|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-04-2015, 10:38 AM
|
#1 |
|
Registered User
Join Date: Jan 2014
Location: Sacramento,California
Posts: 696
|
molded in front bumper...who's done it?
Hey guys, I have seen a thread or two in which the poster cut and molded the front bumper into the truck like a front roll pan. I tried searching but maybe I'm using the wrong terms. If you have done it could I see some pics and a little explination of what it entailed? Thanks on advance.
__________________
Built not bought! My dad always tried to convince me HEI was pointless! Welding is a lot like sex, you don't have to be great with the rod as long as you thoroughly prep the surface and your good at grinding  My build : 68 C10 Short Bed Conversion |
|
|
|
03-04-2015, 11:06 AM
|
#2 |
|
Registered User
 
Join Date: May 2007
Location: Rapid City South Dakota
Posts: 2,359
|
Re: molded in front bumper...who's done it?
There used to be a roll pan available. I don't know if they still sell them or not.
__________________
Turp Mcspray New life for an old 2wd, farm blazer http://67-72chevytrucks.com/vboard/s...d.php?t=505987 My Blazer build http://67-72chevytrucks.com/vboard/s...d.php?t=342299 |
|
|
|
|
03-04-2015, 02:21 PM
|
#3 |
|
Registered User
Join Date: Dec 2012
Location: Manitoba
Posts: 644
|
Re: molded in front bumper...who's done it?
I did it to mine. Starts on page 3 of my build thread.
|
|
|
|
|
03-04-2015, 08:13 PM
|
#4 |
|
Senior Member
 
Join Date: Dec 1999
Location: TN/VA
Posts: 6,388
|
Re: molded in front bumper...who's done it?
Mar-K makes a front roll pan
|
|
|
|
|
03-04-2015, 10:29 PM
|
#5 |
|
Registered User
Join Date: Feb 2015
Location: Hampton Va
Posts: 75
|
Re: molded in front bumper...who's done it?
I'm getting ready to take off a front roll pan to reinstall a bumper on my truck.
__________________
1971 C10 SWB ...project in the works 2000 Camaro SS....weekend warrior/racecar 2005 Caddy EXT....Tow rig |
|
|
|
|
03-05-2015, 12:36 AM
|
#6 |
|
tcoop68
Join Date: Jan 2006
Location: Cushing Oklahoma
Posts: 226
|
Re: molded in front bumper...who's done it?
I done several front and rear roll pans and I get them from Mar-K they have quality parts . I like welding them in. you will have to do a little cutting on the end of your front frame rails . Hope this helps
|
|
|
|
|
03-05-2015, 08:54 AM
|
#7 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: molded in front bumper...who's done it?
This thread isn't about off the shelf roll pans, it's about recessing/molding the front bumper back into the body
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
