GA parting out 79 K-10

[roundhouse]

In Atlanta

frame, no rust. $100
TH-350 $75
NP-205 fixed yoke $275
driveshafts, $50
sliding back window $40
seat belts (blue )$30
non tilt column for manual transmission $50
tailgate $50

door glass $20
window regulators $20 each
windshield $40
grill $50
core support $100


3/4 ton 8 lug 14 bolt Full Floater 3.73 posi $400
3/4 ton 10 bolt front 8 lug 3.73 open $300
more parts avail

clutch & brake pedal assy $50
gauge cluster $40
dash trim black $20


bedliner $30

will cut patch panels but has usual rust in floor and cab corners and rockers,
bed is good except for right behind wheels

Im looking for stepside roll bar !

[Chaplain]

Passenger door manual window regulator?

[old Rusty C10]

I need all the springs from the clutch linkage on the bottom and the two springs that are under the dash board for the clutch pedal return. Also if the on air conditioning selector switch is good give e a price for that too all is shipped to 07731

[roundhouse]

Originally Posted by Chaplain

Passenger door manual window regulator?

$20 plus shipping

[roundhouse]

Originally Posted by old Rusty C10

I need all the springs from the clutch linkage on the bottom and the two springs that are under the dash board for the clutch pedal return. Also if the on air conditioning selector switch is good give e a price for that too all is shipped to 07731

Like to sell the pedal assembly whole

Think I have the spring from the linkage under neath the truck
Gotta check
Think AC switch is already gone

[79 Silverado/454]

Is the sliding back window a factory window ? If so I would be interested and would like to see pics.

[roundhouse]

Originally Posted by 79 Silverado/454

Is the sliding back window a factory window ? If so I would be interested and would like to see pics.

I think so
Its different than the one in my 77
I will post up pics soon

[old Rusty C10]

If you include the both springs theres one that is attached from the clutch pedal to the top of the pedal assembly and another that is attached from the pedal to the bottom of the pedal assembly near the dash and steering column I will gladly buy the whole assembly . I assume this is NOT a hydraulic clutch upgrade

[Chaplain]

Originally Posted by roundhouse

$20 plus shipping

PM sent

[roundhouse]

Originally Posted by old Rusty C10

If you include the both springs theres one that is attached from the clutch pedal to the top of the pedal assembly and another that is attached from the pedal to the bottom of the pedal assembly near the dash and steering column I will gladly buy the whole assembly . I assume this is NOT a hydraulic clutch upgrade

stand by let me count the springs.

I converted the linkage in my driver to hydraulic so I could swap in a NV3500 and we had to cut the spring off,

[roundhouse]

Originally Posted by Chaplain

Passenger door manual window regulator?

the regulator works ok, but the splines on the shaft are chewed up

so its probably scrap, unless you want to swap the shafts,

Ive done that before, but its a pain,
I did it just so I could use 1982 door panels on a 73 door
the 73 door had the short shaft and the 1973 only really small rollers in the tracks

[roundhouse]

back window,

just noticed its missing one of metal edges on each of the sliders
look close you can see whats missing.

[roundhouse]

tailgate is rust free,
one small ding on bottom edge.

some screw holes from bedliner

[roundhouse]

Originally Posted by old Rusty C10

If you include the both springs theres one that is attached from the clutch pedal to the top of the pedal assembly and another that is attached from the pedal to the bottom of the pedal assembly near the dash and steering column I will gladly buy the whole assembly . I assume this is NOT a hydraulic clutch upgrade

This the springs you want?

[old Rusty C10]

YES I really only need the thinner one but I will buy the whole thing if you want I also need all the ones for the Z bar underneath

[roundhouse]

Originally Posted by old Rusty C10

YES I really only need the thinner one but I will buy the whole thing if you want I also need all the ones for the Z bar underneath

Ok think I have that one too
lemme check

[UKNOWME]

Can I see a pic of the guage cluster?

[79 Silverado/454]

Thanks for posting the pic. of the sliding window. I would like to find one a little nicer with no missing parts.

[Willowrun]

How are the interior door panels?

[roundhouse]

Originally Posted by UKNOWME

Can I see a pic of the guage cluster?

pouring rain right now,
tomorrow maybe

[roundhouse]

Originally Posted by Willowrun

How are the interior door panels?

fair,
they might clean up ok
padded armrest part is cracked, rest of panel looks ok.
will get some pics when it stops raining.

[old Rusty C10]

One more thing I will need if its good Please give m a price for the interior hood release cable and handle assembly.. the more I think about this the more I need lol I will also take the pedal assembly as I need another part from it so I might as well buy the whole thing I need the bracket that activates the brake lights

[Chaplain]

PM follow up sent

[JIMs70GMC]

Is the rear driveshaft still available? Also, just want to make sure it is the type with the slip joint in the driveshaft, not the type where the slip joint is into the tail housing of the transfer case. Shipping to 23323. Thanks,

Jim

[roundhouse]

Originally Posted by JIMs70GMC

Is the rear driveshaft still available? Also, just want to make sure it is the type with the slip joint in the driveshaft, not the type where the slip joint is into the tail housing of the transfer case. Shipping to 23323. Thanks,



Jim

its from a fixed yoke tcase, so yes it has the slip in the shaft,
but shipping that far is gonna be $$

I have 2 of em in fact