3 point seat belts 1964 c-10 truck

[crowdaddy]

Seat belts are a must in my family, and so I'm looking for others that have put regular seat belts in their trucks. I've heard s-10 belts work well, but I would like to hear about people that are using them or other 3 pt belt systems. I don't believe in 64 there were any pre drilled spots for the belts yet. Any ideas pictures would be helpful.

[TypeSL2]

I too am curious about this as well. I recently bought some seats that have the 3 point belts all contained in the seat, but would like to open my options for if I decide to use a different seat later.

James

[1963c-10]

A good thread on installing 3 point belts in a 64-66 cab. I believe 66 was the 1st year with the 3 point belt provision.

Link: http://67-72chevytrucks.com/vboard/s...d.php?t=564865

[64fleetside]

I used belts from a 98 Silverado.

[crowdaddy]

Originally Posted by 64fleetside

I used belts from a 98 Silverado.

Thanks guys, I'm getting educated, checking it out!!

[corvettejim1968]

66 was the 1st year seat belts were standard. im pretty sure LMC has the 3 point harness . mine are just lap belts but here are some pics of what i did.

[Woogeroo]

Juliano's


For more ideas and options see the Seat Belts category of
your 60-66 FAQ Index.

-W


NOTE : if this link changes in the future, look for the sticky at the
top of the 1960-66 Message Board.

[crowdaddy]

Originally Posted by corvettejim1968

66 was the 1st year seat belts were standard. im pretty sure LMC has the 3 point harness . mine are just lap belts but here are some pics of what i did.

Nice job corvette jim…..I'll be looking in those areas for drilling…..

[corvettejim1968]

thanks if i remember correctly there was a spot weld at the point i drilled into. made it easy. and i bought the spring wind up on year one web site under impala. its the same seat belt option for our trucks according to my brochure.

[AcampoDave]

Got these from Juliano's Interior Products. They come with a nice set of anchor plates with the nut welded on. For the shoulder harness, I drilled the hole using and old socket for a drill stop and then taped the anchor to a stick and fished it up there till I saw the nut, then threaded in the bolt. I did remove my tank to facilitate installation on the drivers side.

[PGSigns]

I got mine from here. http://www.andoauto.com/Truck-R.htm Very nice and have been working well for the last several months since I got them in.
Jimmy

[TopFuel1966]

Juliano's

[AcampoDave]

Top fuel 1966 your interior is beautiful, and wow 1 piece side glass to boot!

[crowdaddy]

Originally Posted by AcampoDave

Top fuel 1966 your interior is beautiful, and wow 1 piece side glass to boot!

Nice seat belts everyone! I'm looking at the placements, thinkin about where to get them and anxiously awaiting my 230 rebuild and the return of my truck.

[crowdaddy]

Originally Posted by AcampoDave

Got these from Juliano's Interior Products. They come with a nice set of anchor plates with the nut welded on. For the shoulder harness, I drilled the hole using and old socket for a drill stop and then taped the anchor to a stick and fished it up there till I saw the nut, then threaded in the bolt. I did remove my tank to facilitate installation on the drivers side.

Ampco dave, nice shot of the high point in the cab and tip about the tank. I would have asked that question eventually, you guys don't miss nothin'.

[66BigBackWindow]

Wow, these all have great info. I will look back on this when I redo mine.

[TopFuel1966]

Originally Posted by AcampoDave

Top fuel 1966 your interior is beautiful, and wow 1 piece side glass to boot!

Thanks. It looks better since the photos. The white inserts in the door panels went away. The white worked with the original beige but not so with the red IMO.