop's C-10 · 02-17-2011, 03:54 AM

This is tha mod i been looking for info on for awhile..thanks for tha info fam..

ElGracho · 02-17-2011, 10:17 AM

Very cool. This needs to be a sticky...

spudz · 02-17-2011, 11:13 AM

THANK YOU SO MUCH FOR SHARING!!!... I will be using this mod for sure as I like the look of stock.

Pop's C-10 · 02-17-2011, 11:22 AM

Quote:

Originally Posted by ElGracho

Very cool. This needs to be a sticky...

I agree

**N2TRUX** · 02-17-2011, 11:35 AM

Quote:

Originally Posted by ElGracho

Very cool. This needs to be a sticky...

Better than a sticky, I plan to make it an FAQ. I will get to it later today.

Telecasterjoey · 02-17-2011, 04:07 PM

Hey man, My radio's guts look a little different! Maybe you can point me in the right direction. My wires appear to be orange yellow and blue, which would I cut? also I've been all over town today looking for the female switchable aux input and no one has any. I know radio shack sells stuff online so I may have to do that.

Pop's C-10 · 02-17-2011, 04:37 PM

Quote:

Originally Posted by N2TRUX

Better than a sticky, I plan to make it an FAQ. I will get to it later today.

Thank u sir...

**N2TRUX** · 02-17-2011, 04:46 PM

My pleasure...
Posted via Mobile Device

Cramitthefrog · 02-17-2011, 05:51 PM

Quote:

Originally Posted by Telecasterjoey

Hey man, My radio's guts look a little different! Maybe you can point me in the right direction. My wires appear to be orange yellow and blue, which would I cut? also I've been all over town today looking for the female switchable aux input and no one has any. I know radio shack sells stuff online so I may have to do that.

What year is your radio?
There will only be 2 wires that carry the audio signal one for left one for right.
Do the orange, yellow and blue go from the main board (the bottom board)
to the amp board?
Take some pics of both boards so I can whats going where.
And last if you can't find the aux input let me know I will pick one up and mail it to you.

I looked at your pics again and it looks like the orange, yellow, and blue wires are coming from the pot for the tuner controls. Thats not the ones you need.

Cramitthefrog · 02-17-2011, 06:45 PM

I went down to radio shack and picked up another input, so hopefully this will help.

Part number 274-0246 1/8 Stereo Phone Jack

http://67-72chevytrucks.com/vboard/a...1&d=1297982693

WigglesTheHoly · 02-17-2011, 06:57 PM

YES!!!! This is something I've been meaning to do as well but never got around to it. I think I may just bypass the radio completely I really don't listen to the radio. I'm a podcast listener myself being a tech nerd. Thank you for saving me 150 bucks for an aftermarket post radio.

Cramitthefrog · 02-17-2011, 07:02 PM

My pleasure, I am glad people find it useful.

Telecasterjoey · 02-17-2011, 08:28 PM

I think the radio is a 1980? I took it out of a screwed up truck from the scrap yard. I have an 86 tape player stock radio, and I've located the green and orange wires. My radio is different but I think I can figure it out. Would you mind selling me the part? I think Im going to have a hard time tracking it down. Radio shack doesn't ship to canada

again thanks so much for your help!!!

Pop's C-10 · 02-17-2011, 08:43 PM

Quote:

Originally Posted by WigglesTheHoly

YES!!!! This is something I've been meaning to do as well but never got around to it. I think I may just bypass the radio completely I really don't listen to the radio. I'm a podcast listener myself being a tech nerd. Thank you for saving me 150 bucks for an aftermarket post radio.

Are you talking about jus wiring tha aux input right to you speakers?..not that would be trick..

spudz · 02-17-2011, 09:07 PM

do you see any problem doing this to a newer digital display head unit?

02-16-2011, 11:50 PM	#1
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Delco radio with aux. input added This topic is an FAQ-"73-87 Delco radio with aux. input added" Hello all. This mod came about because I wanted to listen to my ipod in my truck, but I did not want to cut my dash. I looked into the aftermarket shaft style but right now I can't justify the cost, so for about $20 I made my own. If all this is a repost my apologies up front. The first thing I did was grab a stock radio from the local yard, and started to locate what wires were the tuner wires before the amp. This part is real easy, there is a ORANGE wire and GREEN wire that go from the main board to the amp board What you need to do now is cut the wires in the middle so you don't need to solder directly onto the board. Now if you look at the location of the wires on the amp board it will tell you which one is left and right Next you need to get a switchable female aux. input. I found one at radio shack, and it is real easy to locate because it will have 5 posts and has a clear side so you can see inside to id which is in and out for both the left and the right channels. The reason you need a switchable input is because without something plugged in you have normal radio function, but as soon as you plug your ipod in it will disconnect the radio function and will send the new source into the amp So now that you have cut the wires you need to solder 5 wires onto the aux. input. 1 ground that goes to the radio body , a right channel in and out, and a left channel in and out Now you need to find out which is the left and right channels on the male portion that you plug in. If you look at the plug you will see 3 sections, the first at the tip is the left channel, the next one is the right channel, and the third is the ground. You need to solder the the red and green wires from the main board to the input posts on the aux. input then solder the output wires of the aux. input to the wires going into the amp board. Once that is done you need to drill a small hole for the input to mount into, I found that just above the first channel select was about the best spot. This will involve cutting the am/fm selector plate to clear the wires. After all that it is time to put the radio case back together One thing you need to be careful of is to have the radio off when you plug in and unplug your ipod because for a brief instance everything will be connected and the possibility of damaging something is higher. With all things electrical take your time and double check all conections before you solder, I learned this the hard way and burnt up a perfectly good radio. I also used an am/fm only radio because you have more room to work, but I am sure one with a cassette would work also. I am sure I confused some people with all of the input here and output there but if you shoot me a pm I could try and help. I just realized that this should be in the audio section, sorry about that. Could a mod please move it. Dang newbies Attached Images Last edited by N2TRUX; 11-17-2011 at 11:59 PM.

02-16-2011, 11:53 PM	#2
Telecasterjoey Registered User Join Date: Nov 2010 Location: Ottawa ON Posts: 514	Re: Delco radio with aux. input added Man!! I've been wanting to do this forever! how does it sound??

02-16-2011, 11:55 PM	#3
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: Delco radio with aux. input added It sounds good, but it probably couldn't hang with a new aftermarket head unit.

02-16-2011, 11:57 PM	#4
f.monroe Senior Member Join Date: May 2004 Location: Caldwell,Tx. Posts: 3,648	Re: Delco radio with aux. input added Super Cool mod and thanks for sharing. Frank __________________ Born and proudly residing in a Red State !

02-17-2011, 12:02 AM	#5
Telecasterjoey Registered User Join Date: Nov 2010 Location: Ottawa ON Posts: 514	Re: Delco radio with aux. input added I'll definitely be messaging you with some questions lol i'm gonna do it soon.

02-17-2011, 12:05 AM	#6
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: Delco radio with aux. input added No problem. If you need different pics let me know.

02-17-2011, 12:10 AM	#7
Telecasterjoey Registered User Join Date: Nov 2010 Location: Ottawa ON Posts: 514	Re: Delco radio with aux. input added lemme see if I get it, You're just finding the right and left inputs going from the tuner to the amp and you're putting the input between them? Do you have a pic of the input you bought, and also just a close up of the cut wires? Thanks so much, so glad someone figured out how to do this!!

02-17-2011, 12:55 AM	#8
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: Delco radio with aux. input added I don't have a pic of the input but I can swing into radio shack and get a part number. You've got it the input goes directly in between the tuner and amp. This is my first time posting something like this so next time I will grab the camera sooner.

02-17-2011, 01:06 AM	#9
Telecasterjoey Registered User Join Date: Nov 2010 Location: Ottawa ON Posts: 514	Re: Delco radio with aux. input added Excellent! I think I'll be able to pull it off lol just gotta find the right input at radio shack. Thanks a lot man!

02-17-2011, 01:16 AM	#10
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: Delco radio with aux. input added more pics I hope this helps I made a mistake in the first post, it is the ORANGE and green Attached Images Last edited by N2TRUX; 02-17-2011 at 11:38 AM.

02-17-2011, 03:54 AM	#11
Pop's C-10 Registered User Join Date: Jul 2010 Location: memphis Posts: 2,537	Re: Delco radio with aux. input added This is tha mod i been looking for info on for awhile..thanks for tha info fam..

02-17-2011, 10:17 AM	#12
ElGracho Gentleman Jim Driver Join Date: Nov 2002 Location: Poulsbo, WA Posts: 1,553	Re: Delco radio with aux. input added Very cool. This needs to be a sticky... __________________ Joe '75 GMC Gentleman Jim '84 Chev C10 Short Wide - Super duper plain (manual steering, manual brakes, no dome light, no cig lighter) '85 Chev C10 Short Wide - Super plain Vortec 4.8 4L60E trans also: '81 K30, '83 C30 Crew Dually, '84 M1028 CUCV, '85 M1009 CUCV, another '85 C10 SWB, '89 R3500 Flatbed

02-17-2011, 11:13 AM	#13
spudz Registered User Join Date: Oct 2005 Location: Branchville SC Posts: 1,647	Re: Delco radio with aux. input added THANK YOU SO MUCH FOR SHARING!!!... I will be using this mod for sure as I like the look of stock. __________________ 2004 z71, 96 z71 on 38s, 88 Chevy k5 blazer, 4in lift. 84 swb project, 82 SWB project , 84 chevy 4x4 lwb project, 88 Jimmy beater/highschool ride. 79 c30. 99 tahoe 4x4 project. and a bunch of parts trucks..

02-17-2011, 04:07 PM	#16
Telecasterjoey Registered User Join Date: Nov 2010 Location: Ottawa ON Posts: 514	Re: Delco radio with aux. input added Hey man, My radio's guts look a little different! Maybe you can point me in the right direction. My wires appear to be orange yellow and blue, which would I cut? also I've been all over town today looking for the female switchable aux input and no one has any. I know radio shack sells stuff online so I may have to do that. Attached Images

02-17-2011, 04:46 PM	#18
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: Delco radio with aux. input added My pleasure... Posted via Mobile Device



Register or Log In To remove these advertisements.

02-17-2011, 06:45 PM	#20
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: Delco radio with aux. input added I went down to radio shack and picked up another input, so hopefully this will help. Part number 274-0246 1/8 Stereo Phone Jack http://67-72chevytrucks.com/vboard/a...1&d=1297982693 Attached Images

02-17-2011, 06:57 PM	#21
WigglesTheHoly IT Guy/ Father/ Chevy lover Join Date: Feb 2010 Location: Hoisington, KS Posts: 568	Re: Delco radio with aux. input added YES!!!! This is something I've been meaning to do as well but never got around to it. I think I may just bypass the radio completely I really don't listen to the radio. I'm a podcast listener myself being a tech nerd. Thank you for saving me 150 bucks for an aftermarket post radio. __________________ 78 Chevy (Pictures) SOLD 79 Chevy LWB (pasture) 83 Chevy LWB (crushed rusted beyond repair) 02 TrailBlazer SOLD 03 VW Passat wagonSOLD 95 extended cab silveradoSOLD (still in family) 05 Crew Cab Silverado 5.3 (The Turd) WTB: 66 El camino Technology Specialist aspiring to be a gear head.

02-17-2011, 07:02 PM	#22
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: Delco radio with aux. input added My pleasure, I am glad people find it useful.

02-17-2011, 08:28 PM	#23
Telecasterjoey Registered User Join Date: Nov 2010 Location: Ottawa ON Posts: 514	Re: Delco radio with aux. input added I think the radio is a 1980? I took it out of a screwed up truck from the scrap yard. I have an 86 tape player stock radio, and I've located the green and orange wires. My radio is different but I think I can figure it out. Would you mind selling me the part? I think Im going to have a hard time tracking it down. Radio shack doesn't ship to canada again thanks so much for your help!!! Last edited by Telecasterjoey; 02-17-2011 at 08:30 PM.

02-17-2011, 09:07 PM	#25
spudz Registered User Join Date: Oct 2005 Location: Branchville SC Posts: 1,647	Re: Delco radio with aux. input added do you see any problem doing this to a newer digital display head unit? __________________ 2004 z71, 96 z71 on 38s, 88 Chevy k5 blazer, 4in lift. 84 swb project, 82 SWB project , 84 chevy 4x4 lwb project, 88 Jimmy beater/highschool ride. 79 c30. 99 tahoe 4x4 project. and a bunch of parts trucks..

Register or Log In To remove these advertisements.