The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-15-2013, 11:48 AM   #1
Mgicm
Registered User
 
Join Date: Sep 2013
Location: Nashville, tn
Posts: 163
A mess.. sheetmetal nightmare

Hi everyone
So I ripped off these replacement panels on my 51 AD which were put over the original floors and of course found a mess. Some of it I expected and some I did not. My issue is that the rust extended into the kickpanel area. I am trying to figure out what it SHOULD look like. Does anyone have pictures of the inside of the cab, no floor or maybe just before a replacement floor panel is put in? I am trying to see, specifically the passenger side, what it should look like in the area where the rocker ends, floor support and the kick panel. Is there a replacement sheet metal piece that can be purchased for this area? It is not even the kick panel I am having issues with but behind it..the part that is seen when you take fender off. Will try to get a picture.

When welding in the floor pan, is there a best way to do this? Should it be a perfect fit or ok to overlap just a bit with seam sealer? Looking for advice on this.

thanks!

Last edited by Mgicm; 12-15-2013 at 12:02 PM.
Mgicm is offline   Reply With Quote
Old 12-15-2013, 11:52 AM   #2
Atommik
Registered User
 
Atommik's Avatar
 
Join Date: Sep 2011
Location: Golden Valley,MN
Posts: 639
Re: A mess.. sheetmetal nightmare

What year is your truck?
Atommik is offline   Reply With Quote
Old 12-15-2013, 12:03 PM   #3
Mgicm
Registered User
 
Join Date: Sep 2013
Location: Nashville, tn
Posts: 163
Re: A mess.. sheetmetal nightmare

doh sorry.. 51 AD.. edited post

FOund a pic here - the area I need is the ones with the beading shown here. Where do you get these pieces?


Last edited by Mgicm; 12-15-2013 at 12:08 PM.
Mgicm is offline   Reply With Quote
Old 12-15-2013, 01:59 PM   #4
youngrodder
Registered User
 
youngrodder's Avatar
 
Join Date: Mar 2007
Location: Scotts, Michigan
Posts: 3,774
Re: A mess.. sheetmetal nightmare

Quote:
Originally Posted by Mgicm View Post
doh sorry.. 51 AD.. edited post

FOund a pic here - the area I need is the ones with the beading shown here. Where do you get these pieces?

You can get them from most vendors. Here are just a few sources:
http://www.classicparts.com/

https://www.chevsofthe40s.com/

http://www.brotherstrucks.com/

You can also find panels on Ebay.

Marc
__________________
…………...........__________
.................. ((__|__||___\____
..;.;;.:;:;.,;..;((_(O))____ (_(O))

1948 Chevy Truck - Finished SOLD!!

1953 Chevy Suburban "Family Truckster" Completed: Spring of 2021
http://67-72chevytrucks.com/vboard/s...d.php?t=605484

1994 4x4 Blazer - "Field Find"
https://67-72chevytrucks.com/vboard/...ferrerid=30857
youngrodder is offline   Reply With Quote
Old 12-15-2013, 04:33 PM   #5
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,710
Re: A mess.. sheetmetal nightmare

I'd think that almost all of the purveyors of AD truck parts stock that panel. They also should have the inner panel if you need it.

Here is the LMC link. I usually check it to see if a part exists just because it is easy to get around in the catalog on and they show somewhat how the parts go together. http://www.lmctruck.com/icatalog/ca/full.aspx?Page=22
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is online now   Reply With Quote
Old 12-15-2013, 08:16 PM   #6
pgf545
Registered User
 
pgf545's Avatar
 
Join Date: May 2006
Location: Santa Fe,Texas
Posts: 933
Re: A mess.. sheetmetal nightmare

Take a look at my build page on page 3-5 and there are a few pictures of ours torn apart. I put the front floor, firewall. inner kick panels and the outer cowl panel. I think the outer cowl panel replacement is on page 10. I might have some more pictures if you don't see what you need on those. If you have any questions let me know.

Bernie
__________________
52 Chevy Truck (Dad's)
http://67-72chevytrucks.com/vboard/s...d.php?t=206021
pgf545 is offline   Reply With Quote
Old 12-16-2013, 10:57 AM   #7
Mgicm
Registered User
 
Join Date: Sep 2013
Location: Nashville, tn
Posts: 163
Re: A mess.. sheetmetal nightmare

Thanks everyone. I think my confusion is that when i went inside the cab passenger size, there is a kick panel piece there with a large rectangular opening. But when I go to the outside in the cowl/fender area I believe there was a second piece of metal there with tons of bondo on it. Dumb question but should that kick panel be the only piece there?

Also, does anyone have a pic of what the rocker & supports should look like at the front of the cab and also the rear? This guy made his own and there is rocker rust but I cant tell what it is supposed to look like. Where do the floor supports connect.. to the rocker? Trying to see where these floor supports connect and where rocker should end.

Will try to add some pics of what i have going on.
Mgicm is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:04 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com