The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-03-2017, 02:29 PM   #1
gigamanx
Senior Member
 
Join Date: Sep 2016
Location: Hershey, PA
Posts: 1,004
How should I fill firewall holes

Did a little searching and can't seem to find a good answer. I'd like to start filling some of the firewall holes I know I won't need on the cab. I've started marking the ones that can go. What is a good method of getting pieces to fill the holes? For the smaller screw type holes, I tried welding one and just made it bigger by melting the edge of the hole, so that's obviously not the way to do it haha. I don't want to replace the metal with a single sheet since I like the curves and bumps of the original one.

Would love to hear experiences and tips on smoothing things out!
__________________
Current Build Thread 1930 Ford Model A Modern Twist: Ford Model A Rat Rod With a Modern Twist

Build Thread Phase 1 "The Swap": 1949 3100 with S10 swap. Beginner build with ambition!

Build Thread Phase 2 "The Drop": Beginner Build with Ambition gets Air Ride
gigamanx is offline   Reply With Quote
Old 10-03-2017, 02:49 PM   #2
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
Re: How should I fill firewall holes

try

https://www.welderseries.com/

on line for some sheet metal plugs for cheap, or shop locally. clean the area well first, then if you grab a cheap stepped drill from harbor freight or whatever you can get a bunch of plugs the same size then drill the cab hole to fit the plug. that way the hole is nice and clean for welding. you can use a copper plate behind so if you have a little burn through it will stay put (weld doesn't stick to the copper). do a series of tacks around the plug, say 2 or 3, then carry on to the next plug because if you weld the whole thing at once you will warp the firewall or wherever you are welding. tack then move on, come back and extend the tack, then move on to allow cooling. soon the plug will be done. you can wipe with a wet rag to help cool and shrink the area so it doesn't warp too bad.
dsraven is offline   Reply With Quote
Old 10-03-2017, 03:16 PM   #3
bowt1ed
Registered User
 
Join Date: Apr 2011
Location: Virginia Beach, VA
Posts: 514
Re: How should I fill firewall holes

I just cut out slightly over-sized sheet metal circles, cleaned surfaces/edges, placed on the inside of firewall (helper to hold tight against), and welded from outside. With that thin a gauge, not too much filler required. As I recall, filled around 45 of them.

Cheers, Jim
Attached Images
 
bowt1ed is offline   Reply With Quote
Old 10-03-2017, 03:42 PM   #4
gigamanx
Senior Member
 
Join Date: Sep 2016
Location: Hershey, PA
Posts: 1,004
Re: How should I fill firewall holes

Quote:
Originally Posted by dsraven View Post
try

https://www.welderseries.com/

on line for some sheet metal plugs for cheap, or shop locally. clean the area well first, then if you grab a cheap stepped drill from harbor freight or whatever you can get a bunch of plugs the same size then drill the cab hole to fit the plug. that way the hole is nice and clean for welding. you can use a copper plate behind so if you have a little burn through it will stay put (weld doesn't stick to the copper). do a series of tacks around the plug, say 2 or 3, then carry on to the next plug because if you weld the whole thing at once you will warp the firewall or wherever you are welding. tack then move on, come back and extend the tack, then move on to allow cooling. soon the plug will be done. you can wipe with a wet rag to help cool and shrink the area so it doesn't warp too bad.
See now this is why I asked all you fine smart people... Funny they are called unholes. Here I was thinking I need to cut perfectly shaped pieces to fit in all manner of crazy spots on the firewall. I did not think of my step drill bits.

Quote:
Originally Posted by bowt1ed View Post
I just cut out slightly over-sized sheet metal circles, cleaned surfaces/edges, placed on the inside of firewall (helper to hold tight against), and welded from outside. With that thin a gauge, not too much filler required. As I recall, filled around 45 of them.

Cheers, Jim
That is a ridiculously smooth firewall. Nice job!

https://www.welderseries.com/Unholes-p50202282
__________________
Current Build Thread 1930 Ford Model A Modern Twist: Ford Model A Rat Rod With a Modern Twist

Build Thread Phase 1 "The Swap": 1949 3100 with S10 swap. Beginner build with ambition!

Build Thread Phase 2 "The Drop": Beginner Build with Ambition gets Air Ride
gigamanx is offline   Reply With Quote
Old 10-03-2017, 04:57 PM   #5
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
Re: How should I fill firewall holes

if you need a hand to hold the plug, and you have a few extra minutes to spare for fabbing up a quick tool, you can make a magnetic plug holder from a C clamp. just get a cheap steel C clamp and cut the very bottom off, like the bottom of the C part, so you have a vertical portion left there plus the top part of the C with the screw down part still intact. now drill up into the vertical section and run some threads into it. find a round magnet that sticks well and has a hole in the middle and is also smaller in diameter than the distance over to the threaded part of the C clamp. some dollar stores will have everything you need, the clamp and the magnet. the magnets sometimes are sold with a hook on them that is bolted on through a hole in the middle, perfect. toss the hook in the junk bin. bolt the magnet onto the bottom of the C clamp so it will hold the clamp vertical. now you can magnet the clamp onto the back side of the firewall and then screw the threaded part down so it sits level with the sheet metal and holds the plug in place. the clamp comes in handy for other stuff too.

or just use a magnet to hold the plug but then the magnetics will deform the mig welder and cause spatter. of you are torch welding then it won't matter, haha.

I think I spend more time making tools than I do working on the truck. dough head alert.
dsraven is offline   Reply With Quote
Old 10-03-2017, 05:41 PM   #6
Dan in Pasadena
Senior Member

 
Dan in Pasadena's Avatar
 
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,343
Re: How should I fill firewall holes

Quote:
Originally Posted by bowt1ed View Post
I just cut out slightly over-sized sheet metal circles, cleaned surfaces/edges, placed on the inside of firewall (helper to hold tight against), and welded from outside. With that thin a gauge, not too much filler required. As I recall, filled around 45 of them.

Cheers, Jim
^^^This^^^ is what was done with my firewall too. We stopped counting at 50 holes!

Came out good and I had wondered if it would repair decently.
Attached Images
    
__________________
'55 Big Window Shortbed,
Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's

Dan's '55 Big Window "Build" - Well, Kinda!
Dan in Pasadena is offline   Reply With Quote
Old 10-03-2017, 06:29 PM   #7
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 579
Re: How should I fill firewall holes

Well, Yesterday I would’ve said to do exactly what dsraven said.. but now I’m wondering if Jim and Dan’s method isn’t the way to go.
I may be picking up a new-to-me ‘51, and noticed it has quite the shotgun scatter of holes. Only thing different I was thinking was to zap a mig wire to it as a handle so I wouldn’t need magnets and cut off C clamps etc.
fourspeedwagon is offline   Reply With Quote
Old 10-03-2017, 08:31 PM   #8
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
Re: How should I fill firewall holes

this is what I did. 16ga. totally flat now.
Attached Images
     
dsraven is offline   Reply With Quote
Old 10-03-2017, 08:37 PM   #9
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
Re: How should I fill firewall holes

the rest of the story. cut it out so it will fit over the envoy donor
Attached Images
     
dsraven is offline   Reply With Quote
Old 10-03-2017, 08:50 PM   #10
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
Re: How should I fill firewall holes

the rest of the story. it became a donor for the envoy frame swap. really not that much more work to replace the whole thing though compared to plugging and finishing all the holes. especially if the floor is also rotten. the point is not my swap, it is the work involved to just replace the whole thing. wasn't that much really once I figured out how big to make the recess. need to remember to leave room for the gas pedal though. some guys just do a square recess so that would be easier.
Attached Images
     
dsraven is offline   Reply With Quote
Old 10-03-2017, 09:29 PM   #11
greg_h
Registered User
 
Join Date: Apr 2015
Location: Enid OK
Posts: 85
Re: How should I fill firewall holes

The advice I was given was to find a flat washer that fit the hole, weld it in, and the weld up the small hole in the washer.
greg_h is offline   Reply With Quote
Old 10-03-2017, 11:10 PM   #12
fourspeedwagon
Registered User
 
fourspeedwagon's Avatar
 
Join Date: Oct 2010
Location: Yakima Valley, Washington
Posts: 579
Re: How should I fill firewall holes

Wow! Dsraven that extended cab rig is amazing.
Now I’m off to see if there’s a build thread on that. Awesome truck
fourspeedwagon is offline   Reply With Quote
Old 10-03-2017, 11:47 PM   #13
Dan in Pasadena
Senior Member

 
Dan in Pasadena's Avatar
 
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,343
Re: How should I fill firewall holes

I suppose someone should mention one other alternative:

Aftermarket suppliers use to make a fiberglas sheet that covered the stock firewall and it had a recess in the center too. It simply bolted in behind the hood hinges and the top was shaped exactly to fit under/up against the factory pinch weld.

I don't see it offered on the one site I knew used to sell them: No Limit Engineering

CORRECTION: Gibbons lists a part number CH523 Smooth Firewall Cover. Maybe it's this part. No pics on their site.
__________________
'55 Big Window Shortbed,
Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's

Dan's '55 Big Window "Build" - Well, Kinda!

Last edited by Dan in Pasadena; 10-04-2017 at 12:38 AM.
Dan in Pasadena is offline   Reply With Quote
Old 10-04-2017, 12:02 AM   #14
iowaboynca
Registered User
 
iowaboynca's Avatar
 
Join Date: Aug 2012
Location: West Side of the valley, CA
Posts: 878
Re: How should I fill firewall holes

With all the craftsmanship, i'm a bit embarrassed to say I used various sizes of fender washers. Used either screws or small magnets to hold on to firewall to tack weld.

For the big holes cut out filler out of 18g sheet metal and tack/stitch welded.

You can see the results below.
http://67-72chevytrucks.com/vboard/s...3&postcount=97
__________________
Build: "1950" GMC -Charlotte
iowaboynca is offline   Reply With Quote
Old 10-04-2017, 06:57 AM   #15
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 209
Re: How should I fill firewall holes

I cut all mine the same size with a throatless shear and a disc grinder.
Attached Images
  
Dave0 is offline   Reply With Quote
Old 10-04-2017, 07:49 AM   #16
hogfarm
Senior Member
 
Join Date: Jan 2016
Location: Appleton Washington
Posts: 592
Re: How should I fill firewall holes

I went to the local machine shop and they gave me a coffee can full of the drops from there punch press,all different sizes
hogfarm is online now   Reply With Quote
Old 10-04-2017, 04:11 PM   #17
MARTINSR
Registered User
 
MARTINSR's Avatar
 
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
Re: How should I fill firewall holes

This is only for the small holes up to a half inch but a great trick I learned years ago from a Ron Covell basic metal working VHS tape, yes a VHS tape, that's how long ago we are talking. It was shown in the first few minutes of the video and I remember stopping it and saying to my wife, "I could take this tape out and throw it in the garbage right now, that one trick was worth what I paid for it and more!"

What you use is the metal you punch out of a hole using a Roper Whitney punch like this, the XX.



Or this one, but the holes are much smaller, the "jr."



I have to say, if you are doing a fair amount of fab work, these tools are a MUST HAVE. But in this case, you are just punching a hole in a piece of scrap metal. The piece of metal you punch out has a big dent in the middle, the piece is stretched up a little bit. You then take a hole you want to fill and you open it up using a variable bit or step bit until the hole barely fits the piece you punched out of the scrap metal. You put that piece in the hole and then with a dolly on the back you tape the piece with a flat body hammer and the piece gets larger because of the dent sticking up is now pressing into that piece and spreading it. The piece now fills the hole and stays there! A tiny bead around the edge and wham, no more hole.

Oh, and that punch, you can get dies to punch square holes and oblong holes and many others, I use them all the time! Awesome tools to have in your box.

Brian
__________________
1948 Chevy pickup
Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats!
Bought with paper route money in 1973 when I was 15.

"Fan of most anything that moves human beings"
MARTINSR is offline   Reply With Quote
Old 10-04-2017, 04:13 PM   #18
gigamanx
Senior Member
 
Join Date: Sep 2016
Location: Hershey, PA
Posts: 1,004
Re: How should I fill firewall holes

Quote:
Originally Posted by bowt1ed
I just cut out slightly over-sized sheet metal circles
How did you cut them out?

So far, various sized washers or just going to the local metal shop for some scraps seems to be the way to go. I like all these genius little tools made from things laying around. I'm new to welding, so my mind doesn't wrap around the idea that I can build all manner of little dohickies for the garage.
__________________
Current Build Thread 1930 Ford Model A Modern Twist: Ford Model A Rat Rod With a Modern Twist

Build Thread Phase 1 "The Swap": 1949 3100 with S10 swap. Beginner build with ambition!

Build Thread Phase 2 "The Drop": Beginner Build with Ambition gets Air Ride
gigamanx is offline   Reply With Quote
Old 10-04-2017, 04:14 PM   #19
gigamanx
Senior Member
 
Join Date: Sep 2016
Location: Hershey, PA
Posts: 1,004
Re: How should I fill firewall holes

Quote:
Originally Posted by hogfarm View Post
I went to the local machine shop and they gave me a coffee can full of the drops from there punch press,all different sizes
That's a great idea!
__________________
Current Build Thread 1930 Ford Model A Modern Twist: Ford Model A Rat Rod With a Modern Twist

Build Thread Phase 1 "The Swap": 1949 3100 with S10 swap. Beginner build with ambition!

Build Thread Phase 2 "The Drop": Beginner Build with Ambition gets Air Ride
gigamanx is offline   Reply With Quote
Old 10-04-2017, 05:48 PM   #20
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: How should I fill firewall holes

for any hole .5'' or under i just welded them closed while holding a piece of brass on the back side
weld won't stick to the brass and the brass acts as a heat sink to prevent weld blow out
a piece of flattened copper pipe works well too, it just gets really hot quickly

for bigger holes i just welded scrap 16 ga squares, carpet covers them well

i shaved the firewall flange while i was at it
Attached Images
  
__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Old 10-05-2017, 04:35 AM   #21
Jesse Z
Account Suspended
 
Join Date: Aug 2016
Location: Florida, USA
Posts: 290
Re: How should I fill firewall holes

Someone prior owner filled all the holes in my firewall, but I can't figure out how. There appear to be plugs inserted in every hole that fit so perfectly without ever being welded that it literally requires a magnifying glass to see them - primer would no doubt cover them completely. Anyone know how this was done?
Jesse Z is offline   Reply With Quote
Old 10-05-2017, 04:51 AM   #22
bennylava
Registered User
 
bennylava's Avatar
 
Join Date: Jul 2017
Location: Texas
Posts: 408
Re: How should I fill firewall holes

Quote:
Originally Posted by bowt1ed View Post
As I recall, I filled around 45 of them.

I can only imagine the massive cost of having a shop do that. Any idea what it would cost?
bennylava is offline   Reply With Quote
Old 10-05-2017, 07:16 AM   #23
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 209
Re: How should I fill firewall holes

I filled over 65 in mine and almost every one was a factory hole!
Dave0 is offline   Reply With Quote
Old 10-05-2017, 11:49 AM   #24
b-mac
Registered User
 
b-mac's Avatar
 
Join Date: Mar 2014
Location: Wichita
Posts: 519
Re: How should I fill firewall holes

I'd recommend one of these.

http://www.eastwood.com/magnetic-hol...8aAkpwEALw_wcB
Attached Images
 
b-mac is offline   Reply With Quote
Old 10-05-2017, 12:05 PM   #25
Dan in Pasadena
Senior Member

 
Dan in Pasadena's Avatar
 
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,343
Re: How should I fill firewall holes

Quote:
Originally Posted by iowaboynca View Post
With all the craftsmanship, i'm a bit embarrassed...
Psh....NO reason to be embarassed. You did the work and if you're pleased with it that's all that matters. Be proud!
__________________
'55 Big Window Shortbed,
Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's

Dan's '55 Big Window "Build" - Well, Kinda!
Dan in Pasadena is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:44 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com