|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-11-2013, 10:51 PM
|
#1 |
|
Registered User
Join Date: Jul 2010
Location: Portland, Oregon
Posts: 411
|
How do i get these apart - Hatch Handle
As you can see or not see from the pics, the retainer pin and ring are gone. What am i missing or do i have too much rust?
 
__________________
Check out my build: 1972 LQ4 Swap http://67-72chevytrucks.com/vboard/s...=1#post5427693 |
|
|
|
02-12-2013, 10:03 AM
|
#2 |
|
Registered User
Join Date: May 2008
Location: 204
Posts: 903
|
Re: How do i get these apart - Hatch Handle
Start soaking it in some penetrating oil.
Posted via Mobile Device
__________________
1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery |
|
|
|
|
02-12-2013, 11:25 AM
|
#3 | |
|
Senior Member
 
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,764
|
Re: How do i get these apart - Hatch Handle
Quote:
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
|
|
|
|
|
02-12-2013, 02:31 PM
|
#4 |
|
Registered User
Join Date: Nov 2007
Location: NLR, AR
Posts: 1,387
|
Re: How do i get these apart - Hatch Handle
#3 what they said.
Then also "lockdoc" made a post about how to take it apart. Read it carefully, I suck at comprehension and screwed one up taking it apart. |
|
|
|
|
02-13-2013, 03:19 AM
|
#5 |
|
Senior Member
Join Date: Aug 2012
Location: Portland, OR
Posts: 939
|
Re: How do i get these apart - Hatch Handle
How did you get that off the hatch? Mine looks just like what you have (well mine has way more rust). I believe once the cotter pin is out of the handle bar it should slide out but mine appears to be rusted solid together. I have tried penetrating oil, hammering the end of the bar and heat and it will not budget. The plate that holds/retains the side levers is wider than the hole that the assembly slides into. Did you remove this from a hatch or get it the way you have it in your photo? I don't understand how you could have got it out of the hatch and not have it disassembled.
Here is mine  Blazer Hatch Handle by Luftwaffepdx, on Flickr I have given up on it and am looking for a replacement - once found, I'm going to cut mine in half so it will come apart. |
|
|
|
|
02-13-2013, 07:39 AM
|
#6 |
|
Registered User
Join Date: Nov 2007
Location: NLR, AR
Posts: 1,387
|
Re: How do i get these apart - Hatch Handle
When it gets to that point. You have to cut it off, and find a new handle. Most people go to a garage door handle, but then its not original.
|
|
|
|
|
02-14-2013, 08:29 AM
|
#7 |
|
Registered User
Join Date: Jul 2010
Location: Portland, Oregon
Posts: 411
|
Re: How do i get these apart - Hatch Handle
PDX - I dont really have an answer. The guy who did the body work got it out. He may have ripped it out and then reglassed it.
__________________
Check out my build: 1972 LQ4 Swap http://67-72chevytrucks.com/vboard/s...=1#post5427693 |
|
|
|
|
02-19-2013, 08:42 PM
|
#8 |
|
The Older Generation
  
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,780
|
Re: How do i get these apart - Hatch Handle
-
I'm not sure how the part with the large spring on it comes off but it looks like it should just slide off of the shaft. Randy (teeitup) should be able to tell you if you PM him. Once you get that off here is the instructions on how to get the rest of it apart... http://67-72chevytrucks.com/vboard/s...d.php?t=503101 LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
