5" bolt pattern on a 9" - The 1947 - Present Chevrolet & GMC Truck Message Board Network

NDWEEDS · 08-20-2014, 10:57 PM

I'm installing a Ford 9 inch in my 1955 2nd but need a 5x5 bolt pattern. Can the stock axles be converted to 5x5 (welded and re-drilled)? Are there any after market axle companies that make 5x5 shafts?

Donaldo · 08-20-2014, 11:01 PM

Check out Moser Engineering

1project2many · 08-21-2014, 07:16 AM

I've redrilled axles, rotors, and drums before. It's not that hard with a compass and some patience. And a good drill press. With 5 lug you put the new holes between existing holes. You also want to check the axle center to make sure it's right for your wheels and brakes. Too small and it won't provide the centering you need. Too large and you can't get the drum/rotor/wheel installed.

Moser will make axles to your specs.

**mr48chev** · 08-21-2014, 10:57 AM

Check with Steve at Industrial Chassis in Phoenix. If he can't do it he will know who can do it right. http://www.industrialchassisinc.com/

It's a pretty common machine shop task but you want the right shop doing it.

Both Mosier and Dutchmans motor Sports do it if you want to ship the axles off.

**G&R's57GMC** · 08-21-2014, 01:46 PM

The most obvious choice is call Currie, after all they are the leader and manufacture of the NEW 9" and can set you up with anything you need for a 9"

http://www.currieenterprises.com

Donaldo · 08-22-2014, 03:22 PM

""The most obvious choice is call Currie, after all they are the leader and manufacture of the NEW 9" and can set you up with anything you need for a 9" ""

That might be fine for those with deep pockets, but for many that expense is not an option. I usually have to re-adapt, fix and make work with what I have, make it work in the most economical way I can.

My truck came to me with a GM 12 bolt rear end, with 4 3/4" back set rims it is still 7" too wide for the tires to fit under the fenders. So whack off 3 1/2" off each side, some welding and Moser axles, new bearings and a few hours of my time it will still be under a Grand. which is a lot closer to affordable here in retirement. :) I do realize I am building this for Me to drive, not a paying client/customer.

67GMCkid · 08-22-2014, 04:45 PM

A few months ago I was shopping for 5 on 5 custom axles for the boys leaf spring 6 lug Dana 44 rear.. I called all the big name axle manufactures, let me tell you, I don't know how some of these phone techs get their ego swollen heads thru the door in the morning.. The act to busy to answer questions.. one was just totally arrogant..

But I will say we went with Duchman these people were fantastic no question was to small or insignificant phone calls were returned...
Total for new axles with studs, retainers, access holes, bearings $417 and they were in or hands in a little less than 2 weeks..
When I install one of these Dana 44's in my 52 I will be ordering another set from them!

08-20-2014, 10:57 PM	#1
NDWEEDS Registered User Join Date: Feb 2014 Location: Phoenix Posts: 26	5" bolt pattern on a 9" I'm installing a Ford 9 inch in my 1955 2nd but need a 5x5 bolt pattern. Can the stock axles be converted to 5x5 (welded and re-drilled)? Are there any after market axle companies that make 5x5 shafts?

08-20-2014, 11:01 PM	#2
Donaldo Registered User Join Date: Sep 2013 Location: Morro Bay, California Posts: 447	Re: 5" bolt pattern on a 9" Check out Moser Engineering __________________ Thanks, Don http://www.donsbirds.com/pick-up

08-21-2014, 07:16 AM	#3
1project2many Registered User Join Date: Mar 2012 Location: Lakes Region NH Posts: 3,200	Re: 5" bolt pattern on a 9" I've redrilled axles, rotors, and drums before. It's not that hard with a compass and some patience. And a good drill press. With 5 lug you put the new holes between existing holes. You also want to check the axle center to make sure it's right for your wheels and brakes. Too small and it won't provide the centering you need. Too large and you can't get the drum/rotor/wheel installed. Moser will make axles to your specs.

08-21-2014, 10:57 AM	#4
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,711	Re: 5" bolt pattern on a 9" Check with Steve at Industrial Chassis in Phoenix. If he can't do it he will know who can do it right. http://www.industrialchassisinc.com/ It's a pretty common machine shop task but you want the right shop doing it. Both Mosier and Dutchmans motor Sports do it if you want to ship the axles off. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

08-21-2014, 01:46 PM	#5
G&R's57GMC Senior Member Join Date: Aug 2010 Location: Shasta Lake, CA. Posts: 1,624	Re: 5" bolt pattern on a 9" The most obvious choice is call Currie, after all they are the leader and manufacture of the NEW 9" and can set you up with anything you need for a 9" http://www.currieenterprises.com __________________ Glen & Jane's Rides ‘57 GMC NAPCO Long Bed V8 4 speed Bought 2008 7 other cars & trucks , 5 trailers '56 Chevy Long Bed I6, 4 speed Bought 1990 Sold 8.22.2020 ’56 GMC Suburban Pickup V8, 4 speed Hydramatic Bought 1996 Sold 10.11.2020 My Other Tinkerings http://67-72chevytrucks.com/vboard/s...75#post8967275

08-22-2014, 03:22 PM	#6
Donaldo Registered User Join Date: Sep 2013 Location: Morro Bay, California Posts: 447	Re: 5" bolt pattern on a 9" ""The most obvious choice is call Currie, after all they are the leader and manufacture of the NEW 9" and can set you up with anything you need for a 9" "" That might be fine for those with deep pockets, but for many that expense is not an option. I usually have to re-adapt, fix and make work with what I have, make it work in the most economical way I can. My truck came to me with a GM 12 bolt rear end, with 4 3/4" back set rims it is still 7" too wide for the tires to fit under the fenders. So whack off 3 1/2" off each side, some welding and Moser axles, new bearings and a few hours of my time it will still be under a Grand. which is a lot closer to affordable here in retirement. :) I do realize I am building this for Me to drive, not a paying client/customer. __________________ Thanks, Don http://www.donsbirds.com/pick-up

08-22-2014, 04:45 PM	#7
67GMCkid Registered User Join Date: Jun 2012 Location: Etters Pa Posts: 197	Re: 5" bolt pattern on a 9" A few months ago I was shopping for 5 on 5 custom axles for the boys leaf spring 6 lug Dana 44 rear.. I called all the big name axle manufactures, let me tell you, I don't know how some of these phone techs get their ego swollen heads thru the door in the morning.. The act to busy to answer questions.. one was just totally arrogant.. But I will say we went with Duchman these people were fantastic no question was to small or insignificant phone calls were returned... Total for new axles with studs, retainers, access holes, bearings $417 and they were in or hands in a little less than 2 weeks.. When I install one of these Dana 44's in my 52 I will be ordering another set from them!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.