Dirty Dingo Serp. Belt Routing - The 1947 - Present Chevrolet & GMC Truck Message Board Network

solidaxel · 02-06-2013, 11:55 PM

Can someone please send me a pic of the belt routing on a 2006 5.3 with a raised Dirty Dingo A/C bracket and idler, stock alternator and power steering pump and the part number of the belt, or total inches of belt

solidaxel · 02-09-2013, 09:46 PM

Anybody with a pic of a 5.3 and DD A/C bracket !!!!

69trk · 02-09-2013, 09:53 PM

Might go to dirty dingos' site. If i remember right they have picts.. I'm planning on running a ac bracket from lsbrackets that moves it up and inward so i can fit some forward facing headers..

solidaxel · 02-09-2013, 10:19 PM

You are right but he only shows his bracket and not the rest of the pulleys and acc.

85burb · 02-10-2013, 10:39 AM

From there web page it goes from ac to under water pump. Kinda crappy instructions. From under water pump I have no ideas.
Posted via Mobile Device

gumbys10 · 02-10-2013, 11:34 AM

First picture looks close. Remove the belt from the idler between the altenator and power steering pump, allow it to go straight there, and route the belt under idler pulley between the a/c compressor and altenator and you will have it routed correctly.

solidaxel · 02-10-2013, 12:22 PM

Thanks,
I went back and found the pic you have shown and it is for one of his PS and Alt brackets,
I am only using the DD A/C upper mount bracket, and adj. motor mounts.
I am going to get a hand full of different length belts and re route the belts until everything works.
I think I am the only one to use one of these A/C brackets on this site !!!

gumbys10 · 02-10-2013, 07:18 PM

I have one, I just have not installed it yet lol.

mooseknuckles · 02-10-2013, 07:39 PM

think it goes this way.....cause of the throttle body....

solidaxel · 02-10-2013, 07:48 PM

Thanks,
I am going to measure for a belt the way you have it shown.
That way also clears the water outlet and intake

68GMCCustom · 02-10-2013, 10:45 PM

I have to say...I certainly like that setup better then the kwik one

solidaxel · 02-13-2013, 11:33 PM

Here is the final results after 6 tries, and the same amount of trips to the parts store !!
I think the belt could have been the next 1/2 size smaller, but I think I will ware this one out then see.
Thanks to all for the help and pics,
now on to the sencers and wiring, and fuel lines

02-06-2013, 11:55 PM	#1
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Dirty Dingo Serp. Belt Routing Can someone please send me a pic of the belt routing on a 2006 5.3 with a raised Dirty Dingo A/C bracket and idler, stock alternator and power steering pump and the part number of the belt, or total inches of belt __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

02-09-2013, 09:46 PM	#2
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Dirty Dingo Serp. Belt Routing Anybody with a pic of a 5.3 and DD A/C bracket !!!! Attached Images __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42 Last edited by solidaxel; 02-09-2013 at 09:56 PM.

02-09-2013, 09:53 PM	#3
69trk Registered User Join Date: Oct 2006 Location: bridgecreek ok. Posts: 1,214	Re: Dirty Dingo Serp. Belt Routing Might go to dirty dingos' site. If i remember right they have picts.. I'm planning on running a ac bracket from lsbrackets that moves it up and inward so i can fit some forward facing headers.. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=494388 431 big block times, changed to a 6.0 ls with turbo 1.58- 60' 7.18- 1/8th mile@95.18 11.37- 1/4 @115.81

02-09-2013, 10:19 PM	#4
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Dirty Dingo Serp. Belt Routing You are right but he only shows his bracket and not the rest of the pulleys and acc. __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

02-10-2013, 10:39 AM	#5
85burb Registered User Join Date: Dec 2009 Location: lindale,tx Posts: 2,373	Re: Dirty Dingo Serp. Belt Routing From there web page it goes from ac to under water pump. Kinda crappy instructions. From under water pump I have no ideas. Posted via Mobile Device Attached Images __________________ 82 c10 5.3/4l60 84 c20 5.3/sm465 85 chevy k10 suburban LQ4/4l60 91 chevy c10 suburban Lsa 5.3/4l60 2017 Silverado whipple 5.3 1964 Vw beetle 1974 vw beetle

02-10-2013, 11:34 AM	#6
gumbys10 Registered User Join Date: Aug 2010 Location: Regina Saskatchewan Posts: 213	Re: Dirty Dingo Serp. Belt Routing First picture looks close. Remove the belt from the idler between the altenator and power steering pump, allow it to go straight there, and route the belt under idler pulley between the a/c compressor and altenator and you will have it routed correctly. __________________ http://67-72chevytrucks.com/vboard/s...17#post5397317 http://67-72chevytrucks.com/vboard/s...d.php?t=520480

02-10-2013, 12:22 PM	#7
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Dirty Dingo Serp. Belt Routing Thanks, I went back and found the pic you have shown and it is for one of his PS and Alt brackets, I am only using the DD A/C upper mount bracket, and adj. motor mounts. I am going to get a hand full of different length belts and re route the belts until everything works. I think I am the only one to use one of these A/C brackets on this site !!! __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

02-10-2013, 07:18 PM	#8
gumbys10 Registered User Join Date: Aug 2010 Location: Regina Saskatchewan Posts: 213	Re: Dirty Dingo Serp. Belt Routing I have one, I just have not installed it yet lol. __________________ http://67-72chevytrucks.com/vboard/s...17#post5397317 http://67-72chevytrucks.com/vboard/s...d.php?t=520480

02-10-2013, 07:39 PM	#9
mooseknuckles Registered User Join Date: Sep 2009 Location: ottawa,canada Posts: 4,550	Re: Dirty Dingo Serp. Belt Routing think it goes this way.....cause of the throttle body.... Attached Images __________________ my build threads '86 C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415628 '67 C10 http://67-72chevytrucks.com/vboard/s...d.php?t=635078 '63 GMC http://67-72chevytrucks.com/vboard/s...d.php?t=674682

02-10-2013, 07:48 PM	#10
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Dirty Dingo Serp. Belt Routing Thanks, I am going to measure for a belt the way you have it shown. That way also clears the water outlet and intake __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

02-10-2013, 10:45 PM	#11
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: Dirty Dingo Serp. Belt Routing I have to say...I certainly like that setup better then the kwik one __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

02-13-2013, 11:33 PM	#12
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Dirty Dingo Serp. Belt Routing Here is the final results after 6 tries, and the same amount of trips to the parts store !! I think the belt could have been the next 1/2 size smaller, but I think I will ware this one out then see. Thanks to all for the help and pics, now on to the sencers and wiring, and fuel lines Attached Images __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.