Where to find P/S pulley? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Lumpy · 03-27-2002, 06:04 PM

Hello,
I have a 67 pickup with a 350 in it. The power steering pulley is bent and I would like to replace it. I don't think it is the right one anyways because the pulley on the crank and the pulley on the p/s pump are not lined up right. They are off by maybe 1/2 inch or so. Is there any place I can order one? It bolts to the harmonic balancer using 3 allen bolts. There is also a alternator pulley on the inside that is lined up perfectly. The p/s pulley is the outside one. Any help is appreciated. Lumpy

------------------
67 Chevy,Short/Fleet,350,Saginaw 4-Speed,Lowered 4x2,small window,P/S,Edelbrock Intake/Carb,HEI,Gear Drive,Crane Cams 274h
Three Rivers, Ca
Pic at: <A HREF="http://community.webshots.com/album/29068416etoBoEninp
" TARGET=_blank>http://community.webshots.com/album/29068416etoBoEninp
</A>

*Fast68Chevy* · 03-27-2002, 08:11 PM

well sine its a 67 with an incorrect engine in it, then its probably way kimmy rigged up, does the engien have a long or short water pump ? i have both the flat pulley that sits directly on the balancer in 67-72 and also i have the 1 /3/4" wide dished pulley thats the add-on for p/s belt in 67-72

what numbers are stamped onto your pullies ?
and do you have corr4ect p/s pump brackets ? the ones that extend back to the engine mount ?

------------------
-71/C-10(thx teeitup and crews!)350 4+4/CH465(thx 71Chev, GMCPaul, and CPNE)longfleet bed(thnx meathead95)!still building it-
-'84 Z28(Z28) 1G1AP87GXEL100000 with H.O. 305/4bbl/190net/hp(L69) 3.73 rear(GT4/YC4) 700R4(MD8-MXO) & other goodies

-79 G20 pass van, 350/th350/10bolt,
paint is overrated
Randy- Lincoln, IL

r68c30@hotmail.com
© RSS Enterprises 2000

Lumpy · 03-27-2002, 08:28 PM

Fast. It is a short water pump. The P/S bracket is like you said and goes back and mounts to the motor mount. I have a single groove pulley for the water pump that is flat and the i have that dished one like you said for the p/s. But the dished one does not line up good with the P/S pulley. The crank p/s pulley is about 1/2 off closer to the radiator then the actual P/S pulley. Can I just order a double groove crank pulley? Thanks.... Lumpy

Lumpy · 03-27-2002, 08:29 PM

Oh yea.. Both crank pulleys measure approximately 6.75 inchesin diameter. I cant see a number on the pulley. Thanks

gregsplace · 03-27-2002, 08:58 PM

p/s pump could have wrong pulley on it, should be flat pulley, not the dished back one, if I remember right.

Lumpy · 03-27-2002, 09:08 PM

Greg,
The P/S pump pulley does have a bit of a dish to it. If it were flat it appears it would line up perfectly. But since my crank p/s pulley is bent it looks like I may be able to use an aftermarket aluminum double groove crank pulley it it would line up.

03-27-2002, 06:04 PM	#1
Lumpy 2 tons of fun Join Date: Dec 2001 Location: Central, Ca Posts: 194	Where to find P/S pulley? Hello, I have a 67 pickup with a 350 in it. The power steering pulley is bent and I would like to replace it. I don't think it is the right one anyways because the pulley on the crank and the pulley on the p/s pump are not lined up right. They are off by maybe 1/2 inch or so. Is there any place I can order one? It bolts to the harmonic balancer using 3 allen bolts. There is also a alternator pulley on the inside that is lined up perfectly. The p/s pulley is the outside one. Any help is appreciated. Lumpy ------------------ 67 Chevy,Short/Fleet,350,Saginaw 4-Speed,Lowered 4x2,small window,P/S,Edelbrock Intake/Carb,HEI,Gear Drive,Crane Cams 274h Three Rivers, Ca Pic at: <A HREF="http://community.webshots.com/album/29068416etoBoEninp " TARGET=_blank>http://community.webshots.com/album/29068416etoBoEninp </A> __________________ 67 Chevy,Short/Fleet,350,Saginaw 4-Speed,Lowered 4x2,small window,P/S,Edelbrock Intake/Carb,HEI,Gear Drive,Crane Cam 274H Three Rivers, Ca Pics at: http://www.cardomain.com/id/lumpy454

03-27-2002, 08:28 PM	#3
Lumpy 2 tons of fun Join Date: Dec 2001 Location: Central, Ca Posts: 194	Fast. It is a short water pump. The P/S bracket is like you said and goes back and mounts to the motor mount. I have a single groove pulley for the water pump that is flat and the i have that dished one like you said for the p/s. But the dished one does not line up good with the P/S pulley. The crank p/s pulley is about 1/2 off closer to the radiator then the actual P/S pulley. Can I just order a double groove crank pulley? Thanks.... Lumpy __________________ 67 Chevy,Short/Fleet,350,Saginaw 4-Speed,Lowered 4x2,small window,P/S,Edelbrock Intake/Carb,HEI,Gear Drive,Crane Cam 274H Three Rivers, Ca Pics at: http://www.cardomain.com/id/lumpy454

03-27-2002, 08:29 PM	#4
Lumpy 2 tons of fun Join Date: Dec 2001 Location: Central, Ca Posts: 194	Oh yea.. Both crank pulleys measure approximately 6.75 inchesin diameter. I cant see a number on the pulley. Thanks __________________ 67 Chevy,Short/Fleet,350,Saginaw 4-Speed,Lowered 4x2,small window,P/S,Edelbrock Intake/Carb,HEI,Gear Drive,Crane Cam 274H Three Rivers, Ca Pics at: http://www.cardomain.com/id/lumpy454

03-27-2002, 08:58 PM	#5
gregsplace Senior Member Join Date: Dec 2000 Location: Colwich,Kansas Posts: 713	p/s pump could have wrong pulley on it, should be flat pulley, not the dished back one, if I remember right. __________________ 67 3/4 4x4 402,a/t,flat bed 98 GMC Sierra swb daily driver 87 burb parting out. 68 1/2 chevy, 350/350, 71 gmc frame, kid's beater 69 1ton 396-4sp, dump 69 swb stepside 396/400th current frameup 67 swb 454/400th rebuilding now, oldest boy just rolled it 99,HD, Road King Classic Colwich Ks

03-27-2002, 09:08 PM	#6
Lumpy 2 tons of fun Join Date: Dec 2001 Location: Central, Ca Posts: 194	Greg, The P/S pump pulley does have a bit of a dish to it. If it were flat it appears it would line up perfectly. But since my crank p/s pulley is bent it looks like I may be able to use an aftermarket aluminum double groove crank pulley it it would line up. __________________ 67 Chevy,Short/Fleet,350,Saginaw 4-Speed,Lowered 4x2,small window,P/S,Edelbrock Intake/Carb,HEI,Gear Drive,Crane Cam 274H Three Rivers, Ca Pics at: http://www.cardomain.com/id/lumpy454

03-27-2002, 08:11 PM	#2
Fast68Chevy Account Suspended Join Date: May 2000 Location: IL Posts: 0	well sine its a 67 with an incorrect engine in it, then its probably way kimmy rigged up, does the engien have a long or short water pump ? i have both the flat pulley that sits directly on the balancer in 67-72 and also i have the 1 /3/4" wide dished pulley thats the add-on for p/s belt in 67-72 what numbers are stamped onto your pullies ? and do you have corr4ect p/s pump brackets ? the ones that extend back to the engine mount ? ------------------ -71/C-10(thx teeitup and crews!)350 4+4/CH465(thx 71Chev, GMCPaul, and CPNE)longfleet bed(thnx meathead95)!still building it- -'84 Z28(Z28) 1G1AP87GXEL100000 with H.O. 305/4bbl/190net/hp(L69) 3.73 rear(GT4/YC4) 700R4(MD8-MXO) & other goodies -79 G20 pass van, 350/th350/10bolt, paint is overrated Randy- Lincoln, IL r68c30@hotmail.com © RSS Enterprises 2000



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.