The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-10-2014, 06:22 PM   #1
dhughins
Registered User
 
dhughins's Avatar
 
Join Date: Aug 2007
Location: ozark, al
Posts: 583
Speedo reads 20 sitting still and fuel gauge moves toward e when I turn lights on.

I recently got truck and the electrical part is all hacked up. The speedo reads 20 and goes up when I drive. I'm not sure if it's just 20 off all the time or worse. When I turn on the lights the fuel gauge starts going to e until it's all the way left. Turn off lights and it goes back to where it was. Any of y'all seen this before. I wanna be able to drive truck so I'm not able to completely rewire it. None of the air or heat stuff has electricity to it.
dhughins is offline   Reply With Quote
Old 05-10-2014, 09:38 PM   #2
rich weyand
Registered User
 
rich weyand's Avatar
 
Join Date: Apr 2014
Location: Bloomington Indiana
Posts: 1,041
Re: Speedo reads 20 sitting still and fuel gauge moves toward e when I turn lights on

You should tell us the year of your truck, as the wiring changed over time.

That being said, the first place to look is grounds. There are four electrically isolated parts on these trucks: the battery, the engine, the cab, and the frame+bed. They are electrically isolated due to the rubber mounts on the engine and on the cab.

So, to connect four things together so they all agree on ground, you need three wires. One is obvious: the big black cable from the battery ground to the alternator bracket. The other two (depending on the year) are copper braids from the rear of the passenger side head to the firewall, and from the front of the driver side head to the frame rail. These are often left off when engines are replaced or repaired, and then people can't figure out why their gas gauge reading changes when the lights are turned on, for example.

Do you have both of these grounds? If not, install them first. You can use 12 AWG wire rather than copper braid if you want. Here are where they go on most years.



__________________
Rich Weyand

1978 K10 RCSB DD.
rich weyand is offline   Reply With Quote
Old 05-11-2014, 07:51 AM   #3
dhughins
Registered User
 
dhughins's Avatar
 
Join Date: Aug 2007
Location: ozark, al
Posts: 583
Re: Speedo reads 20 sitting still and fuel gauge moves toward e when I turn lights on

Sorry it's an 85. I know there is a big braided ground from engine to frame on passenger side. Gotta look for the rest. Thx.
dhughins is offline   Reply With Quote
Old 05-11-2014, 08:34 AM   #4
MalibuSSwagon
Registered User
 
Join Date: Sep 2009
Location: Weare,NH
Posts: 1,592
Re: Speedo reads 20 sitting still and fuel gauge moves toward e when I turn lights on

85 would have a cable drive speedo originally, so unless it's been swapped for a later speedo, would not be related to an electrical problem.
MalibuSSwagon is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:46 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com