A-pillar problems? Help please. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BustedTruck · 12-31-2017, 03:30 PM

So I've been fighting this area in my truck. What your looking at is the drivers lower a pillar. I'm thinking that the a pillar has twisted somehow. Has anyone else experienced this? I'm thinking the pillar should rest flat on the inner rocker.

**57taskforce** · 12-31-2017, 11:17 PM

Will the bolts pull it tight? Looks to me like they would.

kxmotox247 · 01-01-2018, 01:20 AM

Has the lower section of the pillar been replaced? How much of the outer floor has been replaced? Looks like it should draw up with the bolts as mentioned already.

BustedTruck · 01-01-2018, 05:55 PM

The gap is like 1/2" I bolted some metal & tried to twist it. Didn't work so well. I guess I'll weld it up & try to bolt it back together. Thanks for the help.

**davischevy** · 01-01-2018, 06:14 PM

I think I would bolt it together before I did any welding.

**Boog** · 01-01-2018, 06:45 PM

If it doesn't fit right adjust it until it does before any welding happens.

Wizo · 01-01-2018, 07:31 PM

Somebody please correct if i'm wrong but doesn't the rocker panel go over the A pilar where yo have the three spot welds? Might be why its seems twisted, because your forcing it outwards. just a thought.

Shinysideup · 01-01-2018, 08:06 PM

Looks like those welds have minimal penetration. Low setting and thick wire?

Rufas · 01-01-2018, 08:28 PM

Quote:

Originally Posted by Wizo

Somebody please correct if i'm wrong but doesn't the rocker panel go over the A pilar where yo have the three spot welds? Might be why its seems twisted, because your forcing it outwards. just a thought.

I think you're correct. This is the left drivers side area of my door.

BustedTruck · 01-01-2018, 09:05 PM

Quote:

Originally Posted by Shinysideup

Looks like those welds have minimal penetration. Low setting and thick wire?

Got catch on the welds. That particular piece with the welds is not welded in place. That is the lower kick panel replacement piece. I haven't welded anything in yet. I'm trying to test fit everything before welding. I don't have the brace replaced yet so I can't bolt it up just yet. I can tell you that I bolted a piece of 1/4" bar to the lower post & tried to twist it back into submission, but the whole post moved. I'm going to try to bolt it in & then twist it. The whole thing is I don't remember anything being twisted when I took it apart.

12-31-2017, 03:30 PM	#1
BustedTruck Registered User Join Date: Dec 2006 Location: Braselton, GA Posts: 245	A-pillar problems? Help please. So I've been fighting this area in my truck. What your looking at is the drivers lower a pillar. I'm thinking that the a pillar has twisted somehow. Has anyone else experienced this? I'm thinking the pillar should rest flat on the inner rocker. Attached Images

12-31-2017, 11:17 PM	#2
57taskforce All about them K’s Join Date: Jun 2014 Location: Land of Entrapment Posts: 6,518	Re: A-pillar problems? Help please. Will the bolts pull it tight? Looks to me like they would. __________________ Tyler '57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888 '72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879 ‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206 '98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s

01-01-2018, 01:20 AM	#3
kxmotox247 Senior Member Join Date: Jul 2002 Location: Champaign, IL Posts: 1,397	Re: A-pillar problems? Help please. Has the lower section of the pillar been replaced? How much of the outer floor has been replaced? Looks like it should draw up with the bolts as mentioned already. __________________ Baby Blue's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=652776 Project 68's Build Thread: http://67-72chevytrucks.com/vboard/s...17#post8442117 www.stonecolumnclassics.com Email: Josh@stonecolumnclassics.com

01-01-2018, 05:55 PM	#4
BustedTruck Registered User Join Date: Dec 2006 Location: Braselton, GA Posts: 245	Re: A-pillar problems? Help please. The gap is like 1/2" I bolted some metal & tried to twist it. Didn't work so well. I guess I'll weld it up & try to bolt it back together. Thanks for the help.

01-01-2018, 06:14 PM	#5
davischevy Senior Member Join Date: Sep 2008 Location: Harrison, Arkansas Posts: 9,867	Re: A-pillar problems? Help please. I think I would bolt it together before I did any welding. __________________ other Larry Build thread, Arkansas K10 https://67-72chevytrucks.com/vboard/...=755797&page=5 The ability to speak several languages is an asset, but the ability to keep your mouth shut in any language is priceless.

01-01-2018, 06:45 PM	#6
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,567	Re: A-pillar problems? Help please. If it doesn't fit right adjust it until it does before any welding happens. __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

01-01-2018, 07:31 PM	#7
Wizo Registered User Join Date: Dec 2012 Location: Tacoma WA Posts: 274	Re: A-pillar problems? Help please. Somebody please correct if i'm wrong but doesn't the rocker panel go over the A pilar where yo have the three spot welds? Might be why its seems twisted, because your forcing it outwards. just a thought. __________________ 1970 3/4 ton long box GMC !968 C10 short stepside (Papa's Old Lorry) 2006 2500 HD Silverado Duramax/Alison



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.