The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-22-2014, 05:05 PM   #1
higXtech
Registered User
 
higXtech's Avatar
 
Join Date: Sep 2012
Location: Leesburg VA
Posts: 85
Ripping out my ridetech ridepro system - going manual via little larrys

I'm done with electric solenoids and pressure sensors.

I went to drive the truck this morning.. valves were frozen, pressure sensors failing etc.. Not the first time either. I've had a list of issues. While the novelty of a truck that raised itself to ride height was fun for a while, I value reliability more.

I just ordered little larry's fourplay:http://www.littlelarrys.net/ -- It comes with 4 1/8" NPT ports for gauge connections.

I'm looking for some bulletproof dual needle gauges. Any suggestions?

thanks!
__________________
--
1968 fleetside - nolimit wide ride front and rear + ridetech
higXtech is offline   Reply With Quote
Old 12-22-2014, 05:41 PM   #2
CHRIS67GMC
Registered User
 
CHRIS67GMC's Avatar
 
Join Date: Aug 2007
Location: Tiffin Oh
Posts: 299
Re: Ripping out my ridetech ridepro system - going manual via little larrys

Nothing is bullet proof if its full of water and freezing. Firestone has gauges.
CHRIS67GMC is offline   Reply With Quote
Old 12-22-2014, 05:59 PM   #3
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
Re: Ripping out my ridetech ridepro system - going manual via little larrys

I hope your experience with the Little Larrys Four Play is better than mine.

I've had problems since minute one with the valves leaking. I'm about to take it back out and blow it completely apart for a full rebuild with new o rings and a thorough cleaning. They either built it with crappy o rings or there was machining rubbish left internally when they assembled it. Either way, it hasn't worked right yet, and I haven't even gotten past the build stage in the shop and even driven the truck on the road yet.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline   Reply With Quote
Old 12-22-2014, 06:26 PM   #4
higXtech
Registered User
 
higXtech's Avatar
 
Join Date: Sep 2012
Location: Leesburg VA
Posts: 85
Re: Ripping out my ridetech ridepro system - going manual via little larrys

Quote:
Originally Posted by Tx Firefighter View Post
I hope your experience with the Little Larrys Four Play is better than mine.

I've had problems since minute one with the valves leaking. I'm about to take it back out and blow it completely apart for a full rebuild with new o rings and a thorough cleaning. They either built it with crappy o rings or there was machining rubbish left internally when they assembled it. Either way, it hasn't worked right yet, and I haven't even gotten past the build stage in the shop and even driven the truck on the road yet.
Oh sorry to hear that. Little Larry's is within driving distance. I hope I will not have to make that trip.
__________________
--
1968 fleetside - nolimit wide ride front and rear + ridetech
higXtech is offline   Reply With Quote
Old 12-22-2014, 06:32 PM   #5
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
Re: Ripping out my ridetech ridepro system - going manual via little larrys

When I first unboxed my unit, two of the switches felt a bit crunchy when moved.

When I first installed it, on a couple of the switches, when you hit "up" and then released the switch, it would continue to go up slowly until you horsed it around up and down back and forth. Then it would hold steady pressure. Kind of disconcerting to raise your truck to a set pressure and take your hand away and then just watch it continue to climb and climb without you doing anything.

Now, my front right valve is leaking down. Bad. Like full raise (80 psi or so) to zero in about 30 minutes.

All of this on a truck that hasn't ever even been driven yet. I spoke with LL guy on Facebook and ran air tool oil through my system to lubricate the orings. No help from that.

I don't have the time or inclination to fool around with it. I'm just gonna jerk it back out, blow it apart, and get good proper o rings to replace whatever is in it right now. I'll clean it surgically clean, inspect all machining carefully, and reassemble with good quality, well lubricated o rings. Unless there is a significant error in their machine work, I feel fairly confident I can get it fixed quicker than trying to hassle with sending it back for warranty.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline   Reply With Quote
Old 12-23-2014, 03:11 AM   #6
andrewmp6
Registered User
 
Join Date: Jan 2009
Location: Louisville,Ky
Posts: 5,811
Re: Ripping out my ridetech ridepro system - going manual via little larrys

Any valve can freeze if you don't keep water out of the system and run airline anti freeze in the winter months.
andrewmp6 is offline   Reply With Quote
Old 12-24-2014, 12:38 AM   #7
theastronaut
Registered User
 
theastronaut's Avatar
 
Join Date: May 2011
Location: Anderson SC
Posts: 3,901
Re: Ripping out my ridetech ridepro system - going manual via little larrys

Look into Dloe's manual valves. Haven't heard any bad feedback on them, only good reviews.

http://dloesvalves.webstarts.com/ind...20130106230440
theastronaut is offline   Reply With Quote
Old 12-24-2014, 05:52 PM   #8
higXtech
Registered User
 
higXtech's Avatar
 
Join Date: Sep 2012
Location: Leesburg VA
Posts: 85
Re: Ripping out my ridetech ridepro system - going manual via little larrys

Quote:
Originally Posted by andrewmp6 View Post
Any valve can freeze if you don't keep water out of the system and run airline anti freeze in the winter months.
We agree on that. When ridetech sells a complete kit. It should be a complete kit.
__________________
--
1968 fleetside - nolimit wide ride front and rear + ridetech
higXtech is offline   Reply With Quote
Old 12-24-2014, 08:22 PM   #9
lolife99
67-72 parts collector,…
 
lolife99's Avatar
 
Join Date: Nov 2002
Location: Mid-MO
Posts: 22,700
Re: Ripping out my ridetech ridepro system - going manual via little larrys

How would air line antifreeze stay where you want it?
Never heard of using it in an air suspension system.
Wouldn't you blow it out when you dumped the bags?
Just trying to understand.

The key is to have dry air.
Whether that means routinely draining your air tank or running some type of air dryer.
Either way,... I don't think the air management manufacturer can be held liable for how much water your air compressors generate, how much YOU run the compressors, or how much moisture is in your system. (condensation)
__________________
Keith

Convert to disc brakes.
http://67-72chevytrucks.com/vboard/s...d.php?t=444823

Last edited by lolife99; 12-24-2014 at 11:15 PM.
lolife99 is offline   Reply With Quote
Old 12-24-2014, 10:45 PM   #10
RRR18
Senior Member
 
RRR18's Avatar
 
Join Date: Nov 2010
Location: Lordstown, OH / Wentzville, MO
Posts: 870
Re: Ripping out my ridetech ridepro system - going manual via little larrys

I have same questions Keith has.
__________________
'67 BAD IDEA

Follow on Instagram https://www.instagram.com/rtimes3c10/

Ryan
RRR18 is offline   Reply With Quote
Old 12-24-2014, 11:51 PM   #11
Chevysdominate
Registered User
 
Chevysdominate's Avatar
 
Join Date: Jul 2006
Location: Springtucky, Oregon
Posts: 265
Re: Ripping out my ridetech ridepro system - going manual via little larrys

I have the Dloe manual valves and im very happy with them. I've had them for a few years with no issues.
Attached Images
 
Chevysdominate is offline   Reply With Quote
Old 12-25-2014, 12:07 AM   #12
Chevysdominate
Registered User
 
Chevysdominate's Avatar
 
Join Date: Jul 2006
Location: Springtucky, Oregon
Posts: 265
Re: Ripping out my ridetech ridepro system - going manual via little larrys

I've been thinking about how to dry the air from the on-board tanks. What i'm going to try is an air conditioner filter dryer. They are really good at removing moisture and particles from gas and liquid. A decent sized filter dryer should work fine for a long time. Unless you are playing with the valves a lot in a moist climate. You could then take it off, bake it in an oven to remove the water then re-install.

Quote:
Originally Posted by lolife99 View Post
How would air line antifreeze stay where you want it?
Never heard of using it in an air suspension system.
Wouldn't you blow it out when you dumped the bags?
Just trying to understand.

The key is to have dry air.
Whether that means routinely draining your air tank or running some type of air dryer.
Either way,... I don't think the air management manufacturer can be held liable for how much water your air compressors generate, how much YOU run the compressors, or how much moisture is in your system. (condensation)
Chevysdominate is offline   Reply With Quote
Old 12-25-2014, 01:59 AM   #13
andrewmp6
Registered User
 
Join Date: Jan 2009
Location: Louisville,Ky
Posts: 5,811
Re: Ripping out my ridetech ridepro system - going manual via little larrys

Chevydominate they do make water traps for air ride http://www.avsontheweb.com/water-traps/ Most run the line between the compressor to tank with a check valve then water trap.I have seen some run a water trap before the tank and between the tank and valves.I would run just the one between the compressor and tank and the winter months a few oz of airline anti freeze that the semis run it works.
andrewmp6 is offline   Reply With Quote
Old 12-27-2014, 02:19 AM   #14
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Re: Ripping out my ridetech ridepro system - going manual via little larrys

I don't get how a trap between the comp & tank can be effective. The air doesn't have moisture to be removed until it cools & condenses. It's in the tank by then.

Seems 'traps/filters' should be after the tank & before the valves. An automated tank purge like DOT regulated stuff would help alot.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 12-27-2014, 12:41 PM   #15
Snailed
Registered User
 
Snailed's Avatar
 
Join Date: Jul 2013
Location: Portland, Maine
Posts: 219
Re: Ripping out my ridetech ridepro system - going manual via little larrys

The height of the components matters and is a key element of collecting condensation in all compressed air systems on-road or not.

I have my tank as the lowest point in the system with the pumps slightly higher and a water trap between the tank and valves with it's lowest point at the top of the tank. The valves are the highest point in the system and inside the cab. I have yet to get any moisture out of the water trap in about 200 pump cycles and no freezing.
__________________
Daily Driver '66 C10 Fleetside Short Bed - LS swap - 4L80E - Accuair eLevel
Snailed is offline   Reply With Quote
Reply

Bookmarks

Tags
manual, valves


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:33 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com