The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-30-2017, 02:05 PM   #1
1953
Registered User
 
Join Date: Feb 2017
Location: Mount plesant michigan
Posts: 73
Best rear end and tranny for stock 235

Ok i want to know what is the best rear end and tranny for stock 235 engine i want good take of speed and highway, i see so much controversy on the best rear ratio, what is the best choice of rear end that has disc brakes and that can be a axle over spring on a 3600, im converting to axle over rear with frame notchs and going to do a front end swap also, basically update everything while i keep the 235 engine i have,
1953 is offline   Reply With Quote
Old 04-30-2017, 02:09 PM   #2
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,670
Re: Best rear end and tranny for stock 235

A zr2 rearend comes with 3.73 gears, locking diff and disc brakes and is 3" wider than a standard s10..its a good choice but may be hard to find..8.8 explorer rearend is also a popular choice..
mongocanfly is offline   Reply With Quote
Old 04-30-2017, 02:15 PM   #3
1953
Registered User
 
Join Date: Feb 2017
Location: Mount plesant michigan
Posts: 73
Re: Best rear end and tranny for stock 235

What is the gear ratio on a standard s10? And how does it perform with a 235
1953 is offline   Reply With Quote
Old 04-30-2017, 02:35 PM   #4
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,670
Re: Best rear end and tranny for stock 235

Could be anything from 3.08 to 4.56...would have to check rpo code to know..
GU4=3.08* GU5=3.23* GU6=3.42* GT4=3.73* GT5=4.10* HC4=4.56* ....
G80 is locking differential
mongocanfly is offline   Reply With Quote
Old 04-30-2017, 02:37 PM   #5
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,710
Re: Best rear end and tranny for stock 235

copied and pasted off an S-10 board

Most of us idiots use a 4x4 one. Those are 58" wide.

Those are:
3.42 axle ratio (opt GU6)
3.73 ratio (opt GT4)
4.11 ratio (opt H04)
3.08 ratio (opt GU4)

As far as I know, the 2wd ones had the same ratio spread, too.

Off that same board and I am not sure how accurate it is as the numbers don't match some other axle pages

2wd 54.5"
4wd 59"
ZR2 63"

Two wheel drive is too narrow for your truck as you would have to put mini tubs in.
4 wheel drive comes real close to stock. Back spacing may be an issue with some wheels though.

5 lug Dodge Dakota would give you open drive with a Mopar/Ford 5 on 4-1/2 bolt pattern with a choice of gear ratios but you want a rear out of a V8 truck as the 4 cylinder rear axles are wimpy. No disk that way though.

I put a 56 three speed and rear end in a 53 for friends of mine and they drove it all over the country after it was done but didn't drive very fast as they had a bit canopy/camper on it. It really didn't gain any road speed that way. We used engine, trans and rear axle out of the 56.

First I would figure out what lug bolt pattern I wanted to go with on the front and go from there.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 04-30-2017, 09:27 PM   #6
Jemezcrusher
Registered User
 
Join Date: Nov 2015
Location: Jemez Springs, NM
Posts: 435
Re: Best rear end and tranny for stock 235

Have a 8.8 in my 50. S10 tranny with OD. 5th gear is .72 making my 3.73 about a 265
Jemezcrusher is offline   Reply With Quote
Old 04-30-2017, 10:17 PM   #7
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: Best rear end and tranny for stock 235

keep in mind a 235 wasnt made for sustained high rpm operation, and doesnt have a ton of torque to be used in a low rpm high road speed application. try to stay around 2000-2500 rpm for continuous operation.

a 3.73 with normal sized tires (lets say, a 235/75/15) with a 235 and stock trans turning at 2000 rpm will net 46mph. 2500 rpm (probably ok for short stretches) would get 57mph. you will need more gear. higher rpm for a longer time will probably just puke oil out the breather.

overdrive is one way, there are a couple how-tos on this site for using a WC T5 trans from an S10 or camaro, just adding the .76 overdrive will make 2000 rpm a 60mph and 2500 rpm 75mph. you will probably run out of torque to overcome aerodynamics before that.

with the stock trans and a 3.07 gear, 2000 rpm will be ~75 mph. a 3.07 will likely make 1st gear of the stock trans, normally a granny stump puller, an actual useful gear. your limitation will probably be the torque of the stock engine, I think.

your stock 3600 rear gear is probably a 5.16. top speed right now at redline is probably 45 mph. they do not make new gear sets for the eaton rear, I have heard rumors of a 3.55 but never found anyone who has bought one.
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 04-30-2017, 10:59 PM   #8
svr
Registered User
 
svr's Avatar
 
Join Date: Feb 2016
Location: Othello washington
Posts: 400
Tom Langdons web site has a page that grades your trans and rear gears for the 235, if i remember correct a T5 with .72 OD and a 3.73 rear was right up there as being very good. He has other suggestions.

Last edited by svr; 04-30-2017 at 11:05 PM.
svr is offline   Reply With Quote
Old 04-30-2017, 11:03 PM   #9
1953
Registered User
 
Join Date: Feb 2017
Location: Mount plesant michigan
Posts: 73
Re: Best rear end and tranny for stock 235

Well cracked open the rear end and o have 32 ring teeth and 18 pinion teeth did the divide thing and got 1.7777778
1953 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com