Gas pedal mods

[61_FL_Apache]

After installing the kickdown cable bracket, my stock gas pedal lever on the engine side of the firewall is not working as freely as it should.

Has anyone installed a later model gas pedel assembly from a 70's or 80's pickup?

If you have pics to show that would be great.

This is something I had in mind.

http://www.ebay.com/itm/85-86-87-CHE...item2c61bfa291

[markeb01]

Don't have any input to offer regarding the later pedal assembly, but it sounds like you may have a problem with the kickdown cable install. I used a standard (cheap) version of the Chevy 350 Lokar kickdown cable and bracket and it worked perfectly for 15 years with the stock gas pedal linkage, until I pulled the cable when I swapped back to a stick shift transmission.

http://www.lokar.com/product-pgs/thr...s/th350kd.html

[Fastrucken]

I used the gas pedal from an 87 suburban for my 5.3 swap. I just looked and don’t have any pics of the install (truck stored for the winter) but it wasn’t hard. I bolted it onto place, then drilled a hole for the cable. I also remember using a small file to square up the hole to better fit the cable to the firewall.

I also remember buying a pedal from a 70-72 truck but preferred the later style. I think it had something to do with the way the pedal is bent. I do remember both would have worked though

Graham

[Rich 5150 69]

Can you tell us what was in there before that...it may be just an alignment issue!

[61_FL_Apache]

It appears to be the stock pedal and lever assembly. I will take and post pics tonight when I get home.

[flips72]

i put a 72 pedal assemby in mine, the rough firewall is where i made room for my tall valve covers, the square hole i made by drilling a 1/2 hole and used a small flat file to make the corners, hope this helps.

[61_FL_Apache]

Thanks Flip! Thats what im looking to do.

Here is a pic from the inside.


Here are a few from the engine side.





You can see the interference I am getting between the kickdown cable bracket and the throttle linkage. It works, but I would like it to work better.

Currently the lever between the rod connected the carb and the firewall moves up and back when pressing the pedal. It hits the spark plug wires and other dist wires. Im looking for a setup like the later models that use a cable and pulls straight back.

Thanks again for the input!!

[doobiebro]

Originally Posted by 61_FL_Apache

Thanks Flip! Thats what im looking to do.

Here is a pic from the inside.


Here are a few from the engine side.





You can see the interference I am getting between the kickdown cable bracket and the throttle linkage. It works, but I would like it to work better.

Currently the lever between the rod connected the carb and the firewall moves up and back when pressing the pedal. It hits the spark plug wires and other dist wires. Im looking for a setup like the later models that use a cable and pulls straight back.

Thanks again for the input!!

Depending on the carb and transmission application you got... you can get a kickdown cable mounting bracket that bolts under the carb and you wont have clearance issues....heres a pic....just a suggestion... Also a cheap fix just make the throttle lever longer like my pic. My lever is actually original for v-8 application thanks to a member. just fab yours...

[Clownpuncher]

If not can't you just adjust lengthen the rod and move the rod back some? I had this setup on my Nova and it worked out wel.. I even had the cables ran behind the rod and never had an issue. There really isn't alot of travel needed for that lever.

Or you can have a rod that sits flat then at the last 2" bend it down then back again. This would keep your lever more vertical instead of a 45 it's at now

I cable option will fix it I'm just saying you can make something work with your current setup.

[1Bad62Pro/Street]

Lokar ''Eliminator'' Floor Mounted Gas Pedal

http://www.jegs.com/p/Lokar/Lokar-El...50221/10002/-1
Posted via Mobile Device
Posted via Mobile Device

[61_FL_Apache]

I like the Lokar option too, but I need a low buck fix for now.

[Clyde65]

I used the Locar option, it works but I would like something a little less bling and more stock looking, I know, I know, Picky Sh1t!

[61_FL_Apache]

I would rather have my plug wires routed under the linkage like you have there. If I get the wires lower and the linkage up higher, that will solve my issue.

Thanks for the input.