What did you do to your truck this week? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bluex · 08-01-2011, 09:34 PM

Camshaftgsxr here is your thread!

I havent touched mine. I pulled it out of the garage and put it back in, thats it for this week.....

CaliDude76 · 08-01-2011, 09:51 PM

I got bugz on the windshield and grille this week

camshaftgsxr · 08-02-2011, 12:19 AM

Haha, I love this forum.

nothing yet, began planning for nitrous tho...
Posted via Mobile Device

TrucknAndy · 08-02-2011, 01:04 AM

Ive been undoing a PO's "not so handy work." Apparently, either the expense, or the lack of common sense eluded this fella. He stuffed the guts from god knows what into the drums, and to ice the cake put two different drums on the rear. Same max. diameter, but still different, and still not stock to my truck.

So, 2 drums, new shoes, hardware kit, adjuster kit, one new brake line section, and hunting down the correct parking brake lever I am almost done. Last of the parts should be in tomorrow and should have her back on the road.

I was nervous as it was my first time doing drum brakes. Someone made it a total nightmare for me, but I am now very informed on drum brakes. Hope this is the last time I uncover this genious' inability to do it right the first time.

Andy

juiceman650 · 08-02-2011, 02:40 AM

Fixed my oil pressure line, put fresh spark plug wires in, got the correct firing order down, drove it to work a couple days, sat in the driveway under its cover, waiting for Wednesday to swap the fuel pump.
Posted via Mobile Device

bigsj · 08-02-2011, 07:52 AM

Cleaned the engine bay.

75ChevyGuy · 08-02-2011, 11:14 AM

Retightened my headers, and did a full tune up.

TIM86 · 08-02-2011, 11:34 AM

Put on my sport bumper. Now Im looking at it trying to figure out how to straighten it out.

88bagedntaged · 08-02-2011, 11:36 AM

Took a 1993 Short Bed to be lowered !!

81Psychobilly · 08-02-2011, 11:44 AM

Slow trying to get mine back together.......

[IMG]

[/IMG]

BigRed91 · 08-02-2011, 01:53 PM

New bearings, rotors, and pads on the front and fixed some of the electrical.

veinbar · 08-02-2011, 02:37 PM

Resolved many of my electrical issues.

Fuel Gauge works!
Dash Lights work!
Cigarette Lighter/Phone Charger works!
Aftermarket Gauge Lights work!
Dome Light works!

Also, I went and pulled a 700r4 out of my '76 Chevy Van which will be going into my '79 Bonanza.

thesickc10 · 08-02-2011, 03:31 PM

got some new shoes. american racing torque thrust 2's 15x8 wrapped in 275/60/15 dunlops. bad picture they actually look good trust me haha. its begging to sit lower now!

shaggy4267 · 08-02-2011, 06:10 PM

Picked up a cart with casters, perfect for rolling around the cab and box I'm working on. Bought a D/A, sandpaper, epoxy primer, sand for the blaster, and some other odds & ends. Cleaned the garage up a bit.

bluex · 08-03-2011, 01:41 AM

Quote:

Originally Posted by camshaftgsxr

Haha, I love this forum.

nothing yet, began planning for nitrous tho...
Posted via Mobile Device

Your welcome...

Posted via Mobile Device

baclay9 · 08-03-2011, 01:52 AM

Got my new rallies painted and mounted up with new rubber.

By claypool782 at 2011-08-01

tashspop · 08-03-2011, 08:03 AM

i'm fighting with an old carb until i get to buy a new one. scavanged an electric choke off of one and put it on mine. still adjusting it out.

camshaftgsxr · 08-03-2011, 12:38 PM

picked up new (used) side glass last night in hopes of having windows that roll down AND back up

motornut · 08-03-2011, 10:27 PM

Jimmy/blazers are rare around here so when somebody tells me about a jimmy 77 being sold with property,a garage,i gotta go see
about 1.5 hours east of me......drove there oh it's at home now
(me thunks if it moves how bad can it be)whats another 1/2 hour
i shoulda ran away when i saw a filler neck stickin out the back window
don't think i should repost the pics so
link the jimmy sig below..........post 110

grs · 08-04-2011, 05:03 PM

I am on vacation in Texas, so I thought about my truck.

veinbar · 08-04-2011, 05:23 PM

When I get off of work, I'm going straight home to empty my truck bed out. It's overflowing with Tools and truck parts. I need it empty so I can fill it up again this weekend. Somehow I need to transport a sbc 350, a th350, gm 10 bolt rear, steel wheel set of 4, and a driveshaft. Can a stock 1/2 ton handle that weight?

ScottW · 08-04-2011, 05:42 PM

Got the doors, fenders and hood ready for paint.

CaliDude76 · 08-04-2011, 08:52 PM

[QUOTE=baclay9;4825196]Got my new rallies painted and mounted up with new rubber.

By claypool782 at 2011-08-01

Where did you get those spinner caps?? Been trying to locate where I can get some.

Thanks,
-CaliDude

Dan1969 · 08-04-2011, 10:20 PM

Quote:

Originally Posted by 81Psychobilly

Slow trying to get mine back together.......

[IMG]

[/IMG]

What pieces did you use to rebuild this floor?

camshaftgsxr · 08-04-2011, 10:51 PM

I took a Drive sipping a vanilla coke with the windows down after a long time of them jammed to the top of the tracks! Feelsgoodman
Posted via Mobile Device

08-01-2011, 09:34 PM	#1
bluex Registered User Join Date: Jun 2004 Location: Spartanburg, SC Posts: 1,963	What did you do to your truck this week? Camshaftgsxr here is your thread! I havent touched mine. I pulled it out of the garage and put it back in, thats it for this week..... __________________ Paul '78 GMC Serria 15 Heavy Half. 361/NV3500/3.73. Former LWB NV3500 swap Trailing arm swap '98 ECSB Z71 daily driver -traded '03 burb. Family cruiser http://upstategmtrucks.com/

08-01-2011, 09:51 PM	#2
CaliDude76 All About the BOWTIE Join Date: May 2010 Location: Los Banos, California Posts: 436	Re: What did you do to your truck this week? I got bugz on the windshield and grille this week __________________ CaliDude76 "... Being "SQUARE".. is where it's at...." Proverbs 15:30 .... "A Cheerful look brings joy to the heart, and good news gives health to the bones..." Be exceedingly blessed today, my friends!...

08-02-2011, 12:19 AM	#3
camshaftgsxr Registered User Join Date: Feb 2010 Location: Asheville, N.C. Posts: 785	Re: What did you do to your truck this week? Haha, I love this forum. nothing yet, began planning for nitrous tho... Posted via Mobile Device __________________

08-02-2011, 01:04 AM	#4
TrucknAndy Registered User Join Date: Jun 2011 Location: Wichita Falls, Tx Posts: 69	Re: What did you do to your truck this week? Ive been undoing a PO's "not so handy work." Apparently, either the expense, or the lack of common sense eluded this fella. He stuffed the guts from god knows what into the drums, and to ice the cake put two different drums on the rear. Same max. diameter, but still different, and still not stock to my truck. So, 2 drums, new shoes, hardware kit, adjuster kit, one new brake line section, and hunting down the correct parking brake lever I am almost done. Last of the parts should be in tomorrow and should have her back on the road. I was nervous as it was my first time doing drum brakes. Someone made it a total nightmare for me, but I am now very informed on drum brakes. Hope this is the last time I uncover this genious' inability to do it right the first time. Andy

08-02-2011, 02:40 AM	#5
juiceman650 Registered User Join Date: Jan 2011 Location: San Bruno, CA. Posts: 348	Re: What did you do to your truck this week? Fixed my oil pressure line, put fresh spark plug wires in, got the correct firing order down, drove it to work a couple days, sat in the driveway under its cover, waiting for Wednesday to swap the fuel pump. Posted via Mobile Device

08-02-2011, 07:52 AM	#6
bigsj Registered User Join Date: Mar 2011 Location: Bowie Maryland Posts: 335	Re: What did you do to your truck this week? Cleaned the engine bay.

08-02-2011, 11:14 AM	#7
75ChevyGuy GM Parts Guy Join Date: Jan 2011 Location: Attleboro MA Posts: 375	Re: What did you do to your truck this week? Retightened my headers, and did a full tune up. __________________ 1975 Chevrolet C-10 Custom Deluxe (DD/WIP) 1989 Chevrolet C1500 reg cab stepside (Winter Truck) 1977 Harley Davidson XLH 1000 (Summer Cruiser)

08-02-2011, 11:34 AM	#8
TIM86 Registered User Join Date: May 2011 Location: St.Petersburg,FL Posts: 158	Re: What did you do to your truck this week? Put on my sport bumper. Now Im looking at it trying to figure out how to straighten it out.

08-02-2011, 11:36 AM	#9
88bagedntaged Registered User Join Date: Jan 2010 Location: Dallas Tx Posts: 172	Re: What did you do to your truck this week? Took a 1993 Short Bed to be lowered !! Attached Images

08-02-2011, 11:44 AM	#10
81Psychobilly Registered User Join Date: Jun 2011 Location: Aspers, PA Posts: 18	Re: What did you do to your truck this week? Slow trying to get mine back together....... [IMG][/IMG]

08-02-2011, 01:53 PM	#11
BigRed91 Registered User Join Date: Aug 2010 Location: Ottawa, Kansas Posts: 25	Re: What did you do to your truck this week? New bearings, rotors, and pads on the front and fixed some of the electrical.

08-02-2011, 02:37 PM	#12
veinbar Registered User Join Date: Mar 2007 Location: Austin, TX Posts: 292	Re: What did you do to your truck this week? Resolved many of my electrical issues. Fuel Gauge works! Dash Lights work! Cigarette Lighter/Phone Charger works! Aftermarket Gauge Lights work! Dome Light works! Also, I went and pulled a 700r4 out of my '76 Chevy Van which will be going into my '79 Bonanza.

08-02-2011, 03:31 PM	#13
thesickc10 Registered User Join Date: Sep 2010 Location: New Hope, PA Posts: 279	Re: What did you do to your truck this week? got some new shoes. american racing torque thrust 2's 15x8 wrapped in 275/60/15 dunlops. bad picture they actually look good trust me haha. its begging to sit lower now! __________________ 1985 c10 355 th350 (working on 4 speed conversion to super t10) 1979 camaro 358 super t10 2003 f250 superchip slp exhaust

08-02-2011, 06:10 PM	#14
shaggy4267 Registered User Join Date: May 2011 Location: MI Posts: 11	Re: What did you do to your truck this week? Picked up a cart with casters, perfect for rolling around the cab and box I'm working on. Bought a D/A, sandpaper, epoxy primer, sand for the blaster, and some other odds & ends. Cleaned the garage up a bit.

08-03-2011, 01:52 AM	#16
baclay9 Registered User Join Date: Apr 2010 Location: Newcastle, OK Posts: 1,344	Re: What did you do to your truck this week? Got my new rallies painted and mounted up with new rubber. By claypool782 at 2011-08-01 By claypool782 at 2011-08-01



Register or Log In To remove these advertisements.

08-03-2011, 08:03 AM	#17
tashspop Registered User Join Date: May 2011 Location: houston tx Posts: 21	Re: What did you do to your truck this week? i'm fighting with an old carb until i get to buy a new one. scavanged an electric choke off of one and put it on mine. still adjusting it out.

08-03-2011, 12:38 PM	#18
camshaftgsxr Registered User Join Date: Feb 2010 Location: Asheville, N.C. Posts: 785	Re: What did you do to your truck this week? picked up new (used) side glass last night in hopes of having windows that roll down AND back up __________________

08-03-2011, 10:27 PM	#19
motornut 78K & 79C Jimmys Join Date: Nov 2009 Location: Ottawa Ont CANADA Posts: 7,901	Re: What did you do to your truck this week? Jimmy/blazers are rare around here so when somebody tells me about a jimmy 77 being sold with property,a garage,i gotta go see about 1.5 hours east of me......drove there oh it's at home now (me thunks if it moves how bad can it be)whats another 1/2 hour i shoulda ran away when i saw a filler neck stickin out the back window don't think i should repost the pics so link the jimmy sig below..........post 110 __________________ John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350

08-04-2011, 05:03 PM	#20
grs Registered User Join Date: Jan 2010 Location: Roanoke, Tx. Posts: 1,561	Re: What did you do to your truck this week? I am on vacation in Texas, so I thought about my truck.

08-04-2011, 05:23 PM	#21
veinbar Registered User Join Date: Mar 2007 Location: Austin, TX Posts: 292	Re: What did you do to your truck this week? When I get off of work, I'm going straight home to empty my truck bed out. It's overflowing with Tools and truck parts. I need it empty so I can fill it up again this weekend. Somehow I need to transport a sbc 350, a th350, gm 10 bolt rear, steel wheel set of 4, and a driveshaft. Can a stock 1/2 ton handle that weight? __________________ 2008 Yamaha Zuma 50cc - Daily Driver 1979 Chevrolet Bonanza SWB; 357ci, TH400, 3.73 Posi - Daily Driver 1976 Chevrolet Sport Van SWB; 355ci, TH350, 2.73 Open - Rape Free 1972 Oldsmobile Cutlass S; 455ci, TH400, 2.73 Open - SOLD (but I still claim to own it from time to time)

08-04-2011, 05:42 PM	#22
ScottW Registered User Join Date: Mar 2010 Location: Indian Trail, NC Posts: 13	Re: What did you do to your truck this week? Got the doors, fenders and hood ready for paint.

08-04-2011, 08:52 PM	#23
CaliDude76 All About the BOWTIE Join Date: May 2010 Location: Los Banos, California Posts: 436	Re: What did you do to your truck this week? [QUOTE=baclay9;4825196]Got my new rallies painted and mounted up with new rubber. By claypool782 at 2011-08-01 Where did you get those spinner caps?? Been trying to locate where I can get some. Thanks, -CaliDude __________________ CaliDude76 "... Being "SQUARE".. is where it's at...." Proverbs 15:30 .... "A Cheerful look brings joy to the heart, and good news gives health to the bones..." Be exceedingly blessed today, my friends!...

08-04-2011, 10:51 PM	#25
camshaftgsxr Registered User Join Date: Feb 2010 Location: Asheville, N.C. Posts: 785	Re: What did you do to your truck this week? I took a Drive sipping a vanilla coke with the windows down after a long time of them jammed to the top of the tracks! Feelsgoodman Posted via Mobile Device __________________

Register or Log In To remove these advertisements.